In this study, ceramic-matrix composites consisting of elongated metal (CoNbZr) particles in a cordierite (MgAlSiO) matrix were produced by plasma spraying. The metal powder was injected into the plasma jet downstream of the ceramic powder to minimize metal decomposition and oxidation. The microstructure and composition of cermet coatings containing 5, 10, and 20 vol% metal were analyzed by SEM and XRD and their electromagnetic properties were evaluated via saturation magnetization, permittivity, and permeability measurements. As expected, flake-shaped metallic particles were obtained and all coatings exhibited soft ferromagnetic behavior.

To answer current issues adequately considering technical, economic, as well as environmental requirements, material transformation and especially surface treatment industries must be source of innovations to be proactive. As a result, developing new alternative solutions to existing ones had become a top priority. Considering surface treatment processes, conventional ones (thermal spraying, plasma transferred arc) do not allow to consider this approach since the processes themselves (co-treatment of different powders) do not permit to guarantee the initial composition nor do they ensure a sufficient homogeneity to the coating structure. If indeed the dry surface treatment processes have already shown large potential, several limits remain such as an inefficient adhesion, an environmental impact over the life cycle or almost no materials on the market. To overcome these issues hybrid coating technologies (combining several processes) are likely to be developed. From all of them, laser technology seems to be very promising due to its high flexibility considering all the potential parameters (varying power, continuous or pulsed beam, etc.) and the localised treated area. For instance, combining simultaneously a laser with a thermal spray process enables the elaboration of a thick coating showing a good adherence. The ablation laser applied on the substrate surface just before the impacting particles as promoted in the PROTAL process permit to insure a suitable surface state favourable to the particles adhesion. The control of the coating microstructure was not so much studied. That is why, to complete the knowledge in this area, this work aims at studying the influence of laser technology in association with plasma spraying on the coating microstructure and more precisely on the coating mechanical properties. Coatings were characterized by SEM and void content was evaluated through image analysis and Archimedean porosimetry. Mechanical properties were assessed by the four points bending test for evaluating the coating apparent Young modulus.

Tungsten-based cermets are well-known engineering materials finding applications in aerospace, nuclear equipment, and many other fields. Plasma spraying is an interesting industrial process to manufacture those refractory materials. Original plasma sprayed hard coatings for wear protection composed of a stainless steel matrix and inclusions of tungsten carbide (WC) nanoparticles were developed. To built-up the coatings, two precursors were injected separately in the plasma jet : a stainless steel micrometric powder was classically injected into the plasma jet using a carrier gas whereas WC nanoparticles were injected with a liquid carrier, like in the so-called process suspension plasma spraying. One of the challenges is to maintain the WC phase stoichiometry in the deposit, without decomposing the carbide into brittle W 2 C, W 3 C, and metallic tungsten, phenomenon usually occurring with thermal spraying techniques. Another issue is to succeed in including homogeneously the carbide nanoparticles in a sufficiently dense stainless steel matrix. Coatings with different WC contents were deposited on stainless steel substrates and investigated with respect to their microstructure by optical and scanning electron microscopy, porosity level using the Archimedean method, phase composition by X-ray diffraction and Vickers micro-hardness. Results have shown that coatings consisting of a stainless steel matrix containing inclusions of carbide nanoparticles can be produced by plasma spraying. The phase composition analysis indicated that nanoparticles are largely composed of the WC phase and contain a small amount of WC1-x phases. A slight increase of the porosity level was measured for coatings containing nanoparticles, compared to the pure matrix, probably due to the cooling effect of the WC carrier liquid on the in-flight characteristics of the stainless steel particles. Micro-hardness measurements gave similar values for with or without nano-sized particles, showing that the amount of WC included in the samples was insufficient to improve the hardness property.

