Search Results for pin fasteners

This article discusses different types of mechanical fasteners, including threaded fasteners, rivets, blind fasteners, pin fasteners, special-purpose fasteners, and fasteners used with composite materials. It describes the origins and causes of fastener failures and with illustrative examples. Fatigue fracture in threaded fasteners and fretting in bolted machine parts are also discussed. The article provides a description of the different types of corrosion, such as atmospheric corrosion and liquid-immersion corrosion, in threaded fasteners. It also provides information on stress-corrosion cracking, hydrogen embrittlement, and liquid-metal embrittlement of bolts and nuts. The article explains the most commonly used protective metal coatings for ferrous metal fasteners. Zinc, cadmium, and aluminum are commonly used for such coatings. The article also illustrates the performance of the fasteners at elevated temperatures and concludes with a discussion on fastener failures in composites.

This article first provides an overview of the types of mechanical fasteners. This is followed by sections providing information on fastener quality and counterfeit fasteners, as well as fastener loads. Then, the article discusses common causes of fastener failures, namely environmental effects, manufacturing discrepancies, improper use, or incorrect installation. Next, it describes fastener failure origins and fretting. Types of corrosion in threaded fasteners and their preventive measures are then covered. The performance of fasteners at elevated temperatures is addressed. Further, the article discusses the types of rivet, blind fastener, and pin fastener failures. Finally, it provides information on the mechanism of fastener failures in composites.

This article compares and contrasts mechanical joining techniques used in the manufacture of aluminum assemblies, including seaming, swaging, flanging, crimping, clinching, dimpling, interference and snap fits, and interlocking joints. It provides basic illustrations of the various methods and summarizes the advantages and disadvantages of each. The article also discusses the use of staples, nails, rivets, and threaded fasteners and provides relevant property and performance data.

This article discusses the effect of thread design, preload, tightening, and mean stress on the fatigue strength of bolt steel. It describes the factors influencing fatigue failures in cold-driven and hot-driven riveted joints. The factors affecting the fatigue resistance of bolted friction joints are also discussed. The article reviews stress concentrations in pin joints and discusses stress-intensity factors for mechanically fastened joints.

Aluminum wrought products, castings, welds, and fasteners are used in many structural applications where they are required to safely support a load. It is useful to design aluminum structural components with its structural properties in mind from conceptualization rather than attempting to mimic components of other materials. This article discusses design specifications, design requirements and methods, and material properties used in aluminum structural design. These properties include tensile yield strength and tensile ultimate strength, welding, and ductility. The article describes various factors that affect the strength of two categories of aluminum structural components, namely members and connections. Design requirements for aluminum bolts, rivets, screws, and pins are provided. The article concludes with a discussion on the considerations for serviceability, namely deflections and vibrations.

This article focuses on the factors to be considered for selecting fasteners for joining carbon fiber composites. These considerations include corrosion compatibility, fastener materials, strength, stiffness, head configurations, importance of clamp-up, hole fit, and lightning protection.

This article discusses different types of joining processes, including welding, brazing, soldering, mechanical fastening, and adhesive bonding. It examines two broad classes of welding: fusion welding and solid-state welding. The article discusses the process selection considerations for welding, brazing, and soldering. It also describes joint design considerations such as selection of weld joints and welds.

This article explains how to design a joint or conduct a joining process so that components can be produced most efficiently and without defects. The joining processes include mechanical fastening, adhesive bonding, welding, brazing, and soldering. The article discusses the selection and application of good design practices based on the understanding of process-related manufacturing aspects such as accessibility, quality, productivity, and overall manufacturing cost. It provides several examples of selected parts and joining processes to illustrate the advantages of a specific design practice in improving manufacturability.

Cold heading is typically a high-speed process where a blank is progressively moved through a multi-station machine. This article discusses various cold heading process parameters, such as upset length ratio, upset diameter ratio, upset strain, and process sequence design. It describes the various components of a cold-heading machine and the tools used in the cold heading process. These include headers, transfer headers, bolt makers, nut formers, and parts formers. The article explains the operations required for preparing stock for cold heading, including heat treating, drawing to size, machining, descaling, cutting to length, and lubricating. It lists the advantages of the cold heading over machining. Materials selection criteria for dies and punches in cold heading are also described. The article provides examples that demonstrate tolerance capabilities and show dimensional variations obtained in production runs of specific cold-headed products. It concludes with a discussion on the applications of warm heading.

Detailed analyses and test correlations are typically required to support design development, structural sizing, and certification. This article addresses issues concerning building block levels ranging from design-allowables coupons up through subcomponents, as these levels exhibit a wide variety of test-analysis correlation objectives. At these levels, enhanced analysis capability can be used most effectively in minimizing test complexity and cost while also reducing design weight and risk. The article discusses the examples of tests for which good correlative capability has shown significant benefit. These include notched (open and/or filled hole) tension and compression, inter/intralaminar shear and tension, and pin bearing.

Vertical centrifugal casting machines, installed below the ground level for maximum operator safety, are used for producing bushings and castings that are relatively large in diameter and short in length. This article discusses the mold design for different types of sand molds and permanent molds and their production considerations. It describes the speed of rotation, mold speeds curves, and pouring techniques that are considered in the operation of vertical centrifugal casting machines.

This article is an atlas of fractographs that helps in understanding the causes and mechanisms of fracture of titanium alloys and in identifying and interpreting the morphology of fracture surfaces. The fractographs illustrate the fracture surface, fatigue crack growth, intergranular fracture, crack propagation, ductile overload fracture, dimpled rupture, microvoid coalescence, and quasi-cleavage fracture of these alloys.

Good hole-drilling processes are key to joining composite parts with other composite parts or with metal parts. This article discusses the considerations for drilling polymer-matrix composites. It describes the use of power-feed drill motors and automated drilling/fastener installation equipment. The article provides a discussion on reaming, countersinking, and three recommended choices of cutting tools for producing a countersink in carbon/epoxy structure. The cutting tools include: standard carbide insert cutters, solid carbide cutters, or polycrystalline diamond (PCD) insert cutters. The article concludes with a discussion on inspection of hole quality.

This article focuses on the corrosion and deterioration of components on recreational and small workboats. It discusses the materials selection and corrosion control for the components. These components include hulls, fittings, fasteners, metal deck gear, winches, backing plates, lifeline supports, inboard engines, cooling systems, propulsion systems, electrical and electronic systems, plumbing systems, masts, spars, and rigging.

Joining is key to the manufacture of large or complex devices or assemblies; construction of large and complex structures; and repair of parts, assemblies, or structures in service. This article describes the three forces for joining: physical, chemical, and mechanical. It provides an overview of the joining processes, namely, mechanical fastening, integral attachment, adhesive bonding, welding, brazing, and soldering. The article concludes with information on the various aspects of joint design and location that determine the selection of a suitable joining method.

This article schematically illustrates the basic types of drafts used in forging design, including outside draft, inside draft, blend draft, natural draft, shift draft, and back draft. The amount of draft, or the draft angle, is designated in degrees and is measured from the axis of a hammer or press stroke. The article illustrates the measurement of draft angle by describing the designs of forgings produced in equipment with vertical and horizontal rams. The use of excessive amounts of draft usually results in an increase in overall cost. The article describes various alternatives for reducing or eliminating draft. It provides a checklist citing major items that should be coordinated with a designer's review of draft.

This article provides a discussion on adhesively bonded joints and elastic-plastic mathematical model for an adhesive in shear. It discusses the design rules for thin bonded structures and reviews computer programs for the highly loaded stepped-lap joints. The article describes the two-dimensional effects associated with load redistribution around flaws and with damage tolerance. The elastic-isotropic geometric stress-concentration factors and empirically established correlation factors of mechanically fastened joints are discussed. The article provides information on the identification of optimal joint proportions for single-row joints, and the design and analysis of the stronger multirow joints, with particular regard to the bearing-bypass interaction.

This article explores why structural element and subcomponent testing are conducted. It discusses the different types of failure modes in composites, and provides information on the testing methodology, fixturing, instrumentation, and data reporting. The article reviews various standard elements used to characterize composite materials for the various failure modes. Simple structural-element testing under in-plane unidirectional, multidirectional, and combined loading, as well as out-of-plane loading are discussed. Simple bolted and bonded joints, as well as data correlation are reviewed with analytical predictions. The article also provides a list of the ASTM testing standards applicable at the element level of testing for both polymer-matrix composites and metal-matrix composites. It concludes with a discussion on durability and damage tolerance testing.