1-20 of 92 Search Results for

stretch draw forming

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003178
EISBN: 978-1-62708-199-3
... 1 mm (0.02 to 0.04 in.) in diameter. BARS are bent by four basic methods: draw bending, compression bending, roll bending, and stretch bending. In draw bending, the workpiece is clamped to a rotating form and drawn by the form against a pressure die ( Fig. 7 ). The pressure die can be either...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003177
EISBN: 978-1-62708-199-3
... nonferrous metals. The article reviews the various types of forming processes such as blanking, piercing, fine-edge blanking, press bending, press forming, forming by multiple-slide machines, deep drawing, stretch forming, spinning, rubber-pad forming, three-roll forming, contour roll forming, drop hammer...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003181
EISBN: 978-1-62708-199-3
....) Material that has been solution heat treated at the mill, but not artificially aged (T3, T4, or W temper), is generally suitable only for mild forming operations such as bending, mild drawing, or moderate stretch forming. Solution heat treated and artificially aged (T6 temper) alloys are seldom used...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.9781627081863
EISBN: 978-1-62708-186-3
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003180
EISBN: 978-1-62708-199-3
... required for best results in drawing, stretch forming, or spinning. In press-brake forming, lubrication is seldom needed. Sulfurized or sulfochlorinated oils may be used if the work is carefully cleaned afterward in a degreaser or an alkaline cleaner. Work that has been formed in zinc alloy dies should be...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004021
EISBN: 978-1-62708-185-6
... reduction combination cannot maintain compressive axial stresses in the drawn component, the center portion will be stretched, and the tensile stress may increase to a level where bursting occurs ( Fig. 48 ). In the first forming operation for a component, the stresses in the component may be high, but the...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004028
EISBN: 978-1-62708-185-6
... deformation is partitioned between the grains is a characteristic of the polycrystal model used, and this section surveys some of the models. At the level of the polycrystal, the macroscopic velocity gradient can be decomposed into a stretch rate and a spin rate component, as is done for the single crystal...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004014
EISBN: 978-1-62708-185-6
... evaluating the microstructure of a flow-formed Ti-6Al-4V part, the longitudinal cross section is composed of primary globular alpha grains that had become elongated or stretched parallel to the axis, surrounded by fine transformed beta grains also elongated in the direction of metal flow. In contrast...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004017
EISBN: 978-1-62708-185-6
... tests, such as the tension test, ring compression test, plane-strain compression test, bend test, indentation test, and forgeability test. It concludes with information on the role of the finite-element modeling software used in workability analysis. bend test bulk forming processes cracking...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004008
EISBN: 978-1-62708-185-6
... pulled forward by the frictional force created by the sliding movement of the deforming tube. Therefore, the plug must be held in the correct position with a plug bar. In drawing long and small-diameter tubes, the plug bar may stretch and even break. In such cases, it is advantageous to use a floating...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0009006
EISBN: 978-1-62708-185-6
... drawing and extrusion, and so the elongation has little bearing on relative workability. It is unfortunate that such wide use is made of elongation or stretching data in an effort to forecast workability. Compression testing (See the articles “Cold Upset Testing” and “Hot-Compress Testing” in this...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003018
EISBN: 978-1-62708-200-6
...-effective manufacturing method for making certain items. Thermoforming is less limited than metal stamping in stretching, depth-of-draw ratio, and material distribution. Its advantages include a reasonable capital investment, rapid cycles and resulting high productivity, the capability for handling a wide...
Book Chapter

Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004012
EISBN: 978-1-62708-185-6
... the material being worked should be relatively free of oxide and scale. Spalling or chipping may be the direct result of endwise extrusion or stretching of the blank during rolling, over-rolling, improper blank design, or inferior design or quality of tools. When spalling occurs, relatively large...
Book Chapter

Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006790
EISBN: 978-1-62708-295-2
.... In dies, common causes of galling are stretching sheet metal beyond practical limits, tool fitting with poor alignment or insufficient die clearance for the given sheet thickness, wrinkles, the use of galling-susceptible tool steel, and rough finish on the surface of tools. Correct lubrication of the...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003121
EISBN: 978-1-62708-199-3
... only for mild forming operations such as bending, mild drawing, or moderate stretch forming if these operations cannot be performed immediately after quenching. Solution heat-treated and artificially aged (T6 temper) alloys are in general unsuitable for forming operations. Aluminum alloys an be...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003065
EISBN: 978-1-62708-200-6
... Increases the melting rate by bringing hot melt under the batch blanket and removing cooler partially melted material Aids homogenization by shearing and stretching the melt The control of the flow patterns is the primary aim of the design and operation of a glass furnace. These flow patterns are...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003137
EISBN: 978-1-62708-199-3
... Abstract Copper and copper alloys are widely used in many environments and applications because of their excellent corrosion resistance, which is coupled with combinations of other desirable properties. This article lists the identifying characteristics of the forms of corrosion that commonly...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003094
EISBN: 978-1-62708-199-3
... good formability, the coating is applied over low-carbon steel sheet of commercial quality, drawing quality, or drawing quality special killed, The terne coating acts as a lubricant and facilitates forming, and the strong bond of the terne metal allows it to be formed along with the basis metal. When...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003015
EISBN: 978-1-62708-200-6
... die at about 190 °C (375 °F) and cooled to about 120 °C (250 °F) by being passed between rolls. Inside a temperature-controlled box, the moving sheet, rewarmed to 130 °C (265 °F), is grasped on either side by tenter hooks, which exert a drawing tension (longitudinal stretching) as well as a widening...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005330
EISBN: 978-1-62708-187-0
... part but to meet the surface-quality requirements. Unnecessary finishing increases cost and stretches out production times. Traditional measures of surface roughness are not normally useful in casting surface inspection, since the texture of the casting is more severe and long range than machined...