High-entropy alloys (HEAs) represent a new class of advanced metallic alloys that have gained significant interest. They offer a unique combination of mechanical, thermal, and functional properties, making HEAs ideal for various industrial applications. One such alloy is the recently developed equiatomic body-centred cubic phase AlCoCrFeMo. In particular, thermally sprayed AlCoCrFeMo coatings have gained wide interest due to their exceptional mechanical properties compared to common industrial steel. In the current study, the effect of Mo concentrations on the strength of single crystal AlCoCrFeMo HEA was investigated using molecular dynamics simulation and the phase stability of the alloy was studied using polyhedral template matching. Our results indicate that the local lattice distortion of the alloy is not significantly related to Mo concentration. The yield strength of AlCoCrFeMo HEA obtained through tensile loading, was found to increase with Mo concentration, at a molar ratio of Mo higher than 0.5. Investigation of the deformation behavior of the HEA revealed that bands with high shear strains evolved during plastic deformation. The formation of shear bands after the yield point elucidated the softening exhibited by the material due to localized deformation. These findings provide guidance for tailoring the mechanical properties of AlCoCrFeMo HEA by adjusting Mo concentrations, offering new avenues for designing functional coating materials.

Graphite is useful in high-temperature applications in many engineering fields, such as heat-treating, brazing, and sintering industries. As the operation becomes severe, carbon experiences degradation leading to failure. In this study, a protective coating of W and Mo as the intermediate layer by air plasma spraying on graphite substrate was investigated to find a better intermediate layer. Their performance was explored as a bonding layer in a protective alumina-YSZ ceramic topcoat. X-ray diffraction and scanning electron microscope were used to observe the cross-section of coatings and the difference in the bonding characteristics between W and Mo, respectively. W was found inferior to Mo as a bonding performance over 1450 °C in view of carbide formation against the thermodynamic data. It seems to be related to the formation of a barrier layer as oxide during air plasma spraying.

This paper presents the results of two metals coatings, molybdenum and tantalum, prepared by Controlled Atmosphere Plasma Spray (CAPS) onto Al 6061 substrates that were thermal cycled to calculate the effective coating modulus. Traditional uniaxial tensile testing samples were prepared from thicker duplicate coatings for comparison, as well as to measure thermal expansion properties and oxygen and nitrogen content. The molybdenum samples cut from thicker coatings were un-able to be tensile tested due to their fragility. Thermal cycle testing of molybdenum on an Al 6061 substrate was found to have a modulus approximately 18 to 19% of literature values for bulk molybdenum using the bi-layer beam thermal cycling method. Additionally, non-linear modulus behaviour was observed in the molybdenum sample when enough thermal strain was induced to shift the coating from a compressive to tensile stress state. The tantalum coating was found to have a modulus approximately 42 to 46% of literature values for bulk tantalum using the bi-layer thermal cycling method. Traditional tensile testing measured a modulus approximately 44 to 46% of bulk, which shows good agreement between the two methods and supports that the bi-layer thermal cycling method is valid for plasma sprayed refractory metal coatings.

Lead, lead-bismuth, or lead-lithium are candidate materials for liquid metal-based cooling media in the new generation of nuclear fission reactors and fusion systems. There are many benefits of using this concept; however, a new problem arises too: preventing degradation of structural materials that are supposed to come into a direct contact. Therefore, new steel grades are being designed, and technological workarounds are searched for. One of the pathways could be a deposition of thick, long-term stability protective coatings onto the steel surfaces. In our opening study, we have employed CS and RF-ICP technologies to deposit Mo and Fe coatings onto ferritic-type 9% Cr Eurofer steel and its ODS variant, and tested them in the PbLi environment at 600 °C for up to 1000 hours. The results suggest that the Fe coatings showed a promising resistance to the corrosive medium and are worth studying deeper.

The addition of refractory metals represents a promising development approach for future high-entropy alloys (HEAs). Niobium and molybdenum are particularly suitable for increasing hardness as well as wear and corrosion resistance. In the context of surface protection applications, eutectic alloys with their homogeneous property profile are of particular interest. In the present work, two eutectic HEAs (EHEAs) were developed for the starting Al 0.3 CoCrFeNi using electric arc furnace. Following mechanical and microstructural characterization, the two alloys Al 0.3 CoCrFeNiMo 0.75 and Al 0.3 CoCrFeNiNb 0.5 were identified. For thermal spray processing, powders were prepared by inert gas atomization. The coatings produced by high velocity oxy-fuel (HVOF) spraying were characterized and evaluated comparatively to the castings, allowing process-structure-property relationships to be derived. Based on the results, statements on possible application potential can be made.

