Quenching in a fluid is a complex process. There are several different heat transfer mechanisms that may be occurring at the same time, with the heat transfer coefficients changes as a function of position (x, y, z) and surface temperature on the same part. This is further complicated by having multiple different parts in the same load. Agitation, racking of the parts and the quench tank design all play a role in the resultant properties and distortion of a given part. Further complicating this problem, is that there are multiple methods to measure quenching performance. In this paper, we will be describing an agitation apparatus used at Quaker Houghton for determining heat transfer coefficients as a function of agitation and surface temperature. The probe used is the ISO 9950 (ASTM D6200) Inconel probe, and the heat transfer coefficients are determined by an inverse method provided by the SmartQuench Integra software by RISE/ivf. The apparatus is examined using Computational Fluid Dynamics (CFD), and the calculated flow is compared to the measured fluid flow.

It is well known that the maximum prior austenite grain size after carburizing heat treatment is approximately positively correlated with the maximum shear strain in the case of simple deformation of pre process as cold working treatment. On the other hand, it is generally known that the maximum shear strain and the maximum grain size do not correspond when complex cold working is performed, but the reason of these phenomena is not well known. Then, it is necessary to investigate the relationship between the applied strain during cold working with multiple steps and prior austenite grain size after heat treatment(GG). In this study, we used a processing method called HPT processing, which introduces shear strain by torsion deformation under applying high hydrostatic pressure to the top and bottom of a disk-shaped sample using a die, and investigated how GG changes due to the accumulation of dislocations by focusing on the strain amount | ± Δ ε| given in one pass controlled by a processing path called Cyclic-HPT (c-HPT) (4) and the total strain amount 𝛴| ± Δ ε| given to the sample by the accumulation of one pass. As a result, when finer strain is applied, the grain size does not necessarily become smaller, but rather there are boundary conditions that indicate the positive and negative grain size with respect to the number of strains. Similarly, for the grain size distribution, an increase and decrease in grain size was observed with respect to radial distance, so there are boundary conditions that indicate the positive and negative grain size with respect to distance. From these results, it is believed that this may be the mechanism for grain growth behavior in the case of cold working, which involves complex deformation.

The aim of the present research work was to investigate tribological performance and potential of Ni-based self-lubricating claddings for high temperature forming of lightweight alloys. Laser claddings included in this investigation were based on Ni-matrix with the incorporation of 5 wt% silver and 10 wt% MoS2 as solid lubricant precursors. Tribological evaluation and testing was performed by Load- Scanner to simulate hot forming process and results compared to high performance hot work tool steel. To simulate hot forming process of forging, wire drawing and extrusion, tests were done at room and elevated temperatures (150°C and 300°C) against typical light-weight alloys, including AISI 316L stainless steel, 6xxx series Al alloy and Ti6Al4V Ti alloy and results evaluated in terms of coefficient of friction vs. load, critical loads for galling initiation and volume of adhered work material. Results show that self-lubricated claddings with incorporated MoS2 and Ag as solid lubricants in general provide lower and more stable friction as well as improved galling resistance in high temperature forming of lightweight alloys. Positive effect of self-lubricating claddings intensifies with forming temperature, degree of plastic deformation and work material tendency to galling.

Induction surface hardening is a process often used in industrial applications to efficiently increase the lifetime of components. Recently, this process has been enhanced with the inductive short time austempering process, creating a martensitic-bainitic microstructure. It is well-known that in homogeneous mixed microstructures, an optimally adjusted volume fraction of bainite can significantly increase the lifetime of the components even further. Regarding inductive short time austempering, there is a lack of knowledge in characterizing and differentiating graded microstructures, which occur due to the temperature gradients within the process. Therefore, three methods were investigated: the analysis of the grayscale profile of metallographic sections, the hardness profile and the full width at half maximum (FWHM) profile from the intensity curve (rocking curve) of the X-ray diffraction pattern. These methods were initially applied to homogeneous structures and evaluated. The findings were then transferred to graded microstructures. Finally, the graded microstructures could be differentiated both via the hardness profile and the FWHM value, while the grayscale analysis only allowed qualitative statements to be made. It became evident that both the volume fractions and their structure are crucial for subsequent mechanical characterization. Since the martensitic microstructure is easier to identify, it serves as a reliable reference for evaluating the mixed microstructure. In summary, these findings offer the foundation for further characterization of graded martensitic-bainitic mixed microstructures.

