1-12 of 12 Search Results for

vertical broaching

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001231
EISBN: 978-1-62708-170-2
... Abstract This article focuses on precision and ultraprecision finish machining techniques that make use of defined cutting edges, such as polycrystalline diamond and cubic boron nitride compacts. The techniques are finish turning, finish broaching, finish milling, and finish drilling...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003189
EISBN: 978-1-62708-199-3
... chemically active oil than vertical surface broaching under comparable conditions. The heavier oil clings to the horizontal broach better than a water-miscible fluid, and chemical activity aids in efficient cutting. For vertical surface broaching of mild steels, emulsions or solutions can be used, but the...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0003991
EISBN: 978-1-62708-185-6
... outside corners of the forging to aid in material flow to define features Shape of the forging should be such that, when placed in the die, the lateral forces will be balanced. Shapes that are symmetrical along a vertical plane, such as connecting rods and shapes that are axisymmetric (or nearly so...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003214
EISBN: 978-1-62708-199-3
... Fig. 4 ) is a vertical cylinder with side walls that are stationary. The top of the cylinder is open. The bottom of the cylinder is formed by a disk that is driven to rotate at a high speed. Medium, compound, and parts are contained in the cylinder. As the disk rotates with peripheral speeds of up to...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001233
EISBN: 978-1-62708-170-2
... Simple cavities 2.2 0.085 19 × 10 3 mm 2 (30 in. 2 ) faces 1.3 0.050 Broaching (angled ECM) 7.6 0.300 Accurate estimates of feed rates usually require pilot testing in the desired ECM configuration. Electrolyte conductivity also affects resistance across the gap. Increasing the...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005255
EISBN: 978-1-62708-187-0
... movable). Injection is horizontal along the parting line; a second vertical nozzle is sometimes available. Models are available with C-frame construction and with two-, three-, and four-post H-frame construction. Machines for automatic injection have the platens mounted vertically, with injection...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0003988
EISBN: 978-1-62708-185-6
... such as fracture toughness and fatigue strength. The lateral flow also imparts some mechanical anisotropy due to grain flow. The stress state during hot repress powder forging consists of a small difference between vertical and horizontal stresses, which results in very little metal movement in the...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0003983
EISBN: 978-1-62708-185-6
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.9781627081863
EISBN: 978-1-62708-186-3
Book Chapter

Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005323
EISBN: 978-1-62708-187-0
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001243
EISBN: 978-1-62708-170-2
... work should be hung as nearly vertical as possible, with the lower edge of the work tilted from the horizontal to permit runoff at a corner rather than a whole edge. When recessed areas cannot be racked to allow proper runoff, provision should be made for drain holes or perhaps tilting of the rack when...
Series: ASM Handbook
Volume: 22B
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.hb.v22b.9781627081979
EISBN: 978-1-62708-197-9