1-15 of 15 Search Results for

spallation fixtures

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003303
EISBN: 978-1-62708-176-4
..., spallation fixtures, and the flyer-plate experiment, are also discussed. References References 1. Rankine W.J.M. , On the Thermodynamic Theory of Waves of Finite Longitudinal Disturbance , Philos. Trans. R. Soc. (London) , Vol 160 , 1870 , p 277 – 288 10.1098/rstl.1870.0015 2...
Series: ASM Handbook
Volume: 5A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v05a.a0005730
EISBN: 978-1-62708-171-9
... through the introduction of a hole Fig. 1 Schematic of the square-based diamond pyramid indenter used for the Vickers hardness test, and an example of the indentation it produces Fig. 2 Coating/fixture assembly used for tensile adhesion testing of thermal spray coatings. Dimensions...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001299
EISBN: 978-1-62708-170-2
... , Therm. Conduct. , Vol 20 , Hasselman D.P.H. and Thomas J.R. Jr. , Ed., Plenum Publishing Corp. , 1989 , p 93 – 101 The TBC system is expected to survive the thermal shock of rapid cycle heating and cooling, as experienced in gas turbine or diesel engines, without spallation...
Series: ASM Handbook
Volume: 5A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v05a.a0005716
EISBN: 978-1-62708-171-9
... the substrate material and is positioned (attached to the part or coating fixture) in such a way as to closely replicate the coating being applied to the part. Figure 12 shows the basic postcoating inspections. Fig. 12 Postcoating inspection Nondestructive Testing Destructive Testing...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003304
EISBN: 978-1-62708-176-4
...-Induced Phase Transition and Mechanisms of Spallation in Shock Loaded Titanium Alloys , 11th APS Topical Group Meeting on Shock Condensed Matter , Snowbird, UT , 1999 90. Vohra Y.K. , Sikka S.K. , Vaidya S.N. , and Chidambaram R. , Impurity Effects and ReactionKinetics...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0003817
EISBN: 978-1-62708-183-2
... liquid metal embrittlement in the heat-affected zone ( Ref 15 , 16 ). Care must be taken, therefore, to avoid copper contamination of the area to be welded, either from copper jigs and fixtures or from the use of copper wire cleaning brushes. Stainless steel wire brushes are recommended for interpass...
Series: ASM Handbook
Volume: 13A
Publisher: ASM International
Published: 01 January 2003
DOI: 10.31399/asm.hb.v13a.a0003671
EISBN: 978-1-62708-182-5
... repeated scale formation and spallation cycles or through selective internal compound formation. Catastrophic corrosion occurs when a liquid phase is a product of a corrosion process. This may happen as a result of metal or alloy exposure to vapors of a low-melting compound or during the substrate...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0003821
EISBN: 978-1-62708-183-2
...). This alloy was developed in 1905 and is still used in a wide variety of applications, such as seawater, non-oxidizing acids, hydrocarbon processing, water-fed heat exchangers, neutral and alkaline salts and alkali process equipment, industrial plumbing and valves, marine fixtures, petrochemical equipment...
Series: ASM Handbook
Volume: 20
Publisher: ASM International
Published: 01 January 1997
DOI: 10.31399/asm.hb.v20.a0002493
EISBN: 978-1-62708-194-8
... on the outer surface of a component subjected to fatigue loads, tensile stresses on the inner surface of an austenitic stainless steel pipe caused by welding leading to intergranular stress-corrosion cracking in boiling water reactors, interlaminar stresses in coatings leading to their spallation, premature...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003217
EISBN: 978-1-62708-199-3
Series: ASM Handbook
Volume: 20
Publisher: ASM International
Published: 01 January 1997
DOI: 10.31399/asm.hb.v20.a0002466
EISBN: 978-1-62708-194-8
... a metallurgical bond that is not susceptible to spallation and can easily be applied free of porosity or other defects. Welded deposits of surface alloys can be applied in thicknesses greater than most other techniques, typically in the range of 3 to 10 mm. Most welding processes are used for application...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003217
EISBN: 978-1-62708-199-3
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.9781627081993
EISBN: 978-1-62708-199-3
Series: ASM Handbook Archive
Volume: 10
Publisher: ASM International
Published: 01 January 1986
DOI: 10.31399/asm.hb.v10.9781627081788
EISBN: 978-1-62708-178-8
Series: ASM Handbook
Volume: 2
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v02.9781627081627
EISBN: 978-1-62708-162-7