Suspension plasma spraying (SPS) is able to process a stabilized suspension of nanometer-sized feedstock particles to form thin (from 20 to 100 µm) coatings with unique microstructures. The void network architecture of these ceramic coatings is a challenge to be characterized and quantified using commonly used techniques due to small sizes involved. Nevertheless, the discrimination of these pore architectures in terms of size and shape distribution, anisotropy, specific surface area, etc., is critical for the understanding of processing, microstructure, and properties relationships. USAXS (Ultra-Small Angle X-Rays Scattering) appeared as a suitable measurement technique allowing discriminating the void size distribution over a large range (up to four orders of magnitude). Results indicate that as-sprayed SPS coatings exhibit unusual porous architecture: 1) average void size is about the same than the feedstock one; i.e., nanometer sizes with multimodal void size distribution; 2) about 80% of the voids exhibit characteristic dimensions smaller than 30 nm; 3) the total void content varies between 13 to 20% depending upon considered operating parameters. In-situ annealing measurements were performed as they proved to deliver more relevant results compared to ex-situ measurements: even at temperatures as low as 800°C, the microstructure transforms - while the total void content does not change significantly. Indeed, it has been demonstrated that the smallest voids (equivalent diameters smaller than 50 nm) coalescence was the predominant mechanism and that it was more sensitive to temperature than time.

A new challenge in the field of Solid Oxide Fuel Cells (SOFCs) concerns the reduction of their operating temperature down to 700°C. Apatite ceramics are interesting alternatives for SOFC electrolytes due to their high ionic conductivity at this temperature. The present work reports on the manufacturing and characterization of La 9 SrSi 6 O 26.5 coatings obtained by atmospheric plasma spraying at two different plasma spray powders. The microstructure and the composition of the as-sprayed and heat-treated coatings were investigated by several techniques including X-Ray Diffraction, Inductively Coupled Plasma - Atomic Emission Spectroscopy as well as Scanning and Transmission Electron Microscopy. The porosity level of the coatings was evaluated by the Archimedean method and image analysis. The studies revealed that the as-sprayed apatite coatings were composed of an amorphous phase, a crystalline apatite phase and chemical heterogeneities due to Si volatilization in the high-temperature plasma. Furthermore, a heat treatment made it possible to obtain denser, fully crystallized apatite coatings and also improved their ionic conductivity.

This study investigates the feasibility of manufacturing lanthanum silicate coatings for solid oxide fuel cells by atmospheric plasma spraying. The coatings produced are cohesive, relatively dense, and contain no secondary phases. Test results show that the starting composition of the powder is maintained after spraying and that particle velocity depends primarily on the plasma gas mixture. Due to the relatively high melting temperature of the particles, dense apatite coatings with few microstructural defects are obtained.

Intermediate temperature solid oxide fuel cells include in their design a solid electrolyte layer, usually made of yttria-stabilized zirconia, that acts as an ionic conductor through which oxygen ions diffuse. This layer must be as thin as possible to limit ohmic losses yet have a low leakage rate corresponding to a low level of connected stacking defects such as microcracks. Suspension plasma spraying (SPS) appears to be a viable method for manufacturing such layers and is used in this study to produce gastight coatings that with further improvements may meet the requirements of SOFCs. The paper describes the setup and optimization of the SPS process and the methods used to evaluate the solid electrolyte layers.

For different applications, it is on interest to understand the relationship between the microstructure and the transverse permeability of a plasma sprayed coating. In the SOFC field, for example, the electrodes are very often characterized in term of porosity, particularly when they are elaborated by sintering. This can’t be applied to thermally sprayed coatings because of their very singular microstructure, lamellar and isotropic, depending strongly on the initial material and plasma conditions. In this study, coatings were manufactured by plasma spraying using different spraying parameters, many proportion of a porous agent, metallic or ceramic powders and two particles size in order to obtain various microporous structure. Measurements of their permeation with the pressure drop method and their open porosity just as the observation of the morphology and the structure by optical microscopy were achieved. The different data show that the evolution of the transverse permeability with the open porosity follows the Kozeny-Carman equation. This result correlated with the microstructural observation highlights the relationship between the permeability and the physical properties of porous plasma sprayed layers.

A new thermal spray process is under development in order to produce thin coatings (thickness lower than 50 µm), with a fine microstructure (grain size smaller than 1 µm). It consists in injecting in a Direct Current (D.C.) plasma jet a suspension containing submicronic particles of the material to be deposited. To study the interaction between the plasma jet and the suspension, a system based on a pendulum allows the collection of particles at different distances from the injection point. In this paper the effect of substrate temperature upon the formation of micrometric zirconia splats was studied, glass and stainless steel were used as substrate materials.