By approaching the glass transition temperature it was possible to realize well quality metallic coatings on two different glasses using Cold Spray deposition, CS. A roughness is introduced on the glass surface and is proportional to the energy deposited. Using the thermal pressure memory effect of glass, Raman spectroscopy mapping allowed determining that the CS introduced a strong heterogeneity of the glass substrate characterized by zones with different cooling rate and residual stress. Using a simplified Eshelby's inclusion approach, it is demonstrated that the residual stress can be in first approximation explained by the introduction of local density fluctuation induced with high cooling rate of micrometric regions related with the impact of the deposited metallic particles.

The Cold spray (CS) is a promising solid-state additive manufacturing method. The interesting physics involved in the CS process including cold, high strain rate, adiabatic and severe plastic deformation results in a unique and complex structure of CS deposits at different length scales that directly determines the properties of the deposits. Therefore process- structure properties (performance) (PSP) linkages explorations are pivotal. Integrated computational materials engineering (ICME) methods in complement with experimental analyses are required to evaluate materials properties and behaviour in PSP links exploration. Finite element modelling is used to simulate the thermomechanical response of materials and evolution of field variables in CS, i.e stress, strain, strain rate, and temperature, at structural scales. Molecular dynamics modellings of nano-particle impact have provided useful insights into atomic-scale phenomena of individual particle impact while the modelling of microstructure evolution in micro and mesoscale has yet to be investigated. In this study, we developed and implemented a thermodynamic phase field simulation method to capture the structure evolution of CS composite Ni-Ti deposit upon post-spray heat treatment (PSHT) in microstructure scale. The external or internal stimuli such as heat and strain either generated in the system because of phase transformation or stored as internal energy upon CS process are accounted for. The interface mobility and microstructure development are calculated by minimization of Gibbs free energy of the system. The comparison of the simulated microstructure with experimental results confirms that the phase field modelling precisely predicts the microstructure evolution of the CS deposits upon PSHT.

In the current work, a NiCrAlY and Fe-based alloy are HVOF-sprayed due to the combination of high coating density and customizable coating properties. The oxygen to fuel gas ratio was varied to modify coating defects in a targeted manner. The results demonstrate material dependent defect mechanisms. Further investigations regarded residual stresses, hardness, and electrical conductivity. In particular, the thermal diffusivity proved to be very promising. Moreover, the coatings were compared with previous work on arc-sprayed coatings of similar chemical composition regarding insulation capability.

The feasibility of processing various polymers by cold spray has been exemplified by depositions with low porosity and properties comparable to the bulk material. However, cold sprayed polymers are generally deposited with low deposition efficiency compared to more extensively studied metal sprays. Low efficiencies in polymer sprays are attributed to characteristic differences in material properties between metals and polymers. Notably, the thermophysical properties of polymers limit heat transfer and promote intra-particle thermal gradients that develop during cold spray processing. These properties (e.g., thermal conductivity, heat capacity, density) and low deposition efficiencies demand alterations to the cold spray process equipment outside typical metal powder spray conditions. Herein, a modified powder feed tube is used to pre-heat powder to temperatures (~84 °C) below the powder melting point, or cool it (~-55 °C) below room temperature before contacting the high velocity carrier gas in the nozzle of a CSM 108 cold spray system. Numerical simulation demonstrated that pre-heating/cooling the powder feedstock is a viable means of adjusting particle temperature upon impact with the substrate; however, this technique has generally not been deliberately utilized in the cold spray of polymers. In the present work, no significant increase in deposition efficiency (~65% for all sprays) was found by increasing the pre-heat temperature. However, pre-heated particles had a mechanical strength 28% higher than particles injected at room temperature and -55 °C. Despite this, scanning electron microscope images indicated no notable differences between the deposit microstructures. Future works are planned to study the effect of pre-heat at higher particle impact velocities and degrees of pre-heat to improve powder consolidation.

