1-20 of 547 Search Results for

parameter design

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 22A
Publisher: ASM International
Published: 01 December 2009
DOI: 10.31399/asm.hb.v22a.a0005412
EISBN: 978-1-62708-196-2
... number of atoms in a periodic cell of such a bicrystal lattice are designated Σ. For instance, a coincidence boundary Σ5 means that for each atom in coincidence in the two lattices, there are atoms in each lattice that are not coincident. Much research was focused on symmetric grain boundaries, where the...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004022
EISBN: 978-1-62708-185-6
... worker is a process simulation program that has the ability to simulate individual design trials. The master program controls the “search loop” and provides a set of process parameters to the worker for simulation. The worker program returns the results, which are used by the master to calculate the J...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004037
EISBN: 978-1-62708-185-6
... examples, with illustrations of parting line locations, accompanied by tables of design parameters. anisotropy cylindrical forgings draft forging process forging design grain flow parting line CONTROL OF GRAIN FLOW is one of the major advantages of shaping metal parts by rolling, forging, or...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004038
EISBN: 978-1-62708-185-6
..., metallurgical structure, measurement details, and design parameters, with supplementary data obtained from the examples of actual forgings. bosses forging forging design grain flow ribs RIBS