The global radio frequency (RF) semiconductor market size is growing dramatically in recent years, especially with the growing demand for mobile devices, communication networks, automotive applications, etc. Failure analysis (FA) on RF devices is normally more complex than digital devices, especially when it involves soft failure. This paper discusses FA on an RF product soft failure issue by the pulsed currentvoltage (IV) nanoprobing technique. The device suffered from high-frequency failure and exhibited abnormal repetitive softstart signature. Previous publications on pulsed IV nanoprobing applications were mostly related to Front End Of Line (FEOL) issues and simulations. In most of these cases, the electrical abnormality could also be observed with normal DC IV measurement. In this paper, the pulsed IV nanoprobing was performed at the Back End Of Line (BEOL) interconnects to isolate the failure that was otherwise not detected with normal DC nanoprobing or the reported pulse IV measurement. The proposed method successfully isolate, simulate the failure, and helping us to identify the process and design rule weakness.

With technology scaling of semiconductor devices and further growth of the integrated circuit (IC) design and function complexity, it is necessary to increase the number of transistors in IC’s chip, layer stacks, and process steps. The last few metal layers of Back End Of Line (BEOL) are usually very thick metal lines (>4μm thickness) and protected with hard Silicon Dioxide (SiO2) material that is formed from (TetraEthyl OrthoSilicate) TEOS as Inter-Metal Dielectric (IMD). In order to perform physical failure analysis (PFA) on the logic or memory, the top thick metal layers must be removed. It is time-consuming to deprocess those thick metal and IMD layers using conventional PFA workflows. In this paper, the Fast Laser Deprocessing Technique (FLDT) is proposed to remove the BEOL thick and stubborn metal layers for memory PFA. The proposed FLDT is a cost-effective and quick way to deprocess a sample for defect identification in PFA.

With the scaling of semiconductor devices to nanometer range, ensuring surface uniformity over a large area while performing top down physical delayering has become a greater challenge. In this paper, the application of laser deprocessing technique (LDT) to achieve better surface uniformity as well as for fast deprocessing of sample for defect identification in nanoscale devices are discussed. The proposed laser deprocess technique is a cost-effective and quick way to deprocess sample for defect identification and Transmission Electron Microscopy (TEM) analysis.

Top-down, layer-by-layer de-layering inspection with a mechanical polisher and serial cross-sectional Focused Ion Beam (XFIB) slicing are two common approaches for physical failure analysis (PFA). This paper uses XFIB to perform top-down, layer-by-layer de-layering followed by Scanning Electron Microscope (SEM) inspection. The advantage of the FIB-SEM de-layering technique over mechanical de-layering is better control of the de-layering process. Combining the precise milling capability of the FIB with the real-time imaging capability of the SEM enables the operator to observe the de-layering as it progresses, minimizing the likelihood of removing either too much or too little material. Furthermore, real time SEM view during top-down XFIB de-layering is able to provide a better understanding of how the defects are formed and these findings could then be feedback to the production line for process improvement.

With the scaling down of semiconductor devices to nanometer range, fault isolation and physical failure analysis (PFA) have become more challenging. In this paper, different types of fault isolation techniques to identify gross short failures in nanoscale devices are discussed. The proposed cut/deprocess and microprobe/bench technique is an economical and simple way of identifying low resistance gross short failures.

Electrical Test (ET) structures are used to monitor the health and yield of a process line. With the scaling down of semiconductor devices to nanometer ranges, the number of metal lines and vias increase. In order to simulate the electrical performance of devices and to increase the sensitivity for line health check, ET structures are designed to be more complicated with a larger area. Hence, fault isolation and failure analysis become more challenging. In this paper, the combined technique of Scanning Electron Microscope (SEM) Passive Voltage Contrast (PVC), Nanoprobing technique, and Divide and Conquer Method (DCM) are proposed to locate open failure and high resistance failure in an ET via chain.

The scanning electron microscope (SEM) based nanoprobing technique has established itself as an indispensable failure analysis (FA) technique as technology nodes continue to shrink according to Moore's Law. Although it has its share of disadvantages, SEM-based nanoprobing is often preferred because of its advantages over other FA techniques such as focused ion beam in fault isolation. This paper presents the effectiveness of the nanoprobing technique in isolating nanoscale defects in three different cases in sub-100 nm devices: soft-fail defect caused by asymmetrical nickel silicide (NiSi) formation, hard-fail defect caused by abnormal NiSi formation leading to contact-poly short, and isolation of resistive contact in a large electrical test structure. Results suggest that the SEM based nanoprobing technique is particularly useful in identifying causes of soft-fails and plays a very important role in investigating the cause of hard-fails and improving device yield.

Electrical characterizations were needed to identify the root cause of leakage issues in IC devices. The methodology required was dependent on the failure mode obtained during testing and global or nano-scale isolations had to be implemented accordingly. As such, challenges encountered in sample preparation or due to detection methodology choices for every isolation technique have to be addressed in order to localize the defective sites.

With the scaling down of semiconductor devices to nanometer range, physical failure analysis (PFA) has become more challenging. In this paper, a different method of performing PFA to identify a physical vertical short of intermetal layer in nanoscale devices is discussed. The proposed chemical etch and backside chemical etch PFA techniques have the advantages of sample preparation evenness and efficiency compared to conventional PFA. This technique also offers a better understanding of the failure mechanism and is easier to execute in identifying the vertical short issue.