High-entropy alloys (HEAs) represent an innovative development approach for new alloy systems. These materials have been found to yield promising properties, such as high strength in combination with sufficient ductility as well as high wear and corrosion resistance. Especially for alloys with a body-centered cubic (bcc) structure, advantageous surface properties have been revealed. However, typical HEA systems contain high contents of expensive or scarce elements. Consequently, applying them as coatings where their use is limited to the surface represents an exciting pathway enabling economical exploitation of their superior properties. Nevertheless, processing conditions strongly influence the resulting microstructure and phase formation, which in turn has a considerable effect on the functional properties of HEAs. In the presented study, microstructural differences between high-velocity oxygen fuel (HVOF) and high-velocity air fuel (HVAF) sprayed coatings of the alloy AlCrFeCoNi are investigated. A metastable bcc structure is formed in both coating processes. Precipitation reactions are suppressed by the rapid solidification during atomization and by the relatively low thermal input during spraying. The coating resistance to corrosive media was investigated in detail, and an improved passivation behavior was observed in the HVAF coatings.

High-entropy alloys are of great interest due to their unique phase structure. They are constructed with five or more principal alloying elements in equimolar or near-equimolar ratios and thus derive their performance from multiple elements rather than one. In this work, solid-state cold spraying is used for the first time to produce a FeCoNiCrMn high-entropy alloy coating. As a low-temperature process, cold spraying completely retained the high-entropy phase structure in the coating without any phase transformation. Examination shows that the grains underwent significant refinement due to dynamic recrystallization and that the coatings are much harder than the feedstock powder because of increased dislocation density and grain boundaries.

The purpose of this work is to study the effect of laser radiation on powder particles transported by gas during laser cladding. The temperature and velocity of particles entering the light field of a CO 2 laser were determined by measuring particle radiation as well as the scattered radiation of the diode laser, two independent methods. It is shown that under the action of laser radiation, the particles acquire additional acceleration due to the vapor pressure from the irradiated part of the particle surface. This sonic recoil vapor pressure can significantly affect the in-flight characteristics of powder particles in a gas jet. Particle velocities due to laser acceleration exceeded 100 m/s in a carrier gas with a flow rate less than 30 m/s. Particle temperature depends on several factors and was found to vary from ambient temperature to the boiling point of the powder.

A wide range of properties can be achieved in intermetallic coatings applied by gas detonation spraying (GDS). The properties of Fe-40at%Al GDS layers, however, may change when exposed to temperatures exceeding a threshold level. To characterize such changes, Fe-40at%Al GDS coatings were subjected to systematic dilatometric studies in which temperatures were cycled from room temperature to 1180 °C. The investigation revealed both irreversible and reversible phase transitions as described in the paper. Dilatometry measurements obtained from sintered samples made from the same powder are presented for comparison.

This study assesses the viability of using nitrogen instead of helium to cold spray NiCoCrAlTaY coatings onto single-crystal superalloy substrates. The process, though feasible, has a low deposition efficiency, leading to a high level of deformation that affects the microstructure of both the coating and substrate. SEM and TEM analysis revealed metallurgical and mechanical bonding at the interface and grain refinement in the coating. A fine grain structure that developed in the substrate after deposition was also observed possibly caused by dynamic recrystallization during the deposition process. Evidence of element segregation in the substrate, identifiable as zones with a deformed γ/γ’ structure, was found as well.

Coatings applied on steel molds used for casting aluminum parts have two main purposes: avoid mold metal reaction and control thermal transfer to obtain directional solidification. The coatings widely known to foundry operators are water-based sodium-silicate bonded ceramic suspensions; they are air sprayed and cured on mold surfaces and typically last for 100 casting cycles. Although thermal sprayed coatings have been shown to last more than 5000 casting cycles, they are not yet the preferred mold protection method. This study addresses the issue by developing a knowledge base of thermal transfer properties that can be achieved with air plasma sprayed magnesium zirconate powders. The properties are assessed on an instrumented mold using the inverse technique for different coating compositions.

