Although many have had success using CFD and FEA techniques to predict residual stress and distortion in water quenched aluminum alloys, there are still hurdles in using a computational approach to manage liquid quenching processes due to the lack of a quench severity database. Quench severity is defined by the Grossman number, which does not serve as a heat transfer model for CFD simulation because it omits much of the underlying physics. In this research, a new interpretation of quench severity makes it possible to separate the heat transfer model into two groups, one computable by CFD and one requiring calibration. The objective of this paper is to parameterize the boiling model by quenching conditions and validate the model using data obtained by quenchometer testing.

In industrial applications, hot forging of aluminum alloy AA 6082 is carried out at 480 °C following a preheating process in an induction heater. The forged parts are then cooled down to room temperature, heated up again to apply conventional solution treatment followed by quenching and artificial aging processes. Repetitive heating/cooling steps are a significant cause of energy loss. The aim of this study was to provide time and energy efficiency by combining hot forging and solution treatment processes in a single high temperature process. To achieve this a new and improved heat treatment pattern was introduced. AA6082 parts were quenched immediately from a rather high forging temperature and artificially aged without any necessity for a second heating step and solution treatment. Mechanical properties of parts heat treated by this new pattern were than compared to the mechanical properties of parts heat treated conventionally. Heat treatment of AA6082 alloys were carried out for 30 minutes at three different temperatures (480, 510 and 540 °C) for comparison, followed by forging, water quenching and artificial aging (180°C, 8h). Mechanical properties of each sample were investigated using hardness and tensile tests. Elemental analysis and microstructural characterization were carried out using Energy Dispersive Spectrometry (EDS), Scanning Electron Microscope (SEM) and Optical Microscope (OM). Required minimum hardness for the samples after heat treatment was considered as 90 HB. This hardness value could not be obtained for the parts forged/solution treated at 480°C and 510°C. Hardness values of parts heat treated at 540°C, water quenched and aged at 180°C were higher than 90 HB.

Gas quenching is drawing increasing attention within the heat treat industry. The heat transfer coefficient (HTC) for gas quenching can reach 2000 when using high pressure and high velocity nitrogen, helium, or mixtures of these gases. The HTC in water quenching is between 3000 and 4000. The lower HTC of gas quenching may result in workpieces with less distortion and residual stress after quenching. Compared to water, polymer, and oil quenching, gas quenching is environmentally friendly, and the surface of the part is clean after quenching.

Developing heat treat systems and control plans that produce consistent direct harden (quench and temper) results with a high percent martensite and the corresponding proper mechanical properties is challenging for large components or large batch sizes. In this study, large section bars in alloys suitable for water quenching were austenitized and quenched under controlled flow conditions. The bars were primarily examined by several as-quenched hardness versus depth traverses in order to be sure localized non-martensitic regions (soft areas) would be detected. The tests allowed for some key insights into defining the adequacy of direct harden water quench systems, including the idea of agitation thresholds required for each alloy grade or hardenability level to prevent soft spots (spotty hardening) on large section steel components.

Quench probes have been used effectively to characterize the quality of quenchants for many years. For this purpose a variety of commercial probes, as well as the necessary data acquisition system for determining the time- temperature data for a set of standardized test conditions, are available for purchase. The type of information obtained from such probes provides a good basis for comparing media, characterizing general cooling capabilities, and checking media condition over time. However, these data do not adequately characterize the actual production quenching process in terms of heat transfer behavior in many cases, especially when high temperature gradients are present. Faced with the need to characterize water quenching practices, including conventional and intensive practices, a quench probe was developed. This paper describes that probe, the data collection system, the data gathered for both intensive quenching and conventional water quenching, and the heat transfer coefficients determined for these processes. Process sensitivities are investigated and highlight some intricacies of quenching.