1-20 of 496 Search Results for

rising step-load test

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003243
EISBN: 978-1-62708-199-3
... information on the cantilever beam test, wedge-opening load test, contoured double-cantilever beam test, three-point and four-point bend tests, rising step-load test, disk-pressure test, slow strain-rate tensile test, and potentiostatic slow strain-rate tensile test for hydrogen embrittlement. constant...
Series: ASM Handbook
Volume: 13A
Publisher: ASM International
Published: 01 January 2003
DOI: 10.31399/asm.hb.v13a.a0003667
EISBN: 978-1-62708-182-5
... beam tests, rising step-load tests, and slow strain rate tensile tests. It also describes the interpretation of test results and how to control hydrogen embrittlement during production. cantilever beam test contoured double-cantilever beam test hydrogen hydrogen embrittlement rising step-load...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003436
EISBN: 978-1-62708-195-5
... Abstract This article introduces the principal methodologies and some technologies that are being applied for nondestructive evaluation of composite materials. These include ultrasonic testing (UT), air-coupled UT, laser UT, ultrasonic spectroscopy, leaky lamb wave method, acousto...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006778
EISBN: 978-1-62708-295-2
... or wedge-shaped cracks at grain triple points • Reaction scales or internal precipitation • Some cold flow in last stages of failure Contributing factors • Load exceeded the strength of the part • Check for proper alloy and processing by hardness check or destructive testing, chemical analysis...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002360
EISBN: 978-1-62708-193-1
..., this percentage can be decreased. The amount of crack extension between each load decrease must also be controlled. If the step is too small, the influence of the plastic zone ahead of the crack may still be present. To avoid transient (load-sequence) effects in the test data, as discussed above, the...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005292
EISBN: 978-1-62708-187-0
... extraction, die lubrication, insert loading, and die close. Some manual aspects of the operations together with automation options are discussed. The article describes finishing steps, such as finish trimming, detailed deflashing, shot blast cleaning, and quality checks. Automation of the postcasting process...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001809
EISBN: 978-1-62708-180-1
... presents the steps for failure analysis of sliding bearings. It also reviews the factors responsible for bearing failure with examples. aluminum alloys babbitts bronze contaminants copper-lead bearing alloys elasto-hydrodynamics failure analysis fluid-film lubrication grooves load-carrying...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003442
EISBN: 978-1-62708-195-5
... to that used in a hardness test, is applied to the specimen under constituent load, and the specimen is heated. Near the T g , the probe will begin to penetrate the surface of the sample, causing an inflection on the TMA curve. Like flexure TMA, the results depend highly on the applied load and...
Series: ASM Handbook
Volume: 18
Publisher: ASM International
Published: 31 December 2017
DOI: 10.31399/asm.hb.v18.a0006402
EISBN: 978-1-62708-192-4
... and a similar working point in the Stribeck curve—to be obtained through an appropriate similarity in the kinematics and the suitable choice of load ( F N ), velocity ( v ), temperature ( T ), and test duration ( t ) (as described in the preceding article, “Introduction to Tribology and Tribological...