AISI 52100 is a high carbon alloy steel typically used in bearings. One hardening heat treatment method for AISI 52100 is austempering, in which the steel is heated to above austenitizing temperature, cooled to just above martensite starting (Ms) temperature in quench media (typically molten salt), held at that temperature until the transformation to bainite is completed and then cooled further to room temperature. Different austempering temperatures and holding times will develop different bainite percentages in the steel and result in different mechanical properties. In the present work, the bainitic transformation kinetics of AISI 52100 were investigated through experiments and simulation. Molten salt austempering trials of AISI 52100 were conducted at selected austempering temperatures and holding times. The austempered samples were characterized and the bainitic transformation kinetics were analyzed by Avrami equations using measured hardness data. The CHTE quench probe was used to measure the cooling curves in the molten salt from austenitizing temperature to the selected austempering temperatures. The heat transfer coefficient (HTC) was calculated with the measured cooling rates and used to calculate the bainitic transformation kinetics via DANTE software. The experimental results were compared with the calculated results and they had good agreement.

Retained austenite may be helpful or detrimental to the life of heat-treated components, but it can be difficult to accurately measure in manufactured steels. Commonly used visual sample investigations are subjective and often incorrect, magnetic measurements require part-specific calibration, and electron backscattering involves expensive equipment, intensive sample preparation, and long measurement times. Recent developments in X-ray diffractometry, however, provide measurements in minutes and can compensate for the influence of carbides in high-carbon steels as well as texture orientations in rolled sheet metals. This paper discusses the use of X-ray diffraction for measuring retained austenite and compares and contrasts it with other methods. It also provides a brief review of the formation of austenite and its effect on carburized gears, TRIP steels, and bearings.

During forging operations, strain can occur through three primary mechanisms: strain due to load applied through dies, strain due to thermal contraction, and strain due to creep. In materials behavior models, strain due to applied load and thermal contraction are directly considered and predictions are based on thermophysical properties and flow stress behaviors as inputs to the models. Strain due to creep after forging (during cooling) is often more difficult to predict and capture due to lack of materials data. In particular, data that capture the changing flow stress behavior during cooling (rather than from isothermal testing) are not commonly available. In this project, creep strain behavior during cooling was investigated by physical simulations using a Gleeble 3500. Standard cylinder-shaped Ti-6Al-4V samples with 10 mm diameter were heated to below β-transus temperature (1775°F) or above β-transus (1925°F), followed by constant cooling rates of 250°F/min and 1000°F/min with and without applied load during cooling to 1000°F. Total strain for the tests ranged from 2 – 6%. Characterization of prior microstructure and texture was carried out using XRD, optical microscopy, and SEM. The results provide insights on the relationship of flow stress behavior and microstructure as a function of temperature and cooling rate and are applicable to forging practices. These materials data can be used as input for future process modeling, potentially giving better prediction accuracy in industry applications.

Precision cold-forging processes are used to produce near-netshape parts that may then be carburized. During carburization thermal cycles, abnormal grain growth (AGG) after cold forging is known to develop microstructures which limit fatigue strength. In the present study, a small 0.04 wt.% Nb addition was made to a low-alloyed AISI 4121 steel containing 0.3 wt.% Mo. Subcritically annealed specimens were cold rolled (to simulate cold forging) at selected reduction ratios up to 50%, heated according to a simulated gas carburizing cycle at 930 °C, and water quenched to produce a final martensitic microstructure. The number density of abnormally grown grains increased rapidly as the cold rolling reduction ratio increased from 0 to 10%. With a further increase in reduction ratio, the extent of AGG decreased and was absent in samples subjected to the maximum reduction ratio of 50%. The evolution of fine (Nb, Mo)(C,N) precipitates at various stages of processing was characterized by thermodynamic calculations and electron microscopy and compared to the occurrence of abnormal austenite grain growth. The significance of these results for controlling AGG and thus optimizing fatigue performance in commercially-produced cold-forged and carburized components is discussed.