Fatigue crack growth in self-standing plasma sprayed tungsten and molybdenum beams with artificially introduced notches subjected to pure bending was studied. Beams width, thickness and length was 4 mm, 3 mm and 32 mm respectively. Fatigue crack length was measured using the differential compliance method and fatigue crack growth rate was established as a function of stress intensity factor. Unusual crack opening under compressive loading part of the cycle was detected. Fractographic analysis revealed the respective crack formation mechanisms. At low crack propagation rates, the fatigue crack growth takes place by intergranular splat fracture and splat decohesion for Mo coating. In W coating, intergranular splat fracture and void interconnection formed the fatigue crack. Frequently, the crack deflected from the notch plane being attracted to stress concentrators formed by porosity. At higher values of the stress intensity factor, the splat intergranular cracking become more common and the crack propagated more perpendicularly to the specimen surface.

Disk splats are usually observed when the deposition temperature exceeds the transition temperature, whereas thick oxide layer will reduce the adhesion resulting from high deposition temperature. In present study, single molybdenum splats were sprayed onto polished molybdenum substrates with different preheating processes to clarify the effect of surface oxidation on the splat formation. Three preheating processes included heating the substrate to 350 °C, 550 °C, and cooling the substrate from 550 °C to 350 °C, which were performed in argon atmosphere. The chemistry and compositions of substrate surface was examined by XPS. The cross sections of splats were prepared by focus-ion-beam (FIB), and then characterized by SEM. Nearly disc-shaped splat with small fingers in the periphery was observed on the substrate preheated to 350 °C. Perfect disc-shape splat was deposited at 550 °C. Flower-shaped splat exhibited a central core and discrete periphery detached by some voids on the substrate preheated to 350 °C (cooling down from 550 °C). The results of peeling off splats by carbon tape and morphology of FIB sampled cross-sections indicated that no effective bonding formed in the splat-substrate interface for the substrate ever heated to 550 °C, due to the increasing content of MoO 3 on preheated molybdenum surface.

Due to high melting temperatures and excellent corrosion resistance of refractory metals, they are used for manufacturing parts working under extreme conditions. The formation of refractory metal coatings by thermal spraying is associated with two major challenges: 1) particles of materials having high melting temperatures should be heated to reach a semi-molten or a molten state; 2) oxidation of the metals should be prevented. In this work, the CCDS2000 detonation spray system was used for obtaining molybdenum and tantalum coatings. The coatings were deposited on steel substrates at O 2 /C 2 H 2 =1.1 and stand-off distances of 20 mm and 100 mm. The calculation of the particle temperatures and velocities were carried out to find the optimal spraying modes for Mo and Ta powders. No oxide phases were found in the coatings obtained by spraying of the Mo powder. In the Ta-based coatings, Ta 2 O 5 was found as a second phase. The hardness of the Mo coatings sprayed at 20 mm and 100 mm was 500 HV 300 and 625 HV 300 , respectively. The porosity of the Mo coatings was less than 0.5% for both stand-off distances. The hardness of the Ta-based coatings sprayed at 20 mm and 100 mm was 800 HV 300 and 1000 HV 300 , respectively. The porosity of these coatings was less than 1% for both stand-off distances. The bond strength of the Mo coatings determined by the pin test method was 92 and 126 MPa and that of the Ta-based coatings was 43 and 77 MPa, for coatings deposited at 20 and 100 mm, respectively.

In twin wire arc spraying process it is possible to use feedstock wires of two different compositions at the same time. As a result of this procedure it can be achieved composite coatings called also as pseudo alloys with modified physical properties. In this study nickel and cobalt based super alloy materials were arc sprayed with pure molybdenum wire to tailor corrosion and wear resistance of the coatings. Coatings for the tests were sprayed using two different twin wire Sulzer Metco arc-spraying units, Smart Arc and OSU 300, operating with suitable spray parameters to produce coatings of good quality. It was already known that these twin wire configurations are producing coatings with differing microstructures. Coating sprayed with the OSU system was clearly finer in structure and one purpose of this study was to measure the effect of the micro structural size on the corrosion and wear properties of the final coatings. Microstructures of the coating materials were studied and analyzed from cross-sectional specimens. Volume fraction of pure molybdenum in the coating matrices was evaluated with simple line method and according to the results volume fraction of pure molybdenum metal is over 50 volume-% in all of these tested composite coatings and higher in materials sprayed with OSU unit. Also the microstructure of the coatings was seen to be finer when OSU was used as was expected. Wear resistance was measured with modified ASTM G65 rubber wheel sand abrasion wear test and corrosion resistance was tested in low pH values and chlorine containing environment according to the ASTM G48 corrosion testing standard. Corrosion testing was carried out at room temperature 22°C and also at higher 50°C temperature. Molybdenum addition is clearly improving the abrasion wear resistance of the tested coating systems. At room temperature also the corrosion resistance is getting better with molybdenum addition but at higher temperature this effect is not so clear.

