Metal surface characteristics play a significant role in interacting with their biological environment. Copper surfaces have been identified for their antimicrobial properties. Improvement of antibacterial and antiviral performances can be tailored by surface microstructure modification. Severe plastic deformation is an effective surface modification procedure to improve the mechanical performance of metal surfaces. This technique can be adapted to obtain surface grain refinement and induce surface roughness. In this work, cold spray shot peening is used to modify copper substrate surfaces and study the effects on their antibacterial properties. To modify the grain structure of copper, different shot-peening parameters were examined. The surface roughness and microstructure were investigated by employing optical and scanning electron microscopy. The bactericidal activity of copper substrates after shot peening treatment is discussed and a comparison between the bacterial load on treated (shot-peened surface and cold sprayed copper coating) and untreated surfaces (as-received) is provided. Testing of the surfaces after their exposure to the biological environment demonstrated improved microbial inactivation performances for surfaces that had undergone grain refinement without exceeding a certain roughness value.

In this work, a new cold-spray shot-peening process was used to achieve surface nanocrystallization on a magnesium alloy deposit. The results of various examinations and tests show that nanocrystalline layers up to 40 µm thick with an average grain size in range of 50-80 nm can be prepared on AZ91D deposits using the new process. The nanocrystalline layers also exhibit good microhardness and tribological properties.

In this study, pure Al coating was deposited via in-situ shot-peening-assisted cold spray method in order to study the effect of the in-situ tamping effect which was caused by the impact of large sized shot-peening particles on grains size evolution of coatings. The microstructures of the as-sprayed Al coating were observed by using Scanning Electron Microscope and Electron Backscatter Diffraction. A commercial gas atomized Al powder with a grain size range of 10-20 μm was used as the spraying powder. The cross section of the as-sprayed Al particles presented elongated rectangular morphologies, which indicated that the nearly spherical particles experienced severe plastic deformation by the impact of large sized shot-peening particles. It was found that dynamic recrystallization of dislocations-ridden regions was responsible for the grain refinement of cold sprayed coating. Aluminum grains with size of several tens to several hundred of nanometers can be apparently recognized at the whole cross section of the particle. Therefore, in-situ shot-peening-assisted cold spray method can deposit completely nanocrystalline coating using micrometer-grain powder, and thus can be employed to develop high quality coatings of commercial importance.

Three Fe-based powder alloys, Höganäs Fe SP529, Fe SP586 and 6AB, have been deposited by HVOF and HVAF spraying onto mild steel plates. The sprayed samples were first ground and then shot peened using glass shot in order to seal the surface interconnected pores and other surface imperfections. The samples as ground and ground/glass shot peened were tested by salt spray (fog) exposition for 238 h according to ASTM B117/ISO 9227. FeSP586, HVOF and HVAF sprayed and glass shot peening samples achieved surface sealing enough to pass the test with appearance rating RA = 9 according to ISO 10289. All other samples achieved moderate to excessive pitting and/or moderate to excessive staining types of corrosion defects.

In this study, pure Al coatings were deposited on ZK60-T5 Mg alloy substrates via in-situ shot-peening assisted cold spray in order to study the effect of the Al coating on fatigue behavior of coated samples. Fatigue behavior of the coated and un-coated samples has been investigated through experimental tests. The size and shape distribution of powders, microstructural characteristics of coatings and fractography of fatigue test samples have been studied using scanning electron microscopy. The average microhardness of pure Al coating is higher than 70 HV50. In order to obtain the fatigue S-N diagram for each set, coated and un-coated samples have been tested in a load-controlled condition. The tension-compression fatigue experiments reveal that the fatigue property of ZK60-T5 alloy coated with pure Al coatings has significantly deteriorated compared with un-coated samples.

