Tantalum and silver are recognized for their outstanding biocompatibility and antibacterial ability, respectively. However, owing to their distinct chemical and physical properties, synthesizing alloys and composites by using Ta and Ag presents a considerable challenge. In this study, Ta-Ag composites, exhibiting good antibacterial ability, were successfully produced by using a solid-state cold spray technique. Notably, intriguing correlations were observed between Ag microstructure and antibacterial ability. To unravel this correlation, a comprehensive experimental and simulation analyze were conducted. It is found that the volume ratio of Ta to Ag in the feedstock powder result in different deformation histories for Ag during the cold spray process. This, in turn, leads to the formation of distinctive Ag microstructures within Ta-Ag composites. The varied Ag microstructures results in different Ag dissolution ability and the formation of an insoluble AgCl layer exhibiting varying morphologies, when Ag exposed in a high chorine ion environment, like in human body fluids. This consequently influences the concentration of Ag ion and ultimately determines antibacterial ability. The study demonstrates that Ag release rate and the related antibacterial properties could be alternatively controlled by changing Ag contains or by creating different deposition process by adjusting CS parameter.

In biomass boilers, corrosion is a prevalent concern that arises at high temperatures. This is mainly because the fuels consumed in these boilers have a high alkali, chlorine, and other molten salt content that has occasionally led to material depletion, leaks, and unforeseen plant shutdowns. Applying protective coatings using thermal spray techniques is a practical answer to this issue. The current work focused on applying powders of Inconel 625 and Inconel 718 to boiler steel using a high-velocity oxy-fuel spraying method. The samples after coating deposition were subjected to the conditions of a biomass-fired boiler for 15 cycles to study the performance of the coatings in a real environment. The decrease of thickness over time was used to evaluate the erosion-corrosion process. Various characterization techniques were used to examine the as-sprayed and eroded-corroded specimens. The X-ray diffraction (XRD) technique was utilized to analyze the phases, while the surface characteristics of powders, coatings, and samples exposed to erosion-corrosion were investigated through scanning electron microscopy (SEM) combined with energy-dispersive X-ray spectroscopy (EDS). When exposed to the actual boiler environment, the findings showed that Inconel 625-coated steel performed better than Inconel 718-coated steel.

Erosion-corrosion is a severe problem observed in the coal fired thermal power plant boilers which lead to premature failure of boiler tubes. Thermal spray coatings have been applied successfully to check the erosion-corrosion of boiler tubes. In the present research work NiCrTiCRe coating powders were successfully deposited on T22 boiler steel by two different coating processes i.e. high velocity oxy-fuel (HVOF) and cold spray process. The performance of the coatings in actual power plant boiler were investigated and compared. The uncoated and coated T22 boiler steels were subjected the superheater zone of the coal fired boiler for a total of 15 consequent cycles. The thickness loss data and weight change analysis were used to establish kinetics of the erosion-corrosion. X-ray diffraction, surface field emission scanning electron microscope/energy dispersive spectroscopy (FE-SEM/EDS) techniques were used in the present work for the analysis. The results of thickness loss data indicated that the cold sprayed coating performed better in thermal power plant boiler environment.

Titanium porous transport layers (PTL) are important components in proton exchange membrane water electrolysis (PEMWE) cells. The performance enhancement and the reduction of manufacturing cost of PTLs are of importance for market expansion of PEMWE. Vacuum plasma spraying (VPS) was used to prepare PTL or modify PTL of sintered titanium powders and the PTLs by VPS showed a high performance. Regarding the cost efficiency, it is of great interest to produce PTLs using more economical spray processes than VPS. In this study, high velocity oxy-fuel spraying (HVOF) was used to produce highly porous titanium coatings for this purpose. The spray process was developed to achieve a high porosity of up to Φ = 30 % using three titanium powders with size distributions of fA = -90 +45 μm, fB = -63 +20 μm and fc = -45 +11 μm. The coating structures were examined on the cross sections of the titanium coatings with scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The porosity was determined using the image analysis system ImageJ. The deposition efficiency of the titanium powder fC = -45 +11 μm was determined. The results show that the coating structure significantly depends on the titanium powders. Highly porous titanium coatings of Φ = 24 - 40 % can be produced with the titanium powders of fB = -63 +20 μm and fc = -45 +11 μm. Titanium oxides are hardly visible on the cross-sections of the titanium coatings. A high deposition efficiency of approximately DP ≈ 70 % was measured for the titanium powder of fc = -45 +11 μm.

