Recent studies have demonstrated that WC-12Co and WC- 10Co-4Cr coatings were the best performing HVOF coatings against erosion. This paper looks at the influences of the HVOF process parameters for WC-12Co and WC-10Co-4Cr materials on the erosion resistance of the coatings. The effect of powder morphology, matrix chemistry and HVOF process parameters with respect to both silica slurry erosion and alumina dry erosion has been studied. All coatings were produced using the HVOF JP-5000 system with kerosene-oxygen flame. The spraying parameters were analyzed in term of sprayed particle velocity and temperature as measured with the DFV2000 optical diagnostic system. Simultaneously with in-flight particle measurements, the substrate-coating temperature was monitored by infrared pyrometry during coating deposition. The resulting coating microstructure was evaluated in terms of microhardness, porosity type and extent of wear damage after dry and slurry erosion. The material volume loss under various erosion conditions was related to the coating properties and microstructure. According to the experimental results, the following conclusions are drawn: 1) the kerosene flow rate affects the inflight particle state (velocity and temperature) and the coating porosity. 2) Cobalt-chrome matrix cermet performs better in slurry erosion while denser and harder cobalt matrix cermet performs better in dry erosion. 3) The use of kerosene-rich flame with lower oxygen stoichiometry reduces the carbide degradation and optimizes the wear performance of WC-12Co coatings in both dry and slurry erosion.

Arc spraying can be used to produce coatings to protect against wear and tear against erosion. This paper presents some results obtained within the core research program of the NRC Technology Group in Surface Engineering on the development of erosion-resistant coatings. A relationship is established between the volume loss of the material (performance) under different erosion conditions and the coating properties or the microstructure. The results show that the wear behavior of the arc-sprayed materials depends on the type, size and impact strength of the impacting eroding particles. It is observed that for soft materials, even if ductile tearing is an active mode of degradation, the brittle behavior of intersplat oxides also plays an important role. For harder materials, this brittle delamination of splats becomes the dominant erosive mechanism, as can be observed on the worn surfaces. Paper includes a German-language abstract.

Improvement of the high velocity oxy-fuel deposition (HVOF) process in the last decade has led to coatings with significant improved microstructures for better protection against wear and corrosion. HVOF coatings of cermet and metallic materials provide protection against erosion and are therefore good alternatives to the use of high-priced material. This paper presents the results of a study undertaken within the core research program of the National Research Council of Canada technology group in surface engineering, "SURFTEC", in which the performance of ten HVOF erosion-resistant coatings were evaluated under both dry and slurry erosion. Ten different types of HVOF coatings were studied including: six grades of WC with either Co or a Ni based matrix, one grade of Cr3C2 in a Ni-Cr matrix, and three grades of metallic alloy: Ni alloy, Co alloy and a SS 316-L. Coatings performance was evaluated with respect to the volume ratio and composition of metallic binder in carbide coatings, type of carbide, coating microstructure, impinging angle and the size of the erodent particles. All coatings were produced using the HVOF IP5000 system controlled by the Hawcs-II controller. Slurry jet erosion tests were conducted using a 10 %w/w alumina particle/water slurry. Two alumina particle sizes, 320 and 80 grit (nominal grain diameters 35 μm and 200 μm, respectively) were used. The nominal impact velocity of the slurry was 15 m/s and the nozzle-specimen distance 100 mm. Dry erosion tests were conducted using 50 μm diameter alumina particles projected onto coated flat test coupons through a carbide nozzle of diameter 1.14mm with a particle velocity of 84 m/s at a feed rate of 2 ±1 g/min. let impingement angles of 90° and 20° were used for both dry and slurry erosion tests. The volume loss of material under various erosion conditions was related to the coating properties and microstructure. Results indicate that the coating behavior is dependent on the erodent particle size, the erosion impinging angle to some extent and for slurry erosion, to the corrosion resistance of the cermet matrix.