The adhesion mechanisms involved in the cold spray coatings are not still well elucidated. The quality of the deposit does depend mainly on particles and dynamic characteristics (which result from nozzle type, nozzle-substrate distance, etc.). The present work is based on the study of particle-substrate and particle-particle interfaces in the tantalum-copper coating-substrate system. The content focuses on the influence of the oxygen content in the starting powder on interface features, consequently on coating properties. Tantalum powders with different oxygen levels were studied using SEM (Scanning Electron Microscopy) and EPMA (Electron Probe Microanalysis). Laser shock spallation of cold-sprayed Ta coatings was developed as a reliable and flexible process to achieve Ta spalls to be deposited at a high-velocity onto Cu targets. The velocity due to the laser shock could be controlled to be similar to that of particles in conventional cold spray. This results in Ta-Cu interfaces, the study of which was carried out to go into interface phenomena involved in cold spray, using TEM (Transmission Electron Microscopy) in particular. Results were compared to those obtained from laser shock spallation of Ta bulk specimens (i.e. made of a conventional Ta sheet). The role of powder oxidation on interface soundness was exhibited. Adhesion was shown to be all the lower as powder oxygen content was higher, using LASAT (“ Laser Shock Adhesion Test”) in addition to direct observation of interfaces. Results were exploited to discuss properties of the corresponding Ta coatings onto Cu, i.e. which were cold sprayed using powders with different oxygen contents.

In this study, fine aluminum powder was cold sprayed onto aluminum substrates, some of which were polished, some grit blasted, and some pretreated using a nano-pulsed Nd:YAG laser. In the latter case, the laser is coupled with the cold spray gun and the irradiation treatment occurs just prior to deposition. To better understand the interaction mechanisms involved with laser pretreating, coating-substrate interfaces were examined on thin-foil specimens and adhesion strength was determined by laser shock testing. The results show that substrate pretreatment with a nano-pulsed laser significantly improves the coating-substrate interface as well as coating adhesion.

Cold gas dynamic spraying, namely cold spray, is an innovative coating process in which powder particles are injected in a supersonic gas flow to be accelerated above a certain critical velocity. Even though particles adhesion onto the substrate has not be yet elucidated, it appears clearly that it is influenced by particle impact velocity, which results from spraying conditions, diameter of particles and their positions from the center of the particle jet. Particle velocity can change dramatically depending on particle position from the core to the rim of the jet. In the present work, an original experimental set-up was designed to discriminate the particles as a function of the levels of velocity to investigate the influence of this parameter on adhesion. Particles at given positions in the jet could therefore be observed using SEM (Scanning Electron Microscopy), which showed different morphologies and microstructures as a function of impact velocity. High pressure and tangential velocity at the interface during impact were calculated from numerical simulations using ABAQUS. TEM (Transmission Electron Microscopy) analyses of thin foils were carried out to investigate into resulting local interface phenomena. These were correlated to particle impact velocity and corresponding adhesion strength which was obtained from LASAT testing (LAser Shock Adhesion Test).

Thermal-sprayed (i.e. LPPS or HVOF) MCrAlY coatings are widely used for land-based gas turbine applications against high-temperature oxidation and hot corrosion. However, due to requirement for further improvement of turbine efficiency, dense and stable coatings are necessary. The cold spray (also referred to as cold gas dynamic spray) makes it possible to increase coating density, due to high velocity particle impact during spraying. However, deposition mechanisms of cold spraying have not been elucidated yet. In this study, we investigated the deposition mechanisms focused on the behavior of interface between a coating and a substrate. The mechanisms were evaluated by the spray impact phenomena simulation tests, namely laser shock flier impact tests, and STEM-EDX elemental analyses at the interface between the substrate and the cold sprayed coating. From the results of STEM-EDX for as-sprayed coating and of SEM-EDX of the flier specimen, the bonding between the CoNiCrAlY coating and the substrate occurred at the only particular phase combination.

