This article describes the presses that are mechanically or hydraulically powered and used for producing sheet, strip, and plate from sheet metal. It also presents the JIC standards for presses, compares the presses based on power source, details the selection criteria and provides information on the various drive systems and the auxiliary equipment. It describes the selection of die materials and lubricants for sheet metal forming and provides information on the lubrication mechanisms and selection with a list of lubricant types for forming of specific sheet materials of ferrous or nonferrous metals. The article reviews the various types of forming processes such as blanking, piercing, fine-edge blanking, press bending, press forming, forming by multiple-slide machines, deep drawing, stretch forming, spinning, rubber-pad forming, three-roll forming, contour roll forming, drop hammer forming, explosive forming, electromagnetic forming, and superplastic forming.

Low-carbon steel sheet and strip are used primarily in consumer goods. This article discusses quality descriptors and mechanical properties of low-carbon steel sheet and strip and carbon and low-alloy steel plate. Alloy steel sheet and strip are used primarily for those special applications that require the mechanical properties normally obtained by heat treatment. Steel sheet is coated in coil form before fabrication either by the steel mills or by specialists called coil coaters. Porcelain enamels are glass coatings applied primarily to products or parts made of sheet steel, cast iron, or aluminum to improve appearance and to protect the metal surface.

This article explains the applications of continuous electroplated steel. For each category of application, the type of coating needed and the key attributes of the coating are discussed. The bulk of the article describes electrodeposition technology, including plating line components and process classification.

Shot peening is a method of cold working in which compressive stresses are induced in the exposed surface layers of metallic parts by the impingement of a stream of shot, directed at the metal surface at high velocity under controlled conditions. This article focuses on the major variables, applications, and limitations of shot peening and provides information on peening action, surface coverage, and peening intensity. It discusses the equipment used for shot recycling and shot propelling as well as the types and sizes of media used for peening. The article describes the problems in shot peening of production parts. It concludes with information on the SAE standard J442 that describes the test strips, strip holder, and gage used in measuring shot peening intensity.

Low-expansion alloys are materials with dimensions that do not change appreciably with temperature. Alloys included in this category are various binary iron-nickel alloys and several ternary alloys of iron combined with nickel-chromium, nickel-cobalt, or cobalt-chromium alloying. Low-expansion alloys are used in various applications such as rods and tapes for geodetic surveying, moving parts that require control of expansion (such as pistons for some internal-combustion engines), bimetal strip, components for electronic devices etc. This article discusses the properties, composition, and applications of iron-nickel low-expansion alloys (Invar), as well as other special alloys, including iron-nickel-chromium alloys, iron-nickel-cobalt alloys, iron-cobalt-chromium alloys, and high-strength, controlled-expansion alloys. It covers the factors affecting coefficient of thermal expansion of iron-nickel alloys, including heat treatment and cold drawing. Magnetic, physical, thermal, electrical and mechanical properties of iron-nickel alloys are also covered.

Titanium metal passes through three major steps during processing from ore to finished product: reduction of titanium ore to sponge (porous form), melting of sponge and scrap to form ingot, and remelting and casting into finished shape. This article describes primary fabrication, including all operations that convert ingot into general mill products, such as billet, bar, plate, sheet, strip, tube, and wire. The section on secondary fabrication describes processes such as die forging, extrusion, hot and cold forming, machining, chemical milling, and joining. The article presents a short note on powder metallurgy products of titanium. Casting processes and properties are covered in the final section.

There are various coating techniques in practice to prevent the deterioration of steels. This article focuses on dip, barrier, and chemical conversion coatings and describes hot-dip processes for coating carbon steels with zinc, aluminum, lead-tin, and other alloys. It describes continuous electrodeposition for steel strip and babbitting and discusses phosphate and chromate conversion coatings as well. It also addresses painting, discussing types and selection, surface preparation, and application methods. In addition, the article describes rust-preventive compounds and their application. It also provides information on weld-overlay and thermal spray coating, porcelain enameling, and the preparation of enamel frits for steels. The article closes by describing methods and materials for ceramic coating.

This article discusses the operating principles, types, and applications of shearing and slitting of different forms of steel, including plates, flat sheets, bars, coiled sheet and strips. In addition, it provides a detailed account of the cutting methods such as oxyfuel gas cutting, plasma arc cutting, oxygen arc cutting, laser beam cutting, and air carbon arc cutting and gouging, describing their process capabilities, equipment used, operating principles and parameters, and factors affecting their efficiency.

Molten salt baths are anhydrous, fused chemical baths used at elevated temperatures for a variety of industrial cleaning applications. This article discusses their applications in paint stripping, polymer removal, casting cleaning, glass removal, and plasma/flame spray removal. It provides an overview of the basic design and safety considerations of the salt bath equipment and describes the environmental impact of molten salt bath cleaning.