Martensitic stainless steels are an important group of steels for applications as knives, tools & molds and highly loaded parts in the food and plastics processing industry as well as for machinery components. Their typical hardening consists of quenching and (multiple) tempering (Q&T). As many of these steels contain at least smaller amounts of retained austenite (RA) after quenching, partitioning of carbon and nitrogen from the martensite into the RA can take place during tempering, changing it from Q&T to quenching & partitioning (Q&P). This contribution provides as systematic overview of such partitioning effects on the microstructure like the amount and stability of retained austenite as well as on subsequent effects on material properties such as hardness, toughness, strength and ductility. The various effects were investigated on several steel grades and cover also the effect of variation in heat treatment parameters like austenitizing temperature, quench rate, quenching temperature, number, duration and temperature of the tempering, respectively partitioning. The results clearly show that partitioning dominates over tempering effects at temperatures up to 500°C. Higher quenching temperatures can increase the RA-content similar to higher austenitizing temperatures. Lower quench rates can reduce it due to carbide (nitride) precipitation. Rising tempering (partitioning) temperatures up to 400°C enhances the austenite stabilization. Higher amounts of RA with reduced stability promotes transformation induced plasticity (TRIP), providing the possibility to optimized ductility and tensile strength but reduces yield strength. Increased amounts of RA with sufficient stability increases impact toughness at slightly reduced hardness. Increasing the tempering temperature above 500°C in contrast promotes, after a certain nucleation time, carbide and nitride precipitation, resulting in the elimination of the retained austenite and therefore a typical tempering condition.

Gas carburizing with quenching is one of the most useful heat treatment processes for steel parts. However, after quenching distortion is still occurs. The nitriding and nitrocarburizing are the surface hardening heat treatment methods with low distortion, but these methods require the long treating time to obtain a thick hardened layer. Austenitic nitriding and quenching (ANQ) solves these problems. In ANQ process, nitrogen is infiltrated into the steel parts in austenite phase, and they are quenched to harden. The ANQ process can also be applied to cheap low carbon steel such as the Cold Rolled Carbon Steel Sheet. In this study, the effect of ANQ on mechanical properties was examined. For infiltrating the nitrogen into the steel parts, the steel parts were heating to 750°C or higher in an ammonia atmosphere and heating to 750°C or higher in a nitrogen glow discharge. After the ANQ process, hardness profiles, structure, nitrogen and carbon concentration profiles were observed. Also, distortion, tribological properties, impact value and fatigue strength were examined. The effective case depth, which is treated by ANQ, is larger than the effective case depth of gas nitrocarburizing for same period of time. Distortion of ANQ is much smaller than that of gas carbonitriding, and it is almost equal with that of gas nitrocarburizing. The seizure load is same as with other surface hardening heat treatment processes. The wear loss of ANQ is a lower, in the amount of about 1/2 that of the carbonitrided specimen and 1/3 that of the gas nitrocarburized specimen. The ANQ is an effective heat treatment process for parts which require wear resistance. The tempering softening resistance is improved by nitrogen infiltration. ANQ also improves the impact value and fatigue strength.