Coating-substrate adhesion in cold spray is a paramount property, the mechanisms of which are not yet well elucidated. These mechanisms are governed by metallurgical and morphological phenomena occuring when cold-sprayed particles impinge on the substrate. To go into these mechanisms, due to the intrinsic characteristics of the cold spray process, i.e. the low-temperature and high velocity of the particles, direct observation and control of inflight particles and related phenomena (especially when impinging) cannot be done easily. For this reason, an experimental simulation of the particle-substrate reactions at the particle impingement was developed. This simulation is based on original filter impact experiments from laser shock acceleration of plates/foils (fliers). These were applied to the Cu-Al metallurgically-reactive system to simulate Cu cold-sprayed onto Al. The velocity of the plate was selected in the range of actual cold spray velocities. Relevant Cu-Al interaction phenomena were featured and studied as a function of filter impact conditions, i.e., primarily, shearing, plastic deformation, phase transformation (including rapid melting/solidification and formation of intermetallics). These phenomena were shown to be similar to those involved in cold spray. This was ascertained by a parallel study of cold-sprayed Cu coating of Al using SEM, TEM, EPMA, and an energy balance and diffusion calculations. In addition, this simulation can be used to feed FE modeling of cold spray particle impingement on the substrate. Preliminary results are discussed from modeling using the “RADIOSS®” code. More generally, laser shock flier impact experiments were demonstrated to result in a powerful tool capable of simulating cold spray coating-substrate interface mechanisms. Major assets rest on their high significance, reproducibility, flexibility and potential for substituting for direct laborious cold spray optimization testing.

The adhesion strength of a ceramic coating deposited through direct spraying on a roughened substrate is a key issue in the manufacture of high-quality coatings on industrial components. The purpose of this work was to develop a rapid and discerning procedure for establishing adhesion level of a ceramic coating on a metallic substrate. The Laser Shock Adhesion Test, namely LASAT, was successfully applied to ceramic coatings with irradiation impact on the metallic side. Suitable parameters were found to determine the LASAT adhesion threshold using a standard Nd:YAG laser source. With a laser-irradiated area of several millimetres in diameter, it allowed assessment of the coating threshold on several areas of a coated plate sample. A control procedure for a qualitative assessment of coating adhesion was developed. This testing procedure could be easily used in industry, with possible location of the LASAT unit near to the spraying booth, for a direct production control on coated sample to improve the tracability of manufactured parts. Additional work was carried out to investigate a quantitative approach of the LASAT test to ceramic coating. The purpose was to simulate the shock wave propagation with the RADIOSS® code (a 3D software originally developed for car crash simulation). This code was implemented to calculate the velocity of the material and corresponding pressure throughout the substrate and the coating during the shock wave release (less than 2 ms). Experimental VISAR profiles ('Velocity Interferometer System for Any Reflector') were monitored in the straight direction of the laser-irradiated area on the rear side. These experimental signals (velocity measures) of the ceramic coating could be fitted and compared with a fairly good agreement with simulated profiles obtained by RADIOSS®. This modelling work was the first step towards a more comprehensive coating adhesion strength calculation in the future.

To address drawbacks with conventional destructive adhesion tests, two advanced nondestructive methods were developed to characterize the acoustic response of coating-substrate bonding. These new tests, immersion ultrasonic testing and laser shock adhesion testing, are discussed in this contribution. The paper describes the test process and results as compared to traditional destructive testing. The advantages and drawbacks of the techniques are addressed.

This paper discusses the principles of laser shock adhesion testing, a nonintrusive method for measuring the bonding strength of coatings. The technique uses a laser to generate a thermal shock in the substrate, while Doppler laser interferometry is used to detect detachments. An application example is presented in which the method is employed to measure the adhesion strength of a plasma-sprayed copper coating on an aluminum substrate. The results are compared with numerical simulations of shock wave propagation. Paper includes a German-language abstract.

The adhesion of copper on aluminum depends on the presence of intermetallic phases. Such phases can form during spraying at the interface between the layer and substrate. This paper deals with the formation mechanism of the intermetallic phases and their influence on adhesion. The type, size, and distribution of the intermetallic phases are investigated as a function of spray parameters and bonding strength is determined by laser shock adhesion testing. Paper includes a German-language abstract.