This work focuses on the laser cladding process and the behavior or interaction between the powder particles and the laser beam, specifically examining how various process parameters might affect the creation of melt pool formations. The experiment focused on examining the influence of laser intensity and other important factors on the amount of metal in the substrate of 316L stainless steel, particularly while utilizing Inconel 625 powder. The study was conducted by utilizing cross-sectional images and quantifying the ratio of areas of the melted substrate material across a sliced cross-sectional area. The study also investigated the influence of recirculation patterns resulting from the Marangoni convection force on the formation of the melt region. The study's results indicate that a low powder feed rate is preferable, which in this study was 5 g/min, and provides better results with a symmetrical and profound melt profile. The melt shifts to asymmetrical profiles when the feed rate increases significantly over this value. The primary cause of this phenomenon is attributed to the Marangoni forces and the momentum transfer generated by the powder jets. The investigation also emphasizes the complex interplay among the process factors and highlights the crucial role of laser source power in triggering a fast escalation in the volume of melted material. In addition, the study supports the idea that maintaining the laser energy input as a constant helps to create a consistency in the total melt area even when the cladding speed is increased.

In glass mold industry, a surface treatment by laser cladding of a Ni based powder on cast iron is performed with a 4-kW continuous diode laser. For this, a robot programming method named "Wavering" was used. This method allows to cover large surfaces (higher than 5 mm). The cast iron substrate used during this work is employed for its heat exchange properties in glass mold Industry. However, it has drawbacks which are weak wear, corrosion, and abrasion resistance. Conventional techniques used to protect the molds, like Plasma Transferred Arc (PTA), affect the molds microstructure, but also the thermal and mechanical properties. The laser cladding of the Ni based alloy allows to protect the molds without affecting the cast iron thermal properties (and reduce the Heat Affected Zone length). The purpose of this research is to produce a well bonded Ni based melted powder without pores or cracks on large and curvilinear surfaces with the wanted geometry. The impact of the process parameters such as laser power, scanning speed and frequency on the coating geometry was investigated with an experimental design technique using the ANOVA (Analysis of variance) method. It was used to determine and represent the influence of each process parameter on the coating geometry (width, height, and circularity). This ANOVA analysis led to a parameter combination to optimize the Ni coating and the cast iron substrate quality by considering the industrial geometrical constraints. The bonding quality and the cracking behavior are also investigated on optimized parameters. Finally, it appears that laser cladding process leads to a better coating on curvilinear surfaces than other process like PTA.

Thermal spray (TS) technology has attracted the attention of numerous industrial sectors due to its apparent simplicity and versatility. It has been used across the world for over 80 years in the conservation and creation of art. Despite the creativity involved in the creation of an art piece, the TS artistic endeavors are limited and insufficiently explored. Unique material combinations, usually not observed in conventional engineering applications, can be achieved with TS technology. Although the material amalgamation possibilities are infinite, their combined deposited characteristics, interfacial compatibility and color palette require further study. In this work, the fields of photography, image processing and TS are combined to produce a large art-piece using the cold gas dynamic spray (CGDS) process. Aluminum, zinc, nickel, alumina, steel and titanium alloy powders are sprayed to replicate in three-dimensions a photograph of a crinoid from the Silurian period found on the Anticosti Island, located in the Gulf of St. Lawrence in Canada. The numerous steps required to produce the artistic 3D piece, namely numerical segmentation of the photograph, conversion to a computer-assisted design (CAD), manufacturing of steel masks and CGDS deposition of the selected powders to reach the sought color palette are described. Powder deposition efficiency, material compatibility and microstructural characteristics are analyzed. and the resulting art piece is presented.

