1-12 of 12 Search Results for

single-rib wheel traverse grinding

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book Chapter

Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002141
EISBN: 978-1-62708-188-7
... describes the five basic methods employed for cylindrical thread grinding, namely, single-rib wheel traverse grinding, multirib wheel traverse grinding, multirib wheel plunge grinding, multirib wheel skip-rib, or alternate-rib, grinding, and multirib wheel three-rib grinding. It also provides an overview...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002145
EISBN: 978-1-62708-188-7
... in sliding on tooth flanks. These gears have low load-carrying capacity, but are useful where shafts must rotate at an angle to each other. Fig. 6 Mating crossed-axes helical gears Worm gear sets are usually right-angle drives consisting of a worm gear (or worm wheel) and a worm. A single...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006493
EISBN: 978-1-62708-207-5
... cooling of the workpiece and facilitates flow of metal into small cavities in the die. However, there are limitations to the geometric complexity that can be obtained. Guidelines are discussed regarding the effects of parting line on the grain flow, taper (draft) angles, fillet and corner radii, rib...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001810
EISBN: 978-1-62708-180-1
... by natural diamond dust (≤5 μm) that was deliberately introduced into the lubricant in the laboratory. Deep grooving of the raceways and excessive wear of the rib and roller ends is evident. Similar wear can occur from hard third particles, such as bearing or gear materials, sand, or machining chips. Source...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002395
EISBN: 978-1-62708-193-1
.... In other instances, more extensive changes are required, such as significantly increasing the cross-sectional area or adding a strengthening rib. Corrosion effects can be lessened by alloying, by providing galvanic protection, or by altering or removing a corrosive environment. Galvanic protection...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.9781627082006
EISBN: 978-1-62708-200-6
Series: ASM Handbook
Volume: 4A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v04a.a0005807
EISBN: 978-1-62708-165-8
...(a) , consists of locally heating selected areas with a suitable flame head and subsequently quenching. Both the component and the flame are held stationary. The heating head may be of either single-orifice or multiple-orifice design, depending on the extent of the area to be hardened. The heat input must...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.9781627081993
EISBN: 978-1-62708-199-3
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002147
EISBN: 978-1-62708-188-7
... Abstract This article provides information on the operating principle, tool material and design changes, and safety and protection of various multifunction machines as well as the cutting fluids used. These include single-spindle automatic lathes, manual turret lathes, single-spindle automatic...
Series: ASM Handbook
Volume: 17
Publisher: ASM International
Published: 01 August 2018
DOI: 10.31399/asm.hb.v17.a0006468
EISBN: 978-1-62708-190-0
... of direct current is the rectification of alternating current. Both the single-phase ( Fig. 5a ) and three-phase types of alternating current ( Fig. 5b ) are furnished commercially. By using rectifiers, the reversing alternating current can be converted into unidirectional current, and when three-phase...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.9781627081955
EISBN: 978-1-62708-195-5
Series: ASM Handbook
Volume: 4A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v04a.9781627081658
EISBN: 978-1-62708-165-8