This study assesses the influence of atmospheric plasma spraying parameters on splat stacking and porosity formation in bioglass coatings prepared from commercial powders. Coating samples were deposited on stainless steel substrates using spraying parameters established through numerical simulations. Different Ar-H 2 mixtures were used as the forming gas, and plasma current and spraying distance were varied. Coating microstructure and phase composition were determined by SEM and XRD analysis. Although numerical simulations for each parameter set predicted a suitable Sommerfeld number for proper splat stacking, Na 2 O and P 2 O 5 volatilization occurred during spraying, promoting the formation of porosity in the coatings. Denser coatings were obtained, however, by adjusting the gas mixture ratio, plasma current, and spraying distance such that enthalpy of the plasma jet is sufficient to overcome the glass transition temperature of the powder and at the same time avoid the evaporation of volatile oxides.

Strontium zirconate is a candidate material for thermal barrier coatings due to its high melting point, good sintering resistance, and high TCE. One drawback, however, is a phase transition that occurs below 1200 °C , although rare-earth element doping offers a way to suppress it. In this study, SrZrO 3 doped with two rare earth oxides, ytterbia and gadolinia, is deposited by solution precursor plasma spraying and the layers obtained are evaluated before and after heat treatment. The coatings are characterized by two phases, SrZrO 3 and t-ZrO 2 , with interpass boundary structure, nano and microscale porosity, and through-thickness vertical cracks. XRD analysis after heat treatment at 1400 °C for 360 h shows that the two phases are very stable due to the doping of rare-earth elements, which is also shown to reduce thermal conductivity in the as-sprayed deposits by nearly 35%.

Rare-earth complex oxide ceramics are promising candidate materials for next-generation thermal barrier coatings due to their low thermal conductivity and phase stability. During plasma spraying, the component with a higher vapor pressure may experience severe preferential vaporization, resulting in significant composition change from the starting powder. In this study, Gd 2 Zr 2 O 7 (GZO) powder with a hollow spherical structure is used as the feedstock material to assess the vaporization behavior of G d2 O 3 during atmospheric plasma spraying (APS). Isolated Gd 2 Zr 2 O 7 splats with regular disc shapes in different sizes were deposited on stainless steel substrates at a deposition temperature of 300 °C to study the effects of particle size on vaporization loss. The elemental composition of each splat was analyzed by EDS, and the ratio of Gd to Zr in different splats with different diameters was obtained. The results show that the vaporization loss of Gd increases markedly with decreasing particle size due to the preferential vaporization of G d2 O 3 . Using Gd 2 Zr 2 O 7 powders of a certain size can reduce Gd loss, although the effect is determined by molten droplet size rather than apparent powder particle size.

A low thermal conductivity in feedstock material and high plasma temperatures generally lead to inhomogeneous heating of particles in plasma spraying. Existing modeling methods can determine heat transfer within idealized spherical particles with homogenous morphology, but in many cases, particles have an agglomerated morphology, consisting of multiple smaller particles that are packed together. The reduced contact area between the individual smaller particles results in a drastic reduction of the effective thermal conductivity of the agglomerate. On the other hand, it enhances heat transfer from the plasma gas due to the increased particle surface area and penetration of the hot plasma into the agglomerate. Moreover, the momentum transfer from the plasma to the agglomerate differs from that of a homogenous spherical particle, which can significantly affect heating dynamics. This paper presents a novel particle modeling approach that accounts for all such phenomena. Differences in kinematics and heating dynamics of the agglomerates are analyzed with regard to their packing densities.

While depositing Fe-Al intermetallic powders applying a gas detonation spraying a certain coating structures containing oxide ceramics are created. These structures exhibit both extreme mechanical resistance and unusual thermophysical properties (TP) also. One of such property is relatively low thermal conductivity. A possible application as thermal barrier coatings needs precise determination of TP dependence on temperature and resistance of the coating structure to temperature exposition. At present study TPs were investigated for a coating produced from Fe-Al intermetallic powder in a course of complex measurements including DSC analyses, laser flash thermal diffusivity measurements, dilatometric studies complemented with microstructural analyses. The study resulted in full characterization of the investigated structure TPs: density, thermal expansivity, heat capacity and thermal conductivity. During thermal analyses interesting phenomena concerning thermal resistance to the temperature exposition of the investigated coating were revealed. The obtained results complement rather sparse literature data on TPs in that subject and contribute to better understanding of gas detonation spraying (GDS) process technology and intermetallic/oxide structures property understanding.

