This article describes the presses that are mechanically or hydraulically powered and used for producing sheet, strip, and plate from sheet metal. It also presents the JIC standards for presses, compares the presses based on power source, details the selection criteria and provides information on the various drive systems and the auxiliary equipment. It describes the selection of die materials and lubricants for sheet metal forming and provides information on the lubrication mechanisms and selection with a list of lubricant types for forming of specific sheet materials of ferrous or nonferrous metals. The article reviews the various types of forming processes such as blanking, piercing, fine-edge blanking, press bending, press forming, forming by multiple-slide machines, deep drawing, stretch forming, spinning, rubber-pad forming, three-roll forming, contour roll forming, drop hammer forming, explosive forming, electromagnetic forming, and superplastic forming.

Low-carbon steel sheet and strip are used primarily in consumer goods. This article discusses quality descriptors and mechanical properties of low-carbon steel sheet and strip and carbon and low-alloy steel plate. Alloy steel sheet and strip are used primarily for those special applications that require the mechanical properties normally obtained by heat treatment. Steel sheet is coated in coil form before fabrication either by the steel mills or by specialists called coil coaters. Porcelain enamels are glass coatings applied primarily to products or parts made of sheet steel, cast iron, or aluminum to improve appearance and to protect the metal surface.

This article explores the potential of through-process simulations of the development of microstructure, texture, and resulting properties during the thermomechanical processing of Al-Mn-Mg alloys, starting from the as-cast ingot to final-gage sheet. It provides an introduction of the thermomechanical production of aluminum sheet and, in particular, highlights the main effects governing the evolution of microstructure and texture. The simulation tools used to model the evolution of microchemistry, microstructure, and texture upon deformation and recrystallization of aluminum alloys are described. The article discusses the recrystallization behavior of alloy AA 3104 during the interstand times in between two consecutive hot rolling passes with the help of combined microstructure models.

Sheet molding compound (SMC) is a composite material - consisting of glass-fiber-reinforced polyester in a resin matrix - that’s available in sheet form for the production of compression-molded parts. This article discusses the components incorporated into the resin paste, including catalysts, fillers, thickeners, pigments, thermoplastic polymers, flame retardants, and ultraviolet absorbers, and how to optimize them to achieve the desired processing and molding characteristics and the necessary properties in the resulting parts. The article also presents several mixing techniques, including batch, batch/continuous, and continuous mixing, and describes the operations of continuous-belt and beltless machine type SMCs.

The compression molding process is most commonly called the sheet molding compound (SMC) process in reference to the precursor sheet molding compound material it uses. This article discusses the types of materials used for sheet manufacture, and describes the manufacturing and processing parameters of SMC components, providing details on tooling and process advantages and limitations. The article provides a general overview of the types of compression molding processes, including structural compression molding and thermoplastic compression molding.

Thermoforming is a manufacturing process in which thermoplastic sheets are heated, softened, clamped onto a mold, and made to conform to the shape of the mold or forming tool. It is ideally suited to large-volume runs of small items. This article focuses on major phases of thermoforming, namely, sheet transportation, heating, forming/cooling, and trimming, and different thermoforming techniques: basic female forming; basic male forming; matched-mold thermoforming; plug-assist thermoforming; pressure bubble plug-assist vacuum thermoforming; vacuum snapback thermoforming; air-slip thermoforming; and trapped-sheet, contact heat, and pressure thermoforming. It concludes with a discussion on machines and the economic concerns of thermoforming.

This article contains nine tables that present useful formulas for deformation analysis and workability testing. The tables present formulas for effective stress, strain, and strain rate in arbitrary coordinates, principal, compression and tension testing of isotropic material. The article also provides formulas for flat rolling, conical-die extrusion, wire drawing, deep drawing of cups from sheet metal, and bending, and formulas for anisotropic sheet materials.

This article discusses the operating principles, types, and applications of shearing and slitting of different forms of steel, including plates, flat sheets, bars, coiled sheet and strips. In addition, it provides a detailed account of the cutting methods such as oxyfuel gas cutting, plasma arc cutting, oxygen arc cutting, laser beam cutting, and air carbon arc cutting and gouging, describing their process capabilities, equipment used, operating principles and parameters, and factors affecting their efficiency.

This article outlines several polycrystal formulations commonly applied for the simulation of plastic deformation and the prediction of deformation texture. It discusses the crystals of cubic and hexagonal symmetry that constitute the majority of the metallic aggregates used in technological applications. The article defines the basic kinematic tensors, reports their relations, and presents expressions for calculating the change in crystallographic orientation associated with plastic deformation. It surveys some of the polycrystal models in terms of the relative strength of the homogeneous effective medium (HEM). The article analyzes the anisotropy predictions of rolled face-centered-cubic and body centered-cubic sheets and presents simulations of the axial deformation of hexagonal-close-packed zirconium. The applications of polycrystal constitutive models to the simulation of complex forming operations, through the use of the finite element method, are also presented.