In-flight particle temperature measurements during atmospheric plasma spraying (APS) of Tungsten, Molybdenum, and Yttria stabilized Zirconia by two-color pyrometry are analyzed statistically. The particle temperature distributions allow assessing the melting status of the particles. Particularly the melting temperature and the particle fractions being still molten or already solidifying can be identified. Furthermore, the relevant systematic and material dependant sources for measurement errors using two-color pyrometry are investigated. Their influence is estimated and corrected best possible. As far as there is reliable data available on the emissivity of the powder material there is good agreement between the corrected measured melting temperatures and reference data.

There have been recent efforts to expand the thermal spraying capabilities for novel corrosion resistant coatings for metal bipolar plates were produced by thermal spraying for proton exchange membrane (PEM) fuel cell applications. Recently, substrate heated by plasma gun or by external laser beam has been proposed to enhance the mechanical and thermal properties of the coatings. Studies were found that with sufficient substrate heating, substrate melting may happen. When droplets solidified on a thin liquid layer on the top of the substrate, conditions will be similar to crystal growth and Epitaxy film growth will be possible. It is therefore possible that using substrate melting as tool to promote epi-layer growth using plasma spraying. Difficulty is how to control the substrate temperature to cause substrate melting during droplet solidification. In this study we will propose a new idea for better temperature control on the substrate. The capability of epitaxy growth using thermal spraying will be investigated. Molybdenum droplets impact on an Aluminum substrate will be studied. A splat formation model including undercooling, nucleation, and non-equilibrium solidification will be used to study the possibility of the substrate melting and grain size distribution.

A numerical study has been conducted on yttria stabilized zirconia and molybdenum splat cooling taking into account the effects of various parameters. In particular, the effect of the splat thickness, the splat/substrate interface thermal resistance, the latent heat of solidification and the substrate initial temperature on the solidification occurrence and kinetics have been studied. A two-dimension model of heat transfer taking into account the phase change during rapid solidification with an enthalpy formulation has been used for these calculations.

Molybdenum splats were produced at three plasma conditions on steel substrates preheated to three temperatures. Morphology of splats and corresponding craters formed on substrates were observed; dimensions of splats and craters were measured with an optical non-contact interferometer. It is found that substrate is significantly melted and deformed upon impact of the droplet, which leads to the formation of flower like splats and craters. On average, only about 36 to 53 % of the areas covered by splats were in good metallurgical/mechanical contact with substrate. Normalized crater volume increases with droplet size and the contact is improved for the high particle energy/high substrate temperature condition as compared with low particle energy/medium substrate energy condition. Splat morphology and crater formation is explained based on impinging jet heat transfer model.

Wire flame sprayed molybdenum is a wide used procedure for manufacturing of wear resistance coatings. The properties of thermal sprayed coatings depend mainly on the kinetic and thermal energy of sprayed particles, i.e., a higher particle velocity causes an increase of coating quality. The now available high velocity spray system from Praxair which is used within this work is capable to realise the aim of high particle velocities. The coating properties presented in this work are analysed in comparison to conventional wire and powder plasma spray processes. HVWFS molybdenum coatings show lower porosity, higher adhesion and cohesion and better wear properties. To explain the results, particle size distribution, oxygen/carbon content and structure are analysed. Hardening mechanisms of coatings and their adhesion/cohesion properties are discussed based on light microscopy, SEM, XRD and TEM investigations.

A numerical model is developed to study the effects of the contact resistance, droplet impacting droplet temperature, and substrate temperature on the droplet solidification rate and temperature of the droplet under the condition when the substrate can melt and re-solidify. Two-dimensional simulations show that the interface velocity is small in the area of poor contact with an irregular solidification interface shape. During the impact of Molybdenum on a steel substrate, Mo solidifies while the steel substrate melts.