High temperature and fire-proof protection of metal structures issue involves formation of dense insulating coatings which possess low thermal diffusivity and capable to withstand high temperatures caused by open flame and other severe conditions. Such coating should be considered as sacrificial as it slowly decomposes during extreme high temperature impact. Such coatings intend significant extension of time required for heating and development of inelastic deformation in metal-based structures increasing service time in severe conditions. Several modifications of fire-proof coatings composed of organic binders were developed and investigated. Fireproof coatings were subjected to open flame test on an adapted burner rig. Open flame simulation with 1100°C was carried to estimate coating’s protection properties. Investigates coating showed reduction of temperature for 1000°C during 10 minutes. Such results achieved due to spumescent effect of coating’s coke layer.

In this study, the effect of the substrate roughness and thickness on the heat transfer coefficient of the impinging air jet upon a flat substrate was investigated. A low-pressure cold spraying unit was used to generate a compressed air jet that impinged on a flat substrate. A detailed mathematical model was developed and coupled with experimental data to determine the heat transfer coefficient and surface temperature of the substrate. It was found that increasing the roughness of the substrate enhanced the heat exchange between the impinging air jet and the substrate. As a result, higher surface temperatures on the rough substrate were measured. It was further found that the Nusselt number that was predicted by the model was independent of the thickness of the substrate. The results of the current study were aimed to cover the influential substrate parameters on surface temperature of the substrate that eventually can affect the final quality of the cold-sprayed coatings.

Plasma Spray Physical Vapor Deposition aims to substantially evaporate a powder in order to produce coatings with microstructures ranging from lamellar to columnar. This is achieved by the deposition of fine melted powder particles and nanoclusters and/or vapor condensation. The deposition process typically operates at pressure ranging between 10 and 200 Pa. In addition to experimental works, numerical works help to better understand the process and optimize the experimental conditions. However, the combination of high temperature and low pressure with the appearance of shock waves resulting from the supersonic expansion of the hot gas in the low pressure medium, makes questionable the suitability of the continuum approach for modelling such a process. This work deals with the study of (i) the effect of the pressure dependence of the thermodynamic and transport properties on the CFD predictions and (ii) the validity of the continuum approach for thermal plasma flow simulation under very low pressure conditions. It compares the flow fields predicted with a continuum approach (ANSYS Fluent CFD code) and a kinetic-based approach using a Direct Simulation Monte Carlo method (DSMC, SPARTA code). It also shows how presence of flow gradients can contribute to the errors in the results for typical PS-PVD conditions.

High-purity nanocrystallized YSZ powders were used to manufacture thermal barrier coatings by air plasma spraying. After spraying, the coating samples were aged at temperatures of 1200, 1300, and 1400 °C. Coating samples made from ordinary YSZ powders were aged at the same temperatures. XRD analysis shows significant tetragonal-to-monoclinic phase transformation in the reference coatings after 100 h at 1400 °C in contrast to the phase stability exhibited by high-purity YSZ. The sintering behavior of the YSZ coatings was also examined along with the influence of MCrAlY oxidation.

In this work, atmospheric plasma spraying was used to deposit an equiatomic AlCoCrFeNiTi high-entropy alloy (HEA) coating with a thickness of 236 μm, a porosity of 1.6%, and an adhesive strength of 50.3 MPa. The as-sprayed coating mainly contained BCC1 and BCC2 phases, with only a trace amount of the FCC phase. Microhardness was four times that of 316 stainless steel and the volume wear rate at room temperature was one-fourth that of the substrate material. The wear rate decreased with increasing temperature from 25°C to 700°C, then increased from 700°C to 900°C. Over that range, the wear mechanism changed from delamination wear to oxidation and adhesion wear.