Diamond-like carbon (DLC) coatings, which improve wear resistance and extend component service life, have gained considerable research attention as an approach for conserving limited resources. The DLC coating is a highly functional film with high hardness and excellent low-friction, wear-resistance, and corrosion-resistance properties; however, it has high residual stress and low adhesion between the substrate and the film. Existing studies have focused on using DLC containing metallic elements (Me-DLC) as an intermediate layer to minimize residual stress, thereby improving adhesion. Si-DLC is deposited using a mixture of hydrocarbon gases, such as methane (CH 4 ) and acetylene (C 2 H 2 ), and silicon gases, such as tetramethylsilane (TMS: Si(CH 3 ) 4 ), H, and Si, to form the DLC coating. The composition, hardness, Young’s modulus, and friction coefficient of the film can be controlled by changing the composition of the gas mixture. This study investigated the effect of the flow rate ratio of source gases (CH 4 and TMS; C 2 H 2 and TMS) on the properties of the DLC film when Si-DLC is deposited as an intermediate layer on austenitic stainless steel SUS304 using plasma-enhanced chemical vapor deposition. The coating time was adjusted to ensure that the thicknesses of the Si-DLC layer and DLC film were 1.0 and 0.2 μm, respectively, under both conditions. The results demonstrated that the durability of the DLC film improved and adhesion decreased with a decrease in the TMS ratio in the Si-DLC intermediate layer. Durability improved and adhesion decreased when C 2 H 2 was used as the source gas, as compared to when CH 4 was used.

In recent years, physical vapor deposition and chemical vapor deposition (CVD) methods have made significant advancements due to the growing demand for surface modification technologies. This study focuses on depositing diamond-like carbon (DLC) as a thin, hard film using plasma-enhanced CVD. DLC possesses properties such as high hardness, low friction, wear resistance, and chemical stability. However, a drawback is low adhesion caused by residual stress and differences in hardness between the film and the substrate material. Therefore, efforts are underway to improve adhesion by introducing a DLC intermediate layer containing metallic elements to reduce residual stress or by applying treatments to harden the substrate material, such as nitriding or carburizing. Active screen plasma nitriding (ASPN) is a nitriding method that eliminates edge effects and electrically insulates the sample during the process. However, during nitriding, deposits can cover the sample and slow down the nitriding rate. To address this, a nitriding method called "direct-current plasma nitriding with screen (S-DCPN)" has been developed. It involves applying a voltage to the sample and screen during ASPN to remove deposits via sputtering action, thereby increasing the nitriding rate. Although the duplex process of ASPN and DLC-coating deposition has been studied, there are limited reports on the duplex process with S-DCPN. This study investigates the effect of intermediate layer composition on mechanical properties by forming a nitrided layer on the surface of SUS304 through S-DCPN treatment, depositing a Si-DLC intermediate layer with varying compositions, and applying a DLC film on the top surface. The results demonstrate that the lower the Si ratio in the Si-DLC intermediate layer, the better the wear resistance. Furthermore, the study reveals that wear resistance and adhesion were improved compared to samples without S-DCPN treatment.

Surface modification involves the chemical or physical impartation of enhanced functionality to the surface of materials, and has become increasingly important in recent years. Nitriding is a surface modification method that hardens the surface of metallic materials by causing nitrogen to permeate and diffuse into the surface to form various nitrides or by supersaturating a solid solution of nitrogen in the metal. This is effective in improving the hardness, corrosion resistance, and wear resistance. Plasma nitriding, a type of nitriding process, has several advantages, such as low energy consumption, short processing time, and low environmental impact. In contrast, the conventional plasma nitriding method forms plasma on the surface of the treated material, which may cause phenomena that lead to defects in the treated material. Therefore, the directcurrent plasma nitriding with screen (S-DCPN) method reduces these problems because plasma is formed not only on the treated material but also on the surface of the screen. Stainless steel has excellent corrosion resistance; however, nitriding treatment above a certain temperature reduces the corrosion resistance owing to chromium nitride precipitation. In this study, the S-DCPN treatment, a type of plasma nitriding method, was applied to form a thick nitrided layer without reducing corrosion resistance. The S-DCPN treatment was performed using ferritic stainless steel SUS430 as the sample and austenitic stainless steel SUS304 as the screen material at treatment temperatures of 633 and 653 K, treatment times of 5 and 15 h, a gas pressure of 200 Pa, and a gas composition of 75% N 2 - 25% H 2 . Consequently, the α N phase with supersaturated nitrogen solid solution was identified under all conditions. Nitrogen diffusion and hardness increased with increasing treatment temperature and time. In the corrosion tests, corrosion resistance improved under all conditions.

