Search Results for stainless

This article is an atlas of fractographs that helps in understanding the causes and mechanisms of fracture of precipitation-hardening stainless steels and in identifying and interpreting the morphology of fracture surfaces. The fractographs illustrate the cup-and-cone tension-overload fracture, low-cycle and high-cycle fatigue fracture, fracture surface, brittle intergranular fracture, hydrogen embrittlement, and intergranular stress-corrosion cracking of stainless steel components of these steels. The components include high-pressure compressor parts, springs, deflector yokes of aircraft main landing gears, and aircraft engine mount beams.

This article is an atlas of fractographs that helps in understanding the causes and mechanisms of fracture of austenitic stainless steels and in identifying and interpreting the morphology of fracture surfaces. The fractographs illustrate the following: fatigue-crack fracture, rock candy fracture, cleavage fracture, brittle fracture, high-cycle fatigue fracture, fatigue striations, hydrogen-embrittlement failure, creep crack propagation, fatigue crack nucleation, intergranular creep fracture, torsional overload fracture, stress-corrosion cracking, and grain-boundary damage of these steels. The austenitic stainless steel components include spring wires, preheater-reactor slurry transfer lines and gas lines of coal-liquefaction pilot plants, oil feed tubes and suction couch rolls of paper machines, cortical screws and compression hip screws of orthopedic implants, and Jewett nails.

This article is an atlas of fractographs that helps in understanding the causes and mechanisms of fracture of martensitic stainless steels and in identifying and interpreting the morphology of fracture surfaces. The fractographs illustrate the fracture surface, high-cycle fatigue fracture, tensile-shear fracture, intergranular crack, fatigue striations, and microvoid coalescence of conveyor-chain links, hub socket of aircraft propellers, and automotive intake valves of these steels.

This article describes metallographic preparation and examination techniques for stainless steels and maraging steels. It presents a series of micrographs demonstrating microstructural features of these alloys. Procedures used to prepare stainless steels for macroscopic and microscopic examination are similar to those used for carbon, alloy, and tool steels. Cutting and grinding must be carefully executed to minimize deformation because the austenitic grades work harden readily. The high-hardness martensitic grades that contain substantial undissolved chromium carbide are difficult to polish while fully retaining the carbides. Unlike carbon, alloy, and tool steels, etching techniques are more difficult due to the high corrosion resistance of stainless steels and the various second phases that may be encountered. The microstructures of stainless steels can be quite complex. Matrix structures vary according to the type of steel, such as ferritic, austenitic, martensitic, precipitation hardenable, or duplex.

Stainless steels, based on forging pressure and load requirements, are more difficult to forge because of the greater strength at elevated temperatures and the limitations on the maximum temperatures at which stainless steels can be forged without incurring microstructural damage. This article discusses the forging methods, primary mill practices (primary forging and ingot breakdown), trimming, and cleaning operations of stainless steels. It describes the use of forging equipment, dies, and die material in the forging operation. The article provides an overview of the forgeability of austenitic stainless steels, martensitic stainless steels, precipitation-hardening stainless steels, and ferritic stainless steels. It concludes with a discussion on the heating and lubrication of dies.

This article describes the fracture toughness behavior of austenitic stainless steels and their welds at ambient, elevated, and cryogenic temperatures. Minimum expected toughness values are provided for use in fracture mechanics evaluations. The article explains the effect of crack orientation, strain rate, thermal aging, and neutron irradiation on base metal and weld toughness. It discusses the effect of cold-work-induced strengthening on fracture toughness. The article examines the fracture toughness behavior of aged base metal and welding-induced heat-affected zones. It concludes with a discussion on the Charpy energy correlations for aged stainless steels.

This article reviews the influence of local strains and corrosion fatigue on the initiation of fatigue cracks in duplex stainless steels. It provides useful information on fatigue crack growth, fatigue strength, and fracture toughness of duplex stainless steels. The article discusses the fatigue and fracture behavior of duplex stainless steels during stress-corrosion cracking. It details the elevated-temperature properties of duplex stainless steels, such as creep-fatigue behavior and thermal cycling properties.