Thick deposits were produced from pure Al powder of three different sieve sizes using cold spraying at the same process parameters. The in-plane mechanical and fracture properties of the deposits were investigated using bending of small specimens in four specimen orientations. It was shown that increasing the Al particle size by approximately 50% and 100% leads to small, but statistically significant differences of yield strength. Further, the increase in the powder particle size led to higher fracture toughness K IC but lower fatigue crack growth threshold ΔK thr . This can be attributed to two different fracture mechanisms in the cold sprayed deposits. A trans-particular fracture in the near-threshold fatigue regime is controlled by the microstructure and work hardening of the particles. At higher cyclic loads and in quasi-static regime, the particle decohesion and the resulting crack path determine the fracture behavior instead. However, the observed effect of particle size was rather small, much smaller than the effect of spray process parameters observed in the previous research.

Plasma spraying is the most versatile coating process for depositing a wide range of materials to enhance material performance in harsh conditions. However, severe oxidation during the plasma spraying of metal coatings often results in coatings with high oxide content, limiting interlamellar bonding. Consequently, as-sprayed metal coatings offer inadequate protection against severe corrosion and wear. To address this challenge, we developed Ni-, Cu-, and Fe-based materials containing boron as a deoxidizer. This innovative approach effectively suppresses in-flight oxidation, producing oxide-free molten droplets and enabling the formation of bulk-like metal coatings with sufficient metallurgical bonding between splats. We employed a modified tensile test to evaluate the adhesive and cohesive strengths of these coatings. The Ni-based coatings exhibited adhesive strength exceeding 150 MPa on Fe-based substrates, while cohesive strength surpassed 260 MPa with a novel bond coat. Corrosion and gas penetration tests confirmed the creation of dense, bulk-like Ni-based alloy coatings, demonstrating their potential for various applications in severe service environments.

To achieve higher engine combustion efficiency while reducing emissions, it is necessary to address the challenges posed by elevated operating temperatures. High Entropy Alloys (HEAs) have emerged as promising materials for this purpose, offering exceptional properties at high temperatures, including synergistic effects and excellent resistance to oxidation and corrosion. In this study, a FeCoNiCrAl HEA was investigated as a bond coat material due to its excellent balance of strength and ductility, coupled with outstanding oxidation resistance. It was deposited using HVAF M3 and i7 guns equipped with different nozzles/powder injectors and pressures. Notably, this research marks the first study of the i7 gun globally for the HEA bond coat, coupled with the optimization of HVAF parameters for both i7 and M3 guns. Characterization of both powder and as-sprayed samples was carried out using X-ray Diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDS), and Field Emission Scanning Electron Microscopy (FESEM) techniques. The results revealed the formation of a dense and homogeneous microstructure. Additionally, isothermal oxidation tests were conducted to analyze the behavior of the thermally grown oxide. After 50 hours at 1000 °C, a dense, uniform, and thin alumina TGO layer was observed to have formed. These tests revealed that FeCoNiCrAl HEA exhibits significant potential to enhance oxidation resistance at high temperatures.

An optimized powder/suspension based atmospheric Plasma Spray (PS) process, using a Triplex Pro 210 TM torch, was implemented to elaborate Cu:TiO2 surface coatings on stainless steel. Nanometric Degussa P25 TM powder was prepared in a water-based suspension and co-sprayed with a Cu spheroidal powder. The bacterial reduction, evaluated with 1h-exposure to Escherichia Coli (E. Coli), was two times higher for the Cu:TiO2 coating compared to the bare stainless steel substrate. Since the coatings obtained by plasma spray are relatively porous, their antibacterial efficacy was compared to smooth Ag and Cu doped titanium nitride (TiN) films obtained by physical vapor deposition technique (PVD). For the same exposure time, the PVD smooth coatings showed a much lower antibacterial efficacy proving the topography effect on bacterial adhesion.

Cold spray is an emergent sold-state manufacturing process based on high-speed consecutive collision of small sized particles powders. Such a cold process principle led to the recent development of coatings for various surface functionalization and direct component manufacturing applications. This study investigates the mechanisms of porosity formation during the additive growth of Al1050 powders. To this end, a thermo-mechanical computational model based on the Eulerian computational approach using the Johnson-Cook constitutive law is applied on the case of an additive growth from a stacking of powder layers. The model uses in-flight velocities measured by a DPV2000 system during a cold spray test and an isentropic gas flow model. The measurements show the velocity distribution within the powder jet at the nozzle exit and consists of a Gaussian-like distribution within the typical range of 450-650m/s. The centerline zone at the nozzle exhibits the highest velocity. These data used as input data of the model allowed to apprehend some circumstances of pore formation, in terms of site occurrence, pore behavior over time, and deficient in-flight velocity.

