This article discusses the concepts of quality control (QC) and quality assurance (QA), and clarifies the differences and similarities in the roles and responsibilities of QC and QA personnel. It describes the inspection procedures used to verify proper surface preparation and installation of the protective coating/lining system. Prior to beginning surface-preparation operations, many specifications will require a presurface-preparation inspection to verify the correction of fabrication defects and removal of surface contamination such as grease, oil, cutting compounds, lubricants, and chemical contaminants. When inspecting concrete prior to coating installation, three areas of concern exist: surface roughness, moisture content in concrete, and acidity/alkalinity of the surface. The article provides information on the industry standards for assessing surface cleanliness. It details postcoating application quality requirements, including measuring of dry-film thickness, assessing intercoat cleanliness, verifying minimum and maximum recoat intervals, performing holiday/pinhole detection, conducting cure/hardness testing, and assessing adhesion of the applied coating system.

The basic elements of control design are safety, process control, process verification, machine control, productivity, repeatability, and ease of setup. Effective systems of quality control/quality assurance are essential for heat treating practices. This article provides information on process control modes, as well as on process signatures of some items that require control, monitoring, verifying, and logging methods. It provides information on programmable logic controllers that have become efficient in machine control and monitoring. The article describes possible noise issues, National Electric Code clearance requirements, monitoring requirements, and machine accuracy that need to be considered when designing induction equipment.

This article provides general guidelines for casting design to provide progressive solidification, minimize heat concentration, eliminate cores, and prevent distortion. Casting design also affects tolerances. Casting tolerances depend on the alloy being poured, the size of the casting, and the molding method used. Designers can predict the effect of the design on the structure of the final part using solidification simulation models, namely finite element and finite difference models, and rapid prototyping. The article concludes with a short note on how the quality is assured in the foundry.

This article presents the importance of progressing from post-manufacturing inspection/verification to in-process inspection/verification methods. It lists the various quality assurance factors considered for typical composite laminate lay-up process. The article provides information on composite cure tooling that is fabricated from steel, aluminum, or high-temperature composite materials. The quality assurance for commercial applications is reviewed. The article concludes with a discussion on data fusion systems designed to provide nondestructive analysis data from fabrication and assembly processes for each individual composite part.

This article describes the characterization techniques, mechanical tests, and nondestructive evaluation methods that are commonly used for metal-matrix composites. It also tabulates typical methods of particle size and size distribution measurement, as well as mechanical test specifications for aluminum-matrix composites.

This article defines quality, quality assurance, quality control, and quality management of processes, products, and services. It describes the evolution of quality control and quality assurance in the coatings industry. The article also discusses the standards, quality programs, and certifications in the coatings industry.

Heat treatment of aluminum alloys is assessed by various quality-assurance methods that include metallographic examination, hardness measurements, mechanical property tests, corrosion-resistance tests, and electrical conductivity testing. The use of hardness measurements in the quality assurance of heat treated aluminum products is effectively used in conjunction with the measurement of surface electrical conductivity. This article provides a detailed discussion of the error sources in eddy-current conductivity measurements. It also presents useful information on the variation of electrical conductivity of alloy 2024 samples as a function of aging time at different isothermal holding temperatures.

The process of coating plastics with metals for functional purposes is called metallizing of plastics. This article discusses the metallizing of plastics, provides information on its history, and gives a short note on applications and adhesion properties of metallic coatings. It also discusses the selection of plastics for plating. This article also describes metallizing techniques, including plating (electrolytic or electroplating), vacuum metallizing and thermal spraying, and environmental considerations. The article discusses the quality assurance procedures for metallized plastic parts which include tests that assess the quality of the finish, coating thickness, adhesion, and corrosion resistance, and gives a short note on service performance, which includes service condition classifications.

This article provides an overview of metal additive manufacturing (AM) processes and describes sources of failures in metal AM parts. It focuses on metal AM product failures and potential solutions related to design considerations, metallurgical characteristics, production considerations, and quality assurance. The emphasis is on the design and metallurgical aspects for the two main types of metal AM processes: powder-bed fusion (PBF) and directed-energy deposition (DED). The article also describes the processes involved in binder jet sintering, provides information on the design and fabrication sources of failure, addresses the key factors in production and quality control, and explains failure analysis of AM parts.

This article briefly introduces the concepts of failure analysis, including root-cause analysis (RCA), and the role of failure analysis as a general engineering tool for enhancing product quality and failure prevention. It initially provides definitions of failure on several different levels, followed by a discussion on the role of failure analysis and the appreciation of quality assurance and user expectations. Systematic analysis of equipment failures reveals physical root causes that fall into one of four fundamental categories: design, manufacturing/installation, service, and material, which are discussed in the following sections along with examples. The tools available for failure analysis are then covered. Further, the article describes the categories of mode of failure: distortion or undesired deformation, fracture, corrosion, and wear. It provides information on the processes involved in RCA and the charting methods that may be useful in RCA and ends with a description of various factors associated with failure prevention.

Forgings are classified in various ways, beginning with the general classifications open die and closed die. They are also classified according to how they are made; such as hammer upset forgings, ring-rolled forgings, and multiple-ram press forgings; and in terms of the close-to-finish factor or amount of stock that must be removed to satisfy the dimensional and detail requirements of the finished part. In addition to types and classifications, the article discusses critical design factors and ways to ensure that the resulting forgings measure up to metallurgical, mechanical property, and dimensional accuracy requirements. The responsibility for design verification is vested in material control, which depends on the proper application of drawings, specifications, manufacturing process controls, and quality assurance programs. The article addresses each of these areas as well as related topics; including stress-induced fatigue failure, tolerances, machining allowances; and the fundamentals of hammer and press forgings, hot upset forgings, and hot extrusion forgings.

This article provides information on the process details that differ from general water atomization of metals as they relate to basic and engineering properties that are specific to stainless steel powders. The discussion focuses on the compacting-grade stainless steel powders. The process details include raw materials, melting method, and control of physical and chemical powder characteristics. The article describes the gas atomization of stainless steel powders and processes that are done after water atomization: drying, screening, annealing, and lubricating. It also discusses the two types of quality assurance testing measures for powder metallurgy stainless steels: tests for powder contamination and tests of chemical and physical properties.

Powder forging is a process in which unsintered, presintered, and sintered powder metallurgy preforms are hot formed in confined dies. This article provides information on the basic forms of powder forging and describes the material considerations, process considerations, and mechanical properties of powder forged (PF) steels. It reviews the parameters involved in quality assurance tests for PF parts. The article includes examples of PF components and highlights the reasons for selecting them over those made by competing forming methods.

Powder forging is an extension of the conventional press and sinter powder metallurgy process, which is recognized as an effective technology for producing a variety of parts to net or near-net shape. This article focuses on the material considerations, such as powder characteristics, alloy development, and inclusion assessment; and process considerations, such as process stages, tool design, and secondary operations; of ferrous alloy powder forging. The mechanical properties of powder forged materials are also reviewed. The article discusses the quality assurance tests for powder forged materials: the part dimensions and surface finish measurement, magnetic particle inspection, metallographic analysis, and nondestructive testing. It concludes with a discussion on the applications of powder forged parts with examples.

Forging is the process of working hot metal between dies, usually under successive blows and sometimes by continuous squeezing. This article describes the material selection criteria, quality assurance tests for forged components, and the dimensional tolerances of closed-die steel forgings. It provides an overview of the mechanical properties of wrought materials. The article also includes information on the fundamentals of hammer and press forgings and the design of hot upset forgings.

Liquid penetrant inspection is a nondestructive method of revealing discontinuities that are open to the surfaces of solid and essentially nonporous materials. This article provides information on physical principles, evolution, description, and processing parameters of liquid penetrant inspection as well as materials used. It discusses some of the more generally used types of equipment used in penetrant inspection and their requirements. The article describes various penetrant methods and their selection criteria and provides information on precleaning and postcleaning of workpieces before and after penetrant inspection. The quality assurance and maintenance of penetrant inspection materials are also discussed. The article concludes with information on specifications and standards applicable to penetrant inspection.

The characterization, testing, and nondestructive evaluation of ceramics and glasses are vital to manufacturing control, property improvement, failure prevention, and quality assurance. This article provides a broad overview of characterization methods and their relationship to property control, both in the production and use of ceramics and glasses. Important aspects covered include the means for characterizing ceramics and glasses, the corresponding rationale behind them, and relationship of chemistry, phases, and microconstituents to engineering properties. The article also describes the effects that the structure of raw ceramic materials and green products and processing parameters have on the ultimate structure and properties of the processed piece. The effects that trace chemistry and processing parameters have on glass properties are discussed. The article describes mechanical tests and failure analysis techniques used for ceramics.

This article provides a detailed account of particle-induced x-ray emission (PIXE), covering the basic principles of PIXE analysis and calibration and quality-assurance protocols employed. A comparative study on PIXE and x-ray fluorescence is then presented. The article also discusses the applications of PIXE in atmospheric physics and chemistry, external proton milliprobes and historical analysis, and PIXE microprobes.

The purpose of accreditation is to evaluate and assure high-quality results from suppliers of products or services without incurring the costs associated with auditing each supplier. This article describes laboratory accreditation based on the general requirements of International Organization for Standardization/International Electrotechnical Commission (ISO/IEC) Guide 25, "General Requirements for the Competence of Calibration and Testing Laboratories." The Guide 25 is a balanced standard that addresses quality system requirements of ISO 9000 and the technical requirements needed to perform testing or calibration. The article describes an accreditation process that would enhance the international acceptance of test data for mechanical testing laboratories.