This article summarizes the key mechanical characteristics of various types of stainless steel, including ferritic, austenitic, martensitic, precipitation hardening, and duplex steels. Particular emphasis is on fracture properties and corrosion fatigue. The article tabulates typical room-temperature mechanical properties and fatigue endurance limits of stainless steels. Stainless steels are susceptible to embrittlement during thermal treatment or elevated-temperature service. The article discusses embrittlement in terms of sensitization, 475 deg C embrittlement, and sigma-phase embrittlement. It also describes the effect of environment on fatigue crack growth rate.

The machinability of stainless steels varies from low to very high, depending on the final choice of the alloy. This article discusses general material and machining characteristics of stainless steel. It briefly describes the classes of stainless steel, such as ferritic, martensitic, austenitic, duplex, and precipitation-hardenable alloys. The article examines the role of additives, such as sulfur, selenium, tellurium, lead, bismuth, and certain oxides, in improving machining performance. It provides ways to minimize difficulties involved in the traditional machining of stainless steels. The article describes turning, drilling, tapping, milling, broaching, reaming, and grinding operations on stainless steel. It concludes with information on some of the nontraditional machining techniques, including abrasive jet machining, abrasive waterjet machining electrochemical machining, electron beam machining, and plasma arc machining.

This article discusses the selection of types of stainless steel for various methods of forming based on the formability and on the power required for forming. It reviews the requirements of lubrication, blanking, and piercing. The article describes various forming methods, namely, press-brake forming, press forming, multiple-slide forming, deep drawing, spinning, rubber-pad forming, drop hammer forming¸ three-roll forming, contour roll forming, stretch forming, and bending of tubing.

Materials of construction for equipment and piping in pharmaceutical processing plants must be resistant to corrosion from the high-purity water, the buffer solutions used in preparation of the products, and the cleaning solutions used to maintain the purity of the product. The primary water used in pharmaceutical production is water for injection (WFI). This article presents the steps for preparing WFI and discusses the effect of chlorides on stainless steel. It provides information on the passive layer of stainless steels and chromium-containing nickel alloys. The article provides information on the surface finish of pharmaceutical equipment. It discusses the classification of rouge and the characteristics of cast type 316L stainless steel. The article also explains how and when to perform cleaning and repassivation process on classes of rouge.

This article tabulates the chemical composition of iron-base, titanium-base, and cobalt-base alloys and illustrates the microstructures of these materials. It discusses the surface morphology and chemistry of oxide-film-covered alloys and provides insights into the interaction. The article illustrates the interfacial structure of a biomaterial surface contacting with the biological environment. It describes the corrosion behavior of stainless steel, cobalt-base alloy, and titanium alloys. The electrochemical methods used for studying metallic biomaterials corrosion are also discussed. The article concludes with information on the biological consequences of in vivo corrosion and biocompatibility.

This article reviews the properties of cast steels that are specified for liquid corrosion service at temperatures above and below 650 deg C. Stainless steel castings are usually classified based on their resistance to corrosion and heat and generally fall into one category or the other. The article describes alternate methods for classifying cast stainless steels, one is based on grade designations, the other on microstructural analysis. It also addresses heat treatment, pointing out its similarities with the thermal processing of wrought materials, and establishes the importance of mechanical properties in material selection. The article presents information on the selection process and provides a detailed list of heat-resistant cast steels and alloys. It also includes key manufacturing characteristics to aid in foundry and welding-related decisions.

Stainless steels are widely used at elevated temperatures when carbon and low-alloy steels do not provide adequate corrosion resistance and/or sufficient strength at these temperatures. This article deals with the wrought stainless steels used for high temperature applications. It gives some typical compositions of wrought heat-resistant stainless steels, which are grouped into ferritic, martensitic, austenitic, and precipitation-hardening (PH) grades. Quenched and tempered martensitic stainless steels are essentially martensitic and harden when air cooled from the austenitizing temperature. These alloys offer good combinations of mechanical properties. The article focuses on mechanical property considerations and corrosion resistance considerations of stainless steels. The corrosion and oxidation resistance of wrought stainless steels is similar to that of cast stainless steels with comparable compositions.