Thermal-sprayed coatings have been extensively used in aerospace with the main purpose to overcome critical challenges such as abrasive wear, corrosion, and erosion under high temperatures and pressures. Such protective coatings can also play a crucial role in optimizing the efficiency of gas turbine engines and therefore in reducing fuel consumption and CO 2 emissions. CuAl-based thermal sprayed coatings are commonly employed in tribological interfaces within gas turbine engines to improve the fretting wear resistance. These coatings are typically deposited by more traditional thermal spray techniques such as Air Plasma Spray (APS), which can result in high amounts of oxidation within the coating. The main purpose of this study is to critically evaluate lower temperature deposition techniques such as High Velocity Oxygen Fuel (HVOF). More specifically, commercially available Cu-10Al powders were deposited by APS and HVOF and compared in terms of their microstructural, mechanical properties, and tribological behavior at various temperatures. The results showed that the friction coefficient for both coatings was equivalent at room temperature while it was lower for the APS coating at high temperature. Similarly, the specific wear rates showed little difference between the different deposition processes at room temperature while the APS coating had a lower wear rate at elevated temperature when compared to the HVOF coating. The differences in the friction and wear behavior were attributed to differences in the interfacial processes.

Infection caused by bacterial contamination is a critical problem challenging the successful use of medical implants in orthopaedic and dental applications. Consequently, medical implants with antibacterial abilities are in high demand. Tantalum and silver have been previously characterized to have excellent biocompatibility and antibacterial ability, but due to their significantly different properties, it is challenging to manufacture Ta-Ag components via thermal processing methods. Herein, by taking advantage of the unique characteristics of cold spray (CS) technology, an antibacterial Ta-Ag coating was successfully fabricated for the first time. In the CS process, blended Ta-Ag powders with different Ag concentrations were used to fabricate CS Ta-Ag coatings. Their antibacterial ability was preliminary tested and deposition behaviour was systematically investigated. The coating significantly reduced the metabolic activity of S. aureus bacteria, and a better deposition efficiency was obtained by blended Ta-Ag powder. It was found that soft Ag could aggregate in the coating and hard Ta particles were prone to rebound, which induced the peening effect for Ag and mass loss of Ta in the final coating Moreover, the clue of metallurgy bonding between Ta and Ag was detected in the region that experienced severe deformation despite their immiscibility.

A new challenge in the transport systems concerns with improving efficiency. Thermal swing coatings are interesting candidates for internal combustion engines due to their potential to reduce cooling requirements and increase efficiency. K 2 Ti 6 O 13 (KTO) thermal barrier coatings (TBCs) were prepared by atmospheric plasma spraying through powder structure design and optimization of deposition conditions. The thermophysical properties of plasma-sprayed KTO deposits and their effect on the thermal swing have been investigated. Their thermal conductivities were tested by a laser flash method and the thermal performance of the coatings was further examined by thermal swing test. The phases, nominal chemical compositions and microstructure of KTO deposits were characterized by X-ray diffraction (XRD) and scanning electron microscopy combined with energy dispersive spectrometry (SEM-EDS). The results indicated that the chemical composition change occurs to the coatings resulting in a deviation from nominal stoichiometry due to chemical reactions between the plasma gas and particles. The thermal conductivity of the coating is very sensitive to the coating compositions, and the coating prepared using porous powder under pure argon presents a single K 2 Ti 6 O 13 phase and high porosity, and the lowest thermal conductivity of 0.85 W/m·K.

Cold spray (CS) is a solid-state process for depositing metal powder, accelerated by a high-velocity gas such that it bonds to the substrate metal through kinetic impact energy. Although the technology is finding applications in non-load bearing repair and coating applications, work is needed in the quality control procedures for CS for its use in load bearing structural applications. in this study, the viability of electrical conductivity and through thickness ultrasound wave velocity measurement methods are studied to serve as a means for nondestructive quantitative measurement methods for quality control in CS and potentially other additive manufacturing (AM) methods. Eddy current, ultrasound, porosity, hardness, and uniaxial tensile strength tests were conducted on copper and aluminum samples that were manufactured using CS. Ultrasound measurements of longitudinal wave velocity and eddy current electrical conductivity measurements showed good correlation with process conditions that were varied to control particle velocity to intentionally produce samples with varying deposition quality. Influence of process conditions on particle velocity was confirmed via particle image velocimetry. Porosity, hardness, and tensile test results were further correlated to ultrasound wave velocity and electrical conductivity measurements. The results of this work show that nondestructive testing methods can be effectively used to quantitatively assess the cold spray products for quality control purposes.

