1-20 of 7090

Search Results for selected

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 1986
Fig. 94 Three-element (Ni-Cr-Mo) isothermal sections at selected temperatures. (a) 1523 K isothermal section. (b) 1123 K isothermal section. Source: Ref 63 More
Image
Published: 01 January 1986
Fig. 20 Auger point analysis of the six selected points shown in Fig. 19 . (a) Point 1: the long rod-shaped precipitate is a beryllium sulfide. (b) Point 2: this small round precipitate is a titanium carbide. (c) Point 3: this small irregular precipitate is also a titanium carbide. (d) Point More
Image
Published: 01 January 1986
Fig. 36 Auger depth profiles of three selected locations on the cam lobe shown in Fig. 35(a) . Etch rate was 4 nm/min for the first 4 min and 8 nm/min thereafter. Right-hand profiles are expansions of the vertical axes to give detail on minor elements. More
Image
Published: 31 October 2011
Fig. 8 Droplet sizes attainable under selected current pulsing conditions in gas metal arc welding of steel. Source: Ref 4 More
Image
Published: 31 October 2011
Fig. 29 Typical variation of selected weld-metal properties with oxygen content in ferritic steel weld metals. (a) Plot of Charpy V-notch (CVN) impact test upper-shelf energy versus oxygen content. (b) Plot of CVN transition temperature versus oxygen content. HAZ, heat-affected zone. Source More
Image
Published: 31 October 2011
Fig. 33 Plot of impact energy versus acicular ferrite content for selected carbon contents at −60 °C (−76 °F). Source: Ref 36 More
Image
Published: 31 October 2011
Fig. 34 Schematic showing heat-affected zone (HAZ) microstructure in selected high-heat-input welds. (a) Titanium oxide steel. (b) Titanium nitride steel. AF, acicular ferrite; UB, upper bainite. Source: Ref 44 More
Image
Published: 31 October 2011
Fig. 3 Plot of selected parameters versus time relative to the three phases of the direct-drive friction welding process More
Image
Published: 31 October 2011
Fig. 4 Plot of selected parameters versus time relative to the two phases of the inertia-drive friction welding process More
Image
Published: 31 October 2011
Fig. 8 Plot of arc voltage versus arc current for selected inert shielding gases. Welding parameters: anode, titanium; cathode, tungsten; polarity, direct current electrode negative; arc length, 12.7 mm (0.050 in.) More
Image
Published: 01 December 2008
Fig. 2 Stress-strain curves for selected steels showing influence of carbon content. Source: Ref 2 More
Image
Published: 01 December 2008
Fig. 2 Stress-rupture for 1000-h life of selected cast nickel-base heat-resistant alloys More
Image
Published: 01 December 2008
Fig. 1 Effect of carbon equivalent on no-crack temperature for selected grades of iron castings. Source: Ref 1 More
Image
Published: 01 December 2008
Fig. 20 Standard magnetization curves for selected iron-base alloys. Source: Ref 13 More
Image
Published: 01 August 2013
Fig. 1 Galvanic series of selected metals and alloys in seawater showing their corrosion potentials. Adapted from Ref 4 More
Image
Published: 01 August 2013
Fig. 4 Estimated service life of Zn-15Al thermal spray coating in selected environments for a given coating thickness. Sealed coatings are recommended for saltwater immersion service. Adapted from Ref 14 More
Image
Published: 01 August 2013
Fig. 5 Estimated service life of aluminum thermal spray coating in selected environments for a given coating thickness. For wear, abrasion, and impact applications, Al-10%Al 2 O 3 is preferred. Adapted from Ref 14 More
Image
Published: 30 September 2014
Fig. 3 Specific heat versus temperature for selected steels. Source: Ref 4 More
Image
Published: 01 January 1994
Fig. 8 Special mask made of molded rubber for shot peening a selected area and for holding the work during peening More
Image
Published: 01 January 1994
Fig. 14 Corrosion resistance of selected metal finishes relative to type of phosphate coating applied. (a) Black stain. (b) Corrosion-preventing oil. (c) Black stain and oil. Source: Ref 7 More