NiCoCrAlY coatings are widely used as bond coats for ceramic thermal barrier coatings (TBCs) and oxidation and corrosion protective overlay coatings in industrial gas turbines. High temperature oxidation behaviour of NiCoCrAlYs has a great influence on the coating performance and lifetime of TBCs. A promising route to decrease the oxidation rate of such coatings is post-coating surface modification which can facilitate formation of a uniform alumina scale with a considerably slower growth rate compared to the as-sprayed coatings. In this work, the effect of surface treatment by means of shot peening and laser surface melting (LSM) on the oxidation resistance of high velocity air-fuel (HVAF) sprayed NiCoCrAlY coatings was studied. Isothermal oxidation was carried out at 1000 °C for 1000h. Results showed that the rough surface of as-sprayed HVAF sprayed coatings was significantly changed after shot peening and LSM treatment, with a compact and smooth appearance. After the exposure, the oxide scales formed on surface-treated NiCoCrAlY coatings showed different morphology and growth rate compared to those formed on as-sprayed coating surface. The oxidation behaviour of surface treated HVAF-sprayed NiCoCrAlY coatings were revealed and discussed.

This study demonstrates a novel method for improving the corrosion resistance of cold sprayed Al6061 coatings. Large stainless steel particles were added to a commercial Al6061 powder and the mixture was deposited on Mg alloy AZ31B substrates using nitrogen gas at low working pressure and temperature. It is shown that the stainless steel particles had a shot-peening effect, thus increasing the density as well as the corrosion resistance of Al6061 coatings. SEM examination showed that no stainless steel particles were incorporated in the coating.

In this study, in-situ shot-peening approach was introduced by mixing large stainless steel (SS) shots with diameters over 150 μm with IN718 spray powders to aim at developing a novel approach to achieve dense coating. Effect of mixed stainless steel shot content on the microstructure and mechanical properties of the IN718 coating was examined. Results show that IN718 coating can be deposited without any shot peening particle inclusions for their relatively low velocity. It was revealed that the deposition efficiency of the IN 718 powders is improved by the in-situ shot peening effect. With increasing shot fraction in the powder mixture from 0% to 50 vol.%, the coating porosity decreased from 5.6% to 0.2% only by using N2 accelerating gas. Remarkable work hardening induced by impact of the shot peening particles was detected.

The HVOF process is characterized by the deposition of a low porosity and oxide content coating and the particles projected by this process have high kinetic energy, resulting in a high density coating. However, the presence of non-melted particles can affect the porosity, tensile adhesion, hardness and surface finishing. In this article, the influence of the shot peening treatment on morphology, porosity, tensile adhesion and roughness of some FeMnCrSi(Ni/B) HVOF coatings have been studied. High carbon steel particles with spherical geometry were used for shot peening. The results show that the shot peening reduces the porosity, mainly in the coatings with higher porosity level, and generates an increase of hardness with no phase transformations. The increase in adherence is also a benefit generated by the treatment. The surface quality analyses show a significant roughness reduction. With shot peening a compressive residual stress state was achieved in the coating, improving mechanical properties.

This study evaluates the influence of shot peening on the fatigue life of cold spray aluminum alloy 6082 coatings. A pneumatic blast machine with standard steel shot was used to peen both uncoated and coated substrates. Six test groups representing different treatment protocols were characterized in terms of residual stress, roughness, and rotating bending fatigue. The results show that the best fatigue performance is obtained by intense shot peening prior to cold spraying. Post-treatment shot peening, in contrast, had a detrimental effect as a large portion of the kinetic energy is absorbed in the coating, resulting in surface damage rather than further work hardening.

Fundamental properties of Titanium coating prepared by low temperature HVOF process aided by injection of water had been published by our research group. The results showed that low temperature HVOF process provided as a good means for the deposition of comparatively dense Ti coating, however the interconnected pores observed in Ti coating degraded corrosion resistance of Ti coating, therefore it was necessary to manufacture denser Ti coating. Two processes were respectively applied for the densification of Ti coating. One process was to perform post heat treatment for as-sprayed Ti coating with conventional Ti powder as feedstock. The other process was to modify thermal spray powder. Ti powder mixing with spherical glass powder was used to deposit denser Ti coating as a result of shot peening effect of hard glass powder. Finally the corrosion resistance for densified Ti coatings was evaluated by electrochemical characterization.