In conventional powder processing, there has been considerable work on classifying feedstock powders based on particle size distribution, morphology, microstructure and composition, since these influence processability and final properties. Cold spray is a new application for powders and conventional characterization may be insufficient to assess powder cold sprayability. In particular, metallic powders have an oxide layer, which breaks during impact with the substrate or with another coating layer during cold spray; this fragmentation facilitates bonding. It has been suggested that the thickness of the oxide layer can influence the mechanism of fragmentation; thicker oxides are easier to remove, revealing clean metal surfaces that can metallurgically bond. Consequently, not all high-purity powders or powders that are stored in ambient conditions have the potential to give good coating properties after cold-spray. This work focuses on surface oxidation of the powders, characterizing the variation of oxide film aspects with size and composition of nominally pure copper powders using X-ray Photoelectron Spectroscopy (XPS). The results indicate the presence of Cu (I) and Cu (II) oxide species on the surface of as-received, naturally aged and heat-treated powders; their thickness is determined using the depth profiling feature.

As it has been demonstrated that the use of the observation equipment applied on the spray process helps to gain a better coating in terms of properties, non-intrusive observation equipment (Control Vision Inc's SprayCam) is used in the current work for the observations of the jet and particles during the spray process. The application of such in-situ observation techniques concerns the field of cold spraying and brings new insights into the formation process of cold sprayed coatings. The build-up of coatings operated with different parameters (copper powder, nozzle, etc.) are recorded with an extreme short unit of time and then analyzed with the help of digital techniques such as image processing. The basic theories on cold spraying were previously verified by simulation and then compared to experimental results considering the distribution of flying particles involving in the build-up of the coating. The accumulation of data collected by in situ processing techniques during the spray allows understanding the complete steps of the coating formation consequently could bring the entire cold spraying mechanism to a higher level of research.

The cavitation performance of wear resistant cermet coatings can deteriorate in a corrosive environment. This investigation therefore considered the cavitation resistance in seawater of thermally sprayed High Velocity Oxy Fuel (HVOF) WC-10Co-4Cr coatings deposited on two different substrate materials of carbon steel and austenitic stainless steel. Coatings were deposited using industrially optimised parameters. Cavitation tests were conducted following the ASTM G32 test method in indirect mode, where there was a gap of 0.5 mm between the sonicator and the test surface. A submersed copper cooling coil controlled the temperature of the seawater. The cumulative cavitation erosion mass loss and cavitation erosion rate results are reported. The eroded substrate and coating surfaces were analysed using Scanning Electron Microscopy (SEM) in combination with energy dispersive x-ray analysis (EDX) to understand the failure modes. Coating phases were identified using x-ray diffraction. Results are discussed in terms of the cavitation failure modes and cavitation erosion rates for both the substrate and coated surfaces.

In high-pressure cold spray, the enthalpy of the particle carrier gas has a significant effect on the propellant gas conditions and ultimately on particle impact velocities and temperatures. Through modelling and experimentation, the current work demonstrates that in low-pressure cold spray, the particle carrier gas enthalpy has a minimal effect on the particle velocity and is rather limited to affecting the particle impact temperature. Consequently, particle impact temperature can be controlled independently from impact velocity. This is a valuable tool when dealing with temperature sensitive substrates: low propellant temperatures can be used in combination with high particle temperatures enabling particle deformation while minimizing substrate heat input. Particle preheating was used to inject pure aluminum particles in a commercial low-pressure cold spray to temperatures up to 500°C. This was accomplished without clogging because of the development of a novel particle preheater, which eliminated the particles exposure to hot metal surfaces. Even after substantial spray time, no evidence of wear or clogging was found. The particle preheating resulted in a deposition efficiency increase of 3.6 times when compared to the injection of room temperature particles.