An intensive quenching (IQ) process is an environmentally friendly method of hardening steel parts. Digitally controlled, IQ employs highly agitated and directed water flow as the quenchant. An extremely high cooling rate applied uniformly over the entire part surface area induces high surface compressive stresses which prevents part distortion and cracking while forming a very fine microstructure. The fine microstructure results in better mechanical properties compared to properties imparted by conventional oil or polymer quenching. The improved mechanical properties enable engineers to design stronger steel parts for higher power density mechanical systems often using steels containing a less amount of alloying elements or using less expensive plain carbon steels. A broad and deep body of knowledge documents IQ’s ability to tailor a steel component’s microstructure to improve steel parts mechanical properties and performance. A sampling of data will be presented including surface and core hardness, tensile, yield and impact strength, elongation and reduction in area, residual surface compressive stresses for through hardened steels and the carburized grades. IQ systems can be readily “dropped in” to existing steel processing facilities or integrated into next generation heating and cooling systems through teamed relationships with equipment makers and part manufacturers seeking a sustainable future.

Heat treatment of steels is a process of modifying the mechanical properties by solid-state phase transformations or microstructural changes through heating and cooling. The material volume changes with phase transformations, which is one of the main sources of distortion. The thermal stress also contributes to the distortion, and its effect increases with solidstate phase transformations, as the material stays in the plastic deformation field due to the TRIP effect. With the basic understanding described above, the sources of distortion from a quench hardening process can be categorized as: 1) nonuniform austenitizing transformation during heating, 2) nonuniform austenite decomposing transformations to ferrite, pearlite, bainite or martensite during quenching, 3) adding of carbon or nitrogen to the material, and forming carbides or nitrides during carburizing or nitriding, 4) coarsening of carbide in tempered martensite during tempering, 5) stress relaxation from the initial state, 6) thermal stress caused by temperature gradient, and 7) nonhomogeneous material conditions, etc. With the help of computer modeling, the causes of distortion by these sources are analyzed and quantified independently. In this article, a series of modeling case studies are used to simulate the specific heat treatment process steps. Solutions for controlling and reducing distortion are proposed and validated from the modeling aspect. A thinwalled part with various wall section thickness is used to demonstrate the effectiveness of stepped heating on distortion caused by austenitizing. A patented gas quenching process is used to demonstrate the controlling of distortion with martensitic transformation for high temperature tempering steels. The effect of adding carbon to austenite on size change during carburizing is quantified by modeling, and the distortion can be compensated by adjusting the heat treat part size.

The purpose of this study is to clarify the mechanical properties of the expanded austenite (S phase) formed in austenitic stainless steel (ASS). A small thin rolled plate of SUS304 with 0.5 mm thickness was used as test sample. The test sample was nitrided by active screen plasma nitriding (ASPN) at low processing temperature of 400 °C and 450 °C during 4 h processing time. S phase was formed on the surface of the test sample. The surface hardness of ASPN sample was higher than that of untreated sample. Furthermore, tensile tests and fracture surface observations revealed that the tensile strength was also improved compared to untreated samples.

Much more steel must be produced from scrap to meet emissions targets, and utilizing this growing resource is a sound economic strategy. However, the presence of contaminating elements restricts the applications in which end-of-life scrap can replace primary steel. The use of low alloyed quenching and tempering steel grade such as 39MnCrB6-2 to reach high mechanical characteristics (around 1000 MPa) obliges often to apply low tempering temperatures for which tempering embrittlement may be observed. In this paper, it is proposed to reduce the hold time and to increase the temperature during conventional tempering to (1) reduce the embrittlement because of segregation of elements like copper, (2) to change the fracture mechanism with finer martensite sub-grains and (3) to promote θ particles with smaller dimensions but higher density.