Stainless steels such as AISI Type 304 SS are being used for seawater piping applications due to their desirable mechanical properties and good weldability. However, they are susceptible to pitting and crevice corrosion in chloride bearing environments. Thus a new generation of highly alloyed stainless steels such as Avesta 254 SMO with high molybdenum contents has been developed for improved localised corrosion resistance in seawater. These steels are also susceptible to the formation of undesirable secondary phases such as sigma and chi which degrades both mechanical and corrosion properties. Alternatively, the main alloying element can be surface alloyed onto the surface of a suitable substrate by laser surface alloying. In this paper, austenitic stainless steel surface alloys of varying molybdenum contents have been formed on 304 SS by laser surface alloying and characterised by optical and scanning electron microscopy. The corrosion behaviour was ascertained by electrochemical and immersion tests.

Plasma sprayed deposits consist of multitude of flattened lamellar particles - 'splats' - which as basic building elements form their structure and determine the deposit properties. Therefore, knowledge of the mechanism of their formation and characteristics is important for understanding the processing property relationships. Although extensive studies have been done on splat formation, there is a lack of correlation to macroscopic deposit properties. Among factors influencing the deposit properties and performance is residual stress, originating from splat quenching and thermal mismatch between the substrate and coating. This phenomenon has been studied mostly on macroscopic level. In the present study, an attempt is made to establish a connection between these two approaches. In the focus of this study is the effect of selected processing variables on splat characteristics, deposit properties and residual stress in a single-splat layer. The processing variables of primary interest were deposition temperature and substrate material. Molybdenum as a representative material of practical interest was used throughout this study. The correlation between stresses and processing conditions is discussed with regards to microstructure and relevant coating properties.

The splashing usually occurs when a droplet impact on a substrate surface during thermal spraying, which results in the formation of splat with irregularly complicated morphology. In present study splats are formed on polished stainless steel substrate surface covered with different organic substances with different boiling points by plasma spraying under different preheating temperature of substrate in order to clarify the factors which control the splashing during droplet flattening in thermal spray process. The droplet materials used are aluminum, nickel, copper, Al2O3 and molybdenum. Three kinds of organic substances used are xylene, glycol and glycerol which are brushed on the surface of substrate before spraying. It is found that when the preheating temperature exceeds 50°C over the boiling point of organic substance brushed on substrate surface the regular disk type splats are formed in the case that no substrate melting occurs by molten droplet. When the flattening of droplet causes the melting of substrate such as the combination of Mo droplet with stainless steel substrate, the preheating of substrate has no influence on splat morphology. The evaporated gas induced splashing and substrate surface melting induced splashing models are proposed to interpret the formation of the annulus-ringed splat.

The structure and morphology of plasma sprayed splats are experimentally investigated using different droplet materials and substrate materials. Droplet materials include aluminum, copper, nickel and refractory metals such as molybdenum and tungsten, and substrate materials include aluminum, stainless steel, and molybdenum plates. The results show that the splashing occurs during the splatting of a completely molten droplet. Most splats formed by droplets molten completely are only central part of the ideal disk type ones, which are defined as the annulus-ringed disk-like splat. It is found that the morphology of such annulus-ringed disk-like splat is greatly influenced by the combination of droplet and substrate materials depending on whether substrate melting occurs. With the combinations of droplet and substrate materials which are of similar thermal properties the splashing of central area of splat tends to occur to present a honeycomb structure at the center of splat. When droplet impacting can cause melting of substrate annulus-ringed splat prefers to present a split type. The flattening ratio of an annulus-ringed disk splat is typically less than 2.

The High-Velocity Combustion Wire Process is a new high-velocity combustion process now being used in the thermal spray industry. This process combines air, oxygen, and a fuel gas to generate a high-temperature, high-velocity plume that is optimum for producing metallic coatings. Analytical studies were conducted to investigate gas and droplet dynamics for the spraying of three different materials: aluminum, stainless steel, and molybdenum. With the relatively low flame temperatures of the process, the feedstock wire is melted by convective heat transfer with no superheating or vaporization of the droplets. When the droplets strike the substrate, their temperature peaks as the high kinetic energy of the droplet is transformed into thermal energy. The conservation equations were solved using the TORCH computer model, yielding the temperature and velocity profiles as a function of location. The PROCESS gas/droplet computer program was then employed to calculate the dynamics of the molten droplets. The results of this modeling was confirmed with process diagnostics. Experimentation included droplet temperature measurements using a two-color pyrometer and droplet velocity measurements using particle imaging velocimetry for the stainless steel material system. The coatings produced in the study exhibit superior quality with high density, high hardness, low oxide content, and high bond strength.