This article focuses on the electrodeposition of indium and its alloys, such as indium-antimony, indium-gallium, and indium-bismuth, in nonaqueous indium plating baths. It also provides information on the stripping of indium plate from plated components and presents an overview of the specifications, standards, and hazards of indium plating.

Ferrous metals are metals that contain primarily iron and may have small amounts of other elements added to give the desired properties. This article discuses the characteristics of steel products used in most industries, including construction, automotive, energy, shipping, and agriculture. These products include bars, rods, wires, hot and cold rolled sheets, strip plates, tin mill products, steel tubes, castings, and forgings. The article also provides information on the methods used to prevent or control the rusting of ferrous materials, namely, alloying, coating, and covering.

This article discusses the methods, equipment, and theory for pouring, solidifying, and stripping steel ingots. It describes the two basic types of pouring methods: top pouring and bottom pouring. The equipment includes hot tops, ingot molds, and stools. The design of the ingot is dictated by the application and type of steel involved. The article concludes with information on the applications of solidification simulation.

This article discusses different forms of ingot and explains molten-metal processing. It describes ingot casting processes, namely, open-mold casting and direct chill (DC) process. The process variations and solidification in the DC process are summarized. The article describes continuous processes, namely, twin-roll strip casting, slab casting, and wheel-belt processes. It concludes with information on postsolidification processes, including stress relief and scalping.

This article reviews the history and methods of copper alloy continuous casting. The methods include vertical continuous casting and horizontal continuous casting. The article discusses the upcasting methods used in vertical continuous casting and strip casting used in horizontal continuous casting. The upcasting methods include Outokumpu upcasting method, Rautomead upwards vertical casting, and pressure upcasting. The article also describes the methods and processes of wheel casting and Ohno continuous casting.

This article reviews the steps involved in presurface-preparation inspection: substrate replacement; removal of weld spatter, rounding of sharp edges, and grinding of slivers/laminations; and removal of rust scale, grease, oil, and chemical (soluble salt) contamination. It focuses on surface preparation methods that range from simple solvent cleaning to hand and power tool cleaning, dry and wet abrasive blast cleaning, centrifugal wheel blast cleaning, chemical stripping, and waterjetting for the application of the coating system. In addition, the article provides a description of the Society for Protective Coatings' (SSPC) standards and NACE International standards as well as the International Organization for Standardization (ISO) standards and International Concrete Repair Institute (ICRI) guidelines for surface cleanliness.

Fracture surfaces are fragile and subject to mechanical and environmental damage that can destroy microstructural features. This article discusses the importance of care and handling of fractures and the factors that need to be considered during the preliminary visual examination. It describes the procedures for sectioning a fracture and opening secondary cracks as well as the effect of nondestructive inspection on subsequent evaluation. The article provides information on the most common techniques for cleaning fracture surfaces. These techniques are dry air blast cleaning, replica stripping, organic-solvent cleaning, water-base detergent cleaning, cathodic cleaning, and chemical-etch cleaning.

This article describes the types of steels, including high-strength structural carbon steels and high-strength low-alloy steels (HSLA), available in all standard wrought forms such as sheet, strip, plate, structural shapes, bars, bar-size shapes. It discusses the special sections that are characterized by higher yield strengths than those of plain carbon structural steels. The article tabulates the typical chemical compositions, tensile properties, heat treatment, product sizes, plate thickness and intended uses of high-strength steels. Further, it presents a short note on heat treated structural low-alloy grades.

This article focuses on the various techniques for removing contaminants in the surface preparation of steel for hot-dip coatings: wet cleaning methods, including alkaline cleaning, electrolytic cleaning, chemical pickling, and electrolytic pickling; flame cleaning and furnace-atmosphere techniques, such as Sendzimir oxidation/reduction method; other specialized methods, namely, fluxes, mechanical cleaning, and ultrasonic methods; or a combination of these.

This article explores the potential of through-process simulations of the development of microstructure, texture, and resulting properties during the thermomechanical processing of Al-Mn-Mg alloys, starting from the as-cast ingot to final-gage sheet. It provides an introduction of the thermomechanical production of aluminum sheet and, in particular, highlights the main effects governing the evolution of microstructure and texture. The simulation tools used to model the evolution of microchemistry, microstructure, and texture upon deformation and recrystallization of aluminum alloys are described. The article discusses the recrystallization behavior of alloy AA 3104 during the interstand times in between two consecutive hot rolling passes with the help of combined microstructure models.

Pickling is the most common of several processes used to remove scale from steel surfaces. This article provides a discussion on pickling solutions, such as sulfuric and hydrochloric acid, and describes the role of inhibitors in acid pickling. It discusses the equipment and processes involved in the batch, continuous, and electrolytic pickling of carbon steel components. The article describes the effects of process variables on scale removal in sulfuric and hydrochloric acid. It concludes with a description of pickling defects, spent pickle liquor disposal, and safety practices.