This article discusses the composition, characteristics, and properties of the five groups of wrought stainless steels: martensitic stainless steels, ferritic stainless steels, austenitic stainless steels, duplex stainless steels, and precipitation-hardening stainless steels. The selection of stainless steels may be based on corrosion resistance, fabrication characteristics, availability, mechanical properties in specific temperature ranges and product cost. The fabrication characteristics of stainless steels include formability, forgeability, machinability, and weldability. The product forms of wrought stainless steels are plate, sheet, strip, foil, bar, wire, semifinished products, pipes, tubes, and tubing. The article describes tensile properties, elevated-temperature properties, subzero-temperature properties, physical properties, corrosion properties, and fatigue strength of stainless steels. It characterizes the experience of a few industrial sectors according to the corrosion problems most frequently encountered and suggests appropriate grade selections. Corrosion testing, surface finishing, mill finishes, and interim surface protection of stainless steels are also discussed.

Precipitation hardening is a hardening mechanism found in various steels and alloy systems, such as nickel-, cobalt-, titanium-, copper-, and iron-base alloys. This article provides a brief description of precipitation hardening process, furnace equipment, surface-related problems, and protective atmospheres used in heat treatment of iron-base precipitation-hardenable (PH) superalloys. It focuses on various factors to be considered in heat treating of PH stainless steels: cleaning prior to heat treatment, furnace atmospheres, time-temperature cycles, variations in cycles, and scale removal after heat treatment. The article describes the mechanical properties, solution treatment, and aging treatment for many martensitic PH alloys, including: Alloy 17-4 PH, Alloy 13-8 Mo, Alloy 15-5 PH, Custom 450, and Custom 455; as well as semiaustenitic PH stainless steels such as Alloy 17-7 PH, Alloy PH 15-7 Mo, AM-350, Pyromet 350, AM-355, and Pyromet 355; austenitic PH stainless steel, A-286; cast PH stainless steels; and iron-nickel PH superalloys.

Low-temperature carburization hardens the surface of austenitic stainless steels through the diffusion of interstitial carbon without the formation of carbides. This article provides an overview on austenitic stainless steels and low-temperature carburization. It reviews the competing technologies and commercial application of low-temperature carburization. The article discusses several processing parameters, including activation of the surface, proper surface preparation, selection and condition of the alloy to be carburized, treatment temperature, and carburizing atmosphere for successful low-temperature carburization of austenitic stainless steels and other chromium-containing alloys. It describes the performance properties of the low-temperature carburized layer: fatigue resistance, wear resistance, erosion resistance, and corrosion resistance.

Ferritic stainless steels are essentially chromium containing steel alloys with at least 10.5% Cr. They can be grouped based on their chromium content: low chromium (10.5 to 12.0%), medium chromium (16 to 19%), and high chromium (greater than 25%). This article provides general information on the metallurgy of ferritic stainless steels. It describes two types of heat treatments to avoid sensitization and embrittlement. They are annealing and stress relieving. The article also provides information on casting and stabilization of ferritic stainless steels to avoid precipitation of grain boundary carbides.

This article provides information on the metallurgy of austenitic stainless steels, and the formation of their intermediate phases (Sigma, Chi, and Laves). It discusses sensitization, a major problem associated with the austenitics, and solutions to avoid the problem. The article describes heat treatments applied to austenitic stainless steels, namely, soaking for homogenization and preparation for hot working; annealing to remove the effects of cold work and to put alloying elements into solid solution; and stress relieving. It provides information on the stabilizing anneal process, which is conducted on stabilized alloys, and discusses the metallurgical characteristics of austenitic stainless steels that may affect the selection of a stress-relieving treatment and prevention of stress corrosion by stress relieving. The article also discusses the heat treatments applied to duplex stainless steels, which involve soaking and annealing, achieving the austenite-ferrite balance, precipitation of intermetallics, and alpha prime precipitation.

Low-temperature surface hardening is mostly applied to austenitic stainless steels when a combination of excellent corrosion performance and wear performance is required. This article provides a brief history of low-temperature surface hardening of stainless steel, followed by a discussion on physical metallurgy, including crystallographic identity, thermal stability and decomposition, nitrogen and carbon solubility in expanded austenite, and diffusion kinetics of interstitials. It provides a description of low-temperature nitriding and nitrocarburizing processes for primarily austenitic and, to a lesser extent, other types of stainless steels along with practical examples and industrial applications of these steels.