Additive manufacturing (AM) has already been evolved into a promising manufacturing technique. In order to achieve the performance of conventionally manufactured components, additively manufactured components must meet at least the same mechanical and physical requirements. Due to the layer-wise building process, the properties of additively manufactured components differ from that of bulk materials. Within the scope of this study, selective laser melting (SLM) was employed to manufacture specimens which serve as substrates for a subsequent coating process. An Inconel 718 (IN718) alloy served as AM feedstock. Mechanical posttreatments were applied to the AM samples and rated with respect to the successive thermal spraying process. The produced AM samples were examined in their initial state as well as under post-treated conditions. In this report, the resulting surface roughness was analyzed. Different AM samples were coated by means of high velocity oxy-fuel (HVOF) spraying and atmospheric plasma spraying (APS). The interface between the thermally sprayed coating and the AM substrate was metallographically investigated. Adhesion tests were conducted to scrutinize the bond strength of the coating to the AM substrate.

In light weight constructions, research focuses more and more on ecological aspects of materials. In this way vulcanized fiber relive a renaissance because it is produced from renewable raw materials. Vulcanized fiber is a composite material, which was approximately discovered in 1855. It is manufactured by parchmentizing of pulp with the use of a zinc chloride solution. This material is well known for its good strength to weight relationship, but it is susceptible to the contact with aqueous fluids and also shows only a low resistance to wear. Therefore, a functionalization of the surface is needed. The functionalization can be realized by thermal spray processes to increase the potential of vulcanized fiber. Especially the pretreatment of the specimen to enable the coating application is one of the key topics of this paper. Vulcanized fiber is a thermal sensitive material. The impact of hot spray materials can cause undesired reactions such as the combustion of fibers on the substrate’s surface. To reduce this effect, twin wire arc spraying and low pressure cold gas spraying processes were used to apply low-melting materials (copper, zinc) onto the specimen. Thereby, the influence of the coating on the vulcanized fiber surface was investigated. In addition, non-destructive testing methods were evaluated to gain information about the vulcanized fiber.

Starting in 2010 a new generation of coal fired power plants in Europe operating at a steam temperature of up 620°C was commissioned. During that commissioning process many cracks occurred in welds of T24 material which was extensively used as membrane wall material in nearly all of the new boilers. The cracks were caused by stress corrosion cracking (SCC) only occurring in the areas of the wall being in contact to high temperature water during operation. The question which step of the commissioning process really caused the cracking was not answered completely even several years after the damage occurred. To answer this question and to define parameters which will lead to cracking in high temperature water many tests were conducted. Generally it was found that slow tensile tests in controlled environment are well suited to get information about materials SCC sensitivity in the laboratory. In the present paper, first the influence of the cracking of welded T24 material in acidic environment containing well-defined amounts of H2S is investigated to address the question if a chemical cleaning process prior to the testing might lead to hydrogen induced SCC. As a second step, cracking behaviour in high temperature water is being investigated. Here the influence of the temperature, the oxygen concentration of the water, the deformation speed of the sample, the heat treatment and the condition of the material on the SCC is analysed.

This paper presents a thickness measurement method that can be used during thermal spraying. The new method is based on photogrammetry and image reconstruction and is able to measure complex 3D shapes with continuous contours. Initial results demonstrate the nondestructive nature of the method as well as its accuracy, versatility, and speed.

This study demonstrates an experimental setup in which acoustic emission sensing is used to monitor a twin wire arc spraying (TWAS) process. Emitted acoustic signals were recorded by broadband sensors attached to the spray nozzle and mounted under the substrate. Sensor outputs were converted from the time domain to the frequency domain by fast Fourier analysis. Acoustic emission amplitude plots were produced and are correlated with gas pressure, arc voltage, in-flight particle velocity and temperature, coating thickness, and crack formation due to cooling.

One of the greatest obstacles for a wide distribution of thermal spraying techniques is the lack of online control over the spraying process. The thermally sprayed coatings are optimized by an empirical modification of the spraying parameters and the subsequent correlation of these parameters to the obtained coatings. Some intrinsic parameters, such as the fluctuations in twin wire arc spraying and wear in the atomization nozzle, are not adjustable. Even though they have an enormous impact on the obtained coating quality, they are often scientifically neglected for reasons of simplification. In this work, acoustic emission analysis is utilized to study the effect of uncontrollable parameters on acoustic signals. In order to enable an easy determination of the changes in the acoustic signals, the acoustic sensors were mounted on the spraying nozzle as well as on the substrate. At increased current, a lower acoustic emission is recorded. A correlation between uncontrollable parameters, the acoustic signals, and the obtained coating quality was observed. This research contributes to the online control of the spraying process.