The primary objectives of the rolling process are to reduce the cross section of the incoming material while improving its properties and to obtain the desired section at the exit from the rolls. This article illustrates a rolling sequence for the fabrication of bars, shapes, and flat products from blooms, billets, and slabs. It describes two methods for shapes or sections: universal rolling and caliber rolling. The article provides information on two-high mills and three-high mills. Specialty mills for thin sheets, namely, the Sendzimir mill and planetary mill, are discussed. The article analyzes the components of a computer controlled system for high-speed mills. Steels and nonferrous materials are also discussed. The article concludes with information on the defects in flat, bar, or shaped products due to heating and rolling practices.

Titanium metal passes through three major steps during processing from ore to finished product: reduction of titanium ore to sponge (porous form), melting of sponge and scrap to form ingot, and remelting and casting into finished shape. This article describes primary fabrication, including all operations that convert ingot into general mill products, such as billet, bar, plate, sheet, strip, tube, and wire. The section on secondary fabrication describes processes such as die forging, extrusion, hot and cold forming, machining, chemical milling, and joining. The article presents a short note on powder metallurgy products of titanium. Casting processes and properties are covered in the final section.

This article discusses the classification, characteristics and temper designations of wrought aluminum alloys. Wrought aluminum products are available as flat-rolled products such as sheets, plates, and foils; rods, bars, and wires; tubular products such as tubes and pipes; extruded shapes; forgings; and impacts. The article provides information on product economics, design and selection, including product dimension and dimension tolerances, and design and use of wrought product capabilities. Finally, it tabulates the specifications and standards for aluminum mill products.

This article is a comprehensive collection of property data for wrought aluminum and aluminum alloys. Data are provided for the physical properties and mechanical properties of wrought aluminum and aluminum alloys. The listing also includes values that indicate the effect of temperatures on tensile strength, yield strength, and elongation, and the mechanical properly limits for aluminum alloy die forgings, non-heat-treatable and heat-treatable aluminum alloy sheets and plates, and non-heat-treatable aluminum alloy extruded wires, rods, bars, and shapes.

This article discusses the processes involved in continuous hotdip coating of steel sheets, namely, hot and cold line processing, surface preparation, and post treatment. It outlines the properties and microstructures of metals and their alloys used in this process. The coatings considered in this article include metal coatings, such as zinc coatings, and alloy coatings, such as zinc-iron, types 1 and 2 aluminum, Zn-5AI, Zn-55AI, and lead-tin coatings.

Porcelain enamels are glass coatings applied primarily to products or parts made of sheet steel, cast iron, and aluminum to improve appearance and to protect the metal surface. This article describes the types of porcelain enamels, and details enamel frits for these materials. It provides a list of steels suitable for porcelain enameling and discusses the most important factors considered in the selection of steel for porcelain enameling. The article briefly presents the preparation methods of these materials for porcelain enameling and covers the methods, and furnaces of porcelain enameling. It examines the role of coating thickness, firing time and temperature, metal substrate, and color on the performance of enameled surfaces. The article concludes with a discussion on the properties of enameled surfaces, factors considered in process control, and test procedures for evaluating the quality of enameled surfaces.

Ferrous metals are metals that contain primarily iron and may have small amounts of other elements added to give the desired properties. This article discuses the characteristics of steel products used in most industries, including construction, automotive, energy, shipping, and agriculture. These products include bars, rods, wires, hot and cold rolled sheets, strip plates, tin mill products, steel tubes, castings, and forgings. The article also provides information on the methods used to prevent or control the rusting of ferrous materials, namely, alloying, coating, and covering.

This article describes the paint systems generally used to protect steel structures, steel sheet, and bridges from corrosion, and how they deter corrosion. It provides a discussion on the basic design criteria of steel structures for corrosion protection. The article also explains the differences between prepaint and postpaint, and the steps involved in prepaint processing of steel. It presents the selection guideline for paint system evaluation. The advantages of corrosion protection are also discussed.

The basic quality analysis tools are cause-and-effect diagrams, check sheets, control charts, histograms, Pareto charts, scatter diagrams, and run charts. This article reviews how the basic quality analysis tools are built upon to become a more advanced set of quality tools. It describes the advanced quality tools: advanced product quality planning, failure mode and effects analysis, control planning, measurement systems analysis, lean tools, statistical process control, production viability and tryout, and Six Sigma.

This article presents the Schmid's law that describes the response of crystal structures to loading. It describes the Taylor model to calculate the uniaxial yield stress of an isotropic face-centered cubic aggregate in terms of critical resolved shear stress. The article discusses the stress-based approach of the Bishop and Hill procedure to directly find stress states that could simultaneously operate at least five independent slip systems. It presents ways to find isostress or lower-bound yield loci for sheets having single-crystal orientation.