1-20 of 637 Search Results for

resin bonds

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 December 2008
Fig. 8 Baking speeds of phenolic-resin-bonded versus oil-bonded sand cores More
Image
Published: 01 January 1989
Fig. 11 Dry cutoff of a pipe using a reinforced resin bond wheel More
Image
Published: 01 January 1989
Fig. 13 Use of a type 27 reinforced resin bond abrasive wheel to grind welds More
Image
Published: 01 January 1989
Fig. 15 Floorstand rough grinding of a casting using a zirconia-alumina resin bond wheel. Note the pressure bar used to increase the grinding rate. More
Image
Published: 01 November 1995
Fig. 13 Grindability survey comparing resin-bonded wheels containing 150-grit metal coated abrasives to evaluate capabilities of both friable diamond and cubic boron nitride (CBN) abrasives in grinding technical ceramics. (a) Grinding ratio. (b) Specific energy. The specific grinding rate, Q More
Image
Published: 31 December 2017
Fig. 2 Microstructures of (a) resin-bonded and (b) sintered brake friction materials More
Image
Published: 31 December 2017
Fig. 3 Microstructures of organic resin-bonded brake linings. (a) Non-asbestos organic (NAO). (b) Low-met. (c) Semi-met More
Image
Published: 30 September 2015
Fig. 1 Structure of metallic friction materials. (a) Resin-bonded brake pad. (b) Sintered brake pad More
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005241
EISBN: 978-1-62708-187-0
... resins; shell molding of sand with a thin resin-bonded shell; no-bond vacuum molding of sand; plaster-mold casting; ceramic-mold casting; rammed graphite molding; and magnetic (no-bond) molding of ferrous shot. The article tabulates a general comparison of casting methods and discusses the basic...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003172
EISBN: 978-1-62708-199-3
..., dry sand molds, resin-bonded sand molds, and sodium silicate bonded sand. The article describes the casting processes that use these molds, including the no-bake process, cold box process, hot box process, the CO2 process, lost foam casting process and vacuum molding process. The casting processes...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005242
EISBN: 978-1-62708-187-0
..., are discussed. The article describes the methods of sand bonding with inorganic compounds. It provides a description of resin-bonded sand systems: no-bake binder systems, heat-cured binder systems, and cold box binder systems. The article concludes with a discussion on the media used for expendable molds...
Image
Published: 01 January 1990
Fig. 9 Commercially available diamond grains used in various applications. (a) Friable diamond grains especially tailored for resin bond grinding wheels. (b) Diamond grains tailored for use in metal bond grinding wheels. These grains are typically in the 80 to 400 mesh size (350 to 38 μm More
Image
Published: 01 December 2008
Fig. 11 Sample cup for thermal analysis measurements of composition in cast irons. The resin-bonded sand cup has a chromel-alumet thermocouple. Courtesy of C.R. Loper, Jr., University of Wisconsin More
Image
Published: 01 November 1995
Fig. 8 Plot of surface finish (roughness average, R a ) versus downfeed (depth of cut) for three ceramics that were surface ground with a resin bonded diamond wheel. HPSN, hot-pressed silicon nitride. Source: Ref 13 More
Image
Published: 31 August 2017
Fig. 6 Change in skin features as a function of the distance from the mold-metal interface for spheroidal graphite (SG) iron 6 mm (0.24 in.) plates (3.67% C, 2.92% Si, 0.04% Mg) poured in alkyd-urethane resin-bonded molds. (a) Graphite shape and area. (b) Percent pearlite and microhardness More
Series: ASM Handbook
Volume: 2
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v02.a0001106
EISBN: 978-1-62708-162-7
... applications Superabrasive Bond U.S. mesh size ranges 20–30 30–40 40–50 50–60 60–80 80–100 100–120 120–140 140–170 170–200 200–230 230–270 270–325 325–400 Diamond Resin/vitreous X X X X X X X X X Diamond Metal X X X X X X X X X CBN Resin/vitreous...
Image
Published: 01 January 1989
Fig. 35 Effect of truing infeed on truing force. A, resin and metal bond CBN wheel; B, vitrified CBN wheel; C, conventional vitrified wheel More
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002151
EISBN: 978-1-62708-188-7
... be used at speeds higher than the rated speed shown on the grinding wheel.) Conventional abrasive grinding wheels are held together by two types of bond: vitrified and organic. Organic bonds are further divided into resin bond (and its subgroup plastic bond), rubber, and shellac. In addition...
Book Chapter

By K. Subramanian
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002152
EISBN: 978-1-62708-1