This work deals with ZrB 2 -based coatings prepared by inert plasma spraying and their behavior under high heat flux in moist atmospheres. ZrB 2 coatings with different compositions and microstructures were produced and subjected to high-temperature oxidation testing in order to identify the most oxidation-resistant sample. It is shown that coating microstructure can significantly influence oxidation kinetics and that uniformly dispersed nanoscale additives are particularly effective for slowing oxidation.

The aim of this study is to evaluate the thermal lifetime properties of yttria-stabilized zirconia (YSZ) coatings with a columnar microstructure. YSZ suspensions were sprayed under different conditions in order to obtain a sample lot with columnar microstructures varying from well-separated to closely spaced. Thermo-cyclic fatigue (TCF) tests were performed at 1100 °C and the results are presented. Coatings with well-separated columns reached 2150 cycles prior to failure compared to 1300 cycles in the case of coatings with compact columns. The apparent lower TCF resistance is attributed to a loss of thermal compliance inducing the development of sharp intercolumnar cracks. Failures seem to be linked to debonding at the TGO-substrate interface. The bond coat and substrate surface roughness also play a role in such failures and their impact is discussed.

Normal hemispherical spectral reflectances of plasma sprayed Al 2 O 3 /Al cermets were measured from visible to infrared wavelengths for several metal concentrations ranging from pure alumina to aluminum. Microstructure and composition of the samples were carefully characterized to explain their optical response, highly dependent on volume and/or surface scattering. Besides their contribution to the knowledge of microstructure, 2D scanning electron microscopy and 3D micro-tomography images were exploited to get statistical data in order to generate simplified numerical samples. A Monte Carlo ray-tracing model was then intended to reproduce experimental trends of the optical spectra. A good agreement with the experimental data was obtained.

Very low pressure plasma spraying (VLPPS) is an emerging process allowing manufacturing oxide and metallic coatings by condensation of vapors generated by feedstock powder vaporization. This process operates at unusually low pressures, typically between 100 and 1000 Pa. This paper aims at presenting recent developments for manufacturing Ti,Al,N coatings via a reactive mode. At first, nitrogen was used as the primary plasma forming gas to enrich spraying surrounding with nitriding species. Plasma jet mass enthalpy and substrate surface temperature were varied to evidence nitride phase formation during spraying. Then, a secondary nitrogen injection was implemented and located close to the surface to be covered in view of creating a continuous nitrogen supply to promote the nitriding mechanisms on the surface. SEM, XRD, GDOES and NHT were implemented to characterize coatings structure. This study highlights the nitrides formation versus spray operating conditions. The microstructural and mechanical features as well as the chemical composition are presented.

This work evaluates the potential of using a plasma spray process to introduce SiC into zirconia diboride ceramic coatings. Controlling the spraying of the ultra-refractory compound ZrB 2 is the first challenge as it represents the matrix in which SiC particles will reside. To that end, the experiments focus on spraying parameters that influence the plasma jet and the nature of the precursor feedstock. The results show that ZrB 2 coatings containing controlled amounts of SiC can be obtained through high-energy suspension plasma spraying. The ZrB 2 -SiC coatings will be evaluated in a high-temperature oxidative environment in future work.

Very low pressure plasma spraying (VLPPS) has been used to manufacture thin, dense, finely-structured ceramic coatings for various applications. This paper presents the results of work in which VLPPS is used to deposit metal. Aluminum was chosen as a demonstrative material, due to its moderate vaporization enthalpy (38.23 KJ·cm -3 ), with the objectives of better understanding the behavior of a solid precursor injected into the plasma jet, leading to the formation of vapors, and controlling the factors affecting coating structure. Nearly dense aluminum coatings were successfully deposited by VLPPS at 100 Pa with an intermediate power (45 kW) plasma torch. Optical emission spectroscopy (OES) was used to observe the behavior of the metal powder injected into the plasma jet, and simplified CFD modeling provided a better understanding of thermophysical mechanisms. The effect of powder size distribution, substrate temperature, and spray distance were studied. Coatings were characterized by SEM observations and Vickers microhardness measurements.

Yttrium silicates are among the candidates for protection of silicon-based ceramics in high temperature and moist environments due to chemical and mechanical compatibility with substrate, low volatility and moisture resistance. Here we reported on the development of yttrium silicate coatings by sol precursor plasma spraying. The use of a sol feedstock allowed easy composition flexibility. The microstructure and the structure of as-sprayed and heat-treated coatings were investigated. Finer microstructure was obtained compared to micrometric powder plasma spraying traditionally used to produce environmental barrier coatings (EBC). XRD analyses on as-sprayed coatings revealed amorphous or crystalline layers depending on plasma parameters. In EBC application, a volume change from crystallization or phase transformation was envisaged to be damaging due to induced stresses and fully crystalline phases are a key durability requirement for EBC from conventional plasma spraying. Yttrium silicates are characterized by an important polymorphism and the ability to form amorphous coatings. Therefore, special attention was so paid to the amorphous degree of the coatings.