Mold repair is a viable strategy for saving energy and reducing CO 2 emissions. Papers in the literature show that repairing a limited damaged area of the mold instead of producing a new one is becoming increasingly attractive, especially considering the latest European and international regulations introduced with the green deal. In this paper, the authors are pleased to present some preliminary results related to the repair of AISI H13 tool steel molds by Laser-Directed Energy Deposition. Steel blocks (20 x 55 x 100 mm3), previously tempered at 435±10 HV, were machined to reproduce the material removal of the damaged part of the mold. Subsequently, the region was repaired by L-DED using commercial H13 powder. The process parameters were optimized to obtain a defect-free welded area. Since the microstructure of the deposited tool steel consists of hard (730±10 HV) and brittle (7 J Charpy impact toughness) martensite, a series of post-process heat treatments were performed at different temperatures to restore a hardness compatible with that of the base steel. However, this goal was only partially achieved due to the different tempering behavior of L-DED-deposited and bulk H13 steel. In particular, the tempering temperature had to be limited to avoid softening of the base steel. In the best case, double tempering at 620 °C resulted in a toughness recovery of up to 42 J. Thermal fatigue tests showed better resistance to crack propagation after tempering, as evidenced by the shallower penetration depth compared to the as-built material.

Ductility dip cracking (DDC) is a detrimental solid-state cracking phenomenon that can occur during welding of copper-nickel (Cu-Ni) alloys used in naval vessels. The presence of these cracks has several deleterious effects, including reduced fatigue life and increased susceptibility to corrosion. The mechanism of DDC remains highly debated and understudied, especially in material systems outside of Ni-Cr-Fe alloys. The predominant mechanisms that have been proposed include: 1. Grain boundary sliding, 2. Precipitate-induced strain, and 3. Impurity element segregation. In the present body of research, thermal-mechanical testing over a wide range of strain rates and temperatures was performed using a Gleeble 3500. Both flow-stress and fracture morphology of wrought 70/30 Cu- Ni are considered. Following fracture, microstructural analyses using both scanning electron microscopy and optical microscopy were conducted to observe and quantify intergranular cracking and fracture surface features. Results show a strong correlation among fracture morphology, ductility, and temperature.

Nickel-based Inconel 625 is widely used for both low and high-temperature applications. It has several applications in aerospace, marine, chemical, and petrochemical industries due to its high strength, corrosion resistance, good formability, and weldability. With the molten pool’s rapid solidification during laser powder bed fusion (LPBF), the resulting microstructures differ from those expected in equilibrium conditions. Residual stresses, microsegregation, anisotropy, undesirable phases, layered structure, and lower mechanical properties are the challenges that must be addressed before LPBF-ed Inconel 625 parts can be industrially implemented. Heat treatment of Inconel 625 after the LPBF process is widely discussed in the literature, and the proposed heat treatment processes do not address all the challenges mentioned above. For this reason, specific heat treatments should be designed to achieve desired mechanical properties. Five different high-temperature heat treatment procedures were developed and tested in recent work in comparison with the standard heat treatment for wrought alloy (AMS 5599), to study the effect of various heat treatment parameters on the type of precipitates, grain size, room, and elevated temperature mechanical properties, and to develop an elevated-temperature tensile curve between room temperature (RT) and 760°C of LPBF-ed Inconel 625. Four heat treatment procedures showed complete recrystallization and the formation of equiaxed grain size containing annealed twins and carbide precipitates. However, either eliminating the stress relief cycle or conducting it at a lower temperature resulted in microstructures having the same pool deposition morphology with grains containing dendritic microstructure and epitaxial grains. Two different grain sizes could be obtained, starting with the same as-built microstructure by controlling post-process heat treatment parameters. The first type, coarse grain size (ASTM grain size No. G 4.5), suitable for creep application, was achieved by applying hot isostatic pressing (HIP) followed by solution annealing. The second type, fine-grain size (ASTM grain size No. G 6), preferable for fatigue properties, was achieved by applying solution annealing followed by HIP. The mechanical properties at room and elevated temperature 540°C are higher than the available properties in the AMS 5599 for wrought Inconel 625 while maintaining a higher ductility above the average level found in the standards. It can be concluded that the performed heat treatment achieves higher mechanical properties. The values of ultimate tensile strength (UTS), yield strength (YS), elongation, and reduction of area percentages are similar in the XZ and XY orientations, revealing the presence of isotropic microstructure. The ultimate tensile strength values show an anomalous behavior as a function of the temperature. From the room temperature until around 500°C, there occurs a decrease in the yield strength and a slight increase up to 600°C, decreasing sharply at 700°C. An anomaly is also present in relation to the elongation, with a significant decrease in the elongation at temperatures after 600°C.

Carbide free bainitic microstructures can be developed via different thermal processing routes, and the details affect the scale and morphology of the microstructural constituents. In this study, bainitic microstructures are formed by either a controlled cooling process or an austempering process to evaluate the relationship between microstructure and mechanical properties in a 0.2C - 2Mn - 1.5Si - 0.8Cr steel containing small amounts of Nb, Ti, B, and N, and the results are compared to a 4140 steel processed via quenching and tempering. The resulting microstructures are characterized with scanning electron microscopy. When compared to microstructures produced via austempering, microstructures produced with a controlled cool exhibit an increased variety of transformation products, specifically regarding size and distribution of martensite-austenite constituents within a lath-like bainitic ferrite matrix. Nanoindentation testing shows that different transformation products exhibit significantly different local hardness. In all (primarily) bainitic conditions tested for these materials, the martensite/austenite constituent exhibits the highest hardness, followed by the lath bainitic ferrite/retained austenite constituent. Granular bainite and coarse bainitic constituents exhibit the lowest relative hardness in the conditions where they are observed.

The analysis of cooling curves obtained by immersing a probe in the quench medium has been widely used since its availability. For instance, methods described in standards such as ISO 9950 and ASTM D 6482 refer to the use of an Inconel 600 specimen which is quenched to obtain the cooling curve of a given fluid; however, spray quenching is being mostly used in induction hardening processes. In this work, the quenching characteristics of a PAG polymer at 6 and 12 % concentration were determined and compared with water as a baseline. The fluid was heated at 30 °C, while the solution flow rate was set at 90 L/min; two different quenching rings were designed and used in a laboratory-scale setting. Also, the fluid flow in the quench rings was simulated through Computational Fluid Dynamics (CFD), to obtain flow patterns inside the quenching devices. From the results obtained, the cooling rate curves showed no vapor phase, and the maximum cooling rate was found to be higher in one of the quench ring designs. The design of the quench ring device has a significant influence on the quenching characteristics of the quenchant, mainly at medium and low temperatures of the cooling rate curve.

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. The end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream quenched large diameter continuously cast products. Therefore, in this work, coupled thermal, mechanical, and metallurgical models were used to simulate the end-quench Jominy test and in-stream quenched industrial round billets with a goal to obtain similarity of experimental structure and properties for both quenched products. For this purpose, finite element analysis (FEA) was employed using the software FORGE (by Transvalor). Used thermophysical properties were generated by JMATPro software. The evolution of microstructure during quenching and resulting hardness were simulated for AISI 4130, and AISI 4140 steel grades. The cooling rates at different positions in the Jominy bar were determined by simulation and compared to experimental. After verification and validation, the FEA simulation was utilized to predict different phases and hardness at different conditions in industry produced round billets. Additionally, relations between Jominy positions and radial positions in the billet were established allowing us to predict structure and properties in inline quenched continuously cast bar having different diameters.

Copper is expected to be increasingly used in electric vehicle components because of its high electrical and thermal conductivity. On the other hand, copper has the disadvantage of low fatigue strength compared to structural members such as steel and aluminum alloys. Therefore, the peening treatment is used in this study to increase the strength of copper. However, the projectile used in conventional peening treatments is much harder than copper, which may lead to deterioration of surface properties. Therefore, we decided to use a resin particle peening treatment that uses soft resin particles. For the projectile material, we used particles made from crushed walnut, apricot, and peach, which are natural material particles. Ceramic particles were used for comparison. Hardness measurements revealed that the near-surface hardness increased even when resin particles were used. In addition, compressive residual stresses were observed on the surface. Fatigue tests revealed that the fatigue strength improvement effect was higher than that of nontreated materials or hard particles. These results indicate that the resin particle peening treatment is an effective method for strengthening copper.