Skip Nav Destination
Close Modal
Search Results for
perforations
Update search
Filter
- Title
- Authors
- Author Affiliations
- Full Text
- Abstract
- Keywords
- DOI
- ISBN
- EISBN
- Issue
- ISSN
- EISSN
- Volume
- References
Filter
- Title
- Authors
- Author Affiliations
- Full Text
- Abstract
- Keywords
- DOI
- ISBN
- EISBN
- Issue
- ISSN
- EISSN
- Volume
- References
Filter
- Title
- Authors
- Author Affiliations
- Full Text
- Abstract
- Keywords
- DOI
- ISBN
- EISBN
- Issue
- ISSN
- EISSN
- Volume
- References
Filter
- Title
- Authors
- Author Affiliations
- Full Text
- Abstract
- Keywords
- DOI
- ISBN
- EISBN
- Issue
- ISSN
- EISSN
- Volume
- References
Filter
- Title
- Authors
- Author Affiliations
- Full Text
- Abstract
- Keywords
- DOI
- ISBN
- EISBN
- Issue
- ISSN
- EISSN
- Volume
- References
Filter
- Title
- Authors
- Author Affiliations
- Full Text
- Abstract
- Keywords
- DOI
- ISBN
- EISBN
- Issue
- ISSN
- EISSN
- Volume
- References
NARROW
Format
Topics
Book Series
Date
Availability
1-20 of 291 Search Results for
perforations
Follow your search
Access your saved searches in your account
Would you like to receive an alert when new items match your search?
1
Sort by
Image
Published: 01 January 2006
Fig. 8 Example of a 4130 cylinder given multiple perforations in a single explosive operation. Source: Ref 17
More
Image
in High-Strength Structural and High-Strength Low-Alloy Steels
> Properties and Selection: Irons, Steels, and High-Performance Alloys
Published: 01 January 1990
Fig. 28 Profiles of the fluted and perforated interlocking galvanized steel corrugated roof panels. All dimensions are given in millimeters. (a) D-200 roof panel, 600 mm (24 in.) wide coverage. (b) D-150 roof panel, 450 mm (18 in.) wide coverage
More
Image
Published: 01 January 2006
Fig. 10 Perforated nonmetallic pipe for monitoring the CP potentials under the tank bottom. Source: Ref 2
More
Image
Published: 01 January 2006
Fig. 7 Corrosion perforation of (a) aluminum impeller and (b) aluminum cover of a coolant pump resulting from a used and degraded engine coolant
More
Image
Published: 01 January 2006
Fig. 8 Nucleate boiling-induced cavitation corrosion caused perforation at the exhaust valve port of this aluminum cylinder head.
More
Image
Published: 01 January 2005
Fig. 43 Gas composition and progress of reactions for a sintering experiment performed with pure hydrogen. Source: Ref 14
More
Image
Published: 01 January 2005
Fig. 3 The owner complained about the serious rusting and perforation to the rear of his 4 by 4 vehicle after approximately 2 years of use. Subsequent review revealed that the vehicle was used to tow and launch a boat directly into the ocean each weekend during the spring, summer, and fall
More
Image
Published: 01 January 2005
Fig. 66 The perforated screen supported a carbon bed through which solvent-laden gases pass. Subsequently, the gas stream switched to steam that strips the solvent from the carbon bed, which can then be used again. The screen failed because of stress-corrosion cracking (SCC) resulting from
More
Image
Published: 01 January 2006
Fig. 26 Nucleate boiling-induced cavitation corrosion caused perforation at the exhaust valve port of this aluminum cylinder head. See the article “Engine Coolants and Coolant System Corrosion” in this Volume.
More
Image
Published: 01 January 2002
Fig. 26 Carbon steel superheater tube. Pitting corrosion and perforation were caused by the presence of oxygenated water during idle periods.
More
Image
Published: 01 January 2002
Fig. 40 Views of a through-wall perforation of a chromium-plated α brass (70Cu-30Zn) tube removed from a potable water system due to dezincification. (a) Macroview of tube. (b) Inside diameter surface of the tube shown in (a), depicting localized green deposits at the areas of dezincification
More
Image
Published: 01 January 2002
Fig. 3 Perforation near alloy 160 patch showing that the original 6.35 mm (0.250 in.) wall thickness had been reduced to 1.27 mm (0.050 in.) or less in the general area of failure
More
Image
Published: 01 January 2002
Fig. 19 Pitting and perforation on the outside of a carbon steel pipe
More
Image
Published: 01 January 2006
Fig. 17 Alloy 718 (UNS N07719) perforated sheet superplastically formed for an aircraft gas turbine tail cone skin. Courtesy of Special Metals Corporation
More
Image
Published: 01 January 2006
Fig. 18 Typical hardnesses for tool steel perforator punches. Regardless of material, punches should be tempered back to 56 to 60 HRC if they are to be subjected to heavy shock or used to pierce thick material.
More
Image
Published: 15 January 2021
Fig. 19 Pitting and perforation on the outside of a carbon steel pipe
More
Image
Published: 15 January 2021
Fig. 3 Perforation of alloy 690 incinerator liner near alloy 160 patch, showing that the original 6.35 mm (0.250 in.) wall thickness was reduced to approximately 1.27 mm (0.050 in.) or less in the general area of failure. Courtesy of U.S. Navy
More
Image
in Material Aspects of Additively Manufactured Orthopedic Implants of Titanium Alloys
> Additive Manufacturing in Biomedical Applications
Published: 12 September 2022
Fig. 4 Relationship between powder properties, bulk powder behavior, powder performance in the process, and the quality of the parts. (1) Reproducibility, layer density, layer continuity, and layer homogeneity; (2) apparent density, tap density, Hausner ratio. EBM, electron beam melting; PSD, p...
More
Book Chapter
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003117
EISBN: 978-1-62708-199-3
... Abstract Selection of appropriate grades of steel will enable the steel to perform for very long times with minimal corrosion, but an inadequate grade can corrode and perforate more rapidly than a plain carbon steel will fail by uniform corrosion. This article describes the effect of chemical...
Abstract
Selection of appropriate grades of steel will enable the steel to perform for very long times with minimal corrosion, but an inadequate grade can corrode and perforate more rapidly than a plain carbon steel will fail by uniform corrosion. This article describes the effect of chemical composition, heat treatment, welding, and surface condition on corrosion resistance of stainless steels. It discusses the various forms of corrosion and the important factors to be considered when selecting suitable stainless steel for application in specific corrosive environments.
Image
Published: 01 December 2004
Fig. 4 Equipment setup for electropolishing. Air agitation of electrolyte is provided through a perforated cathode. Detail at right shows an indirect electrical connection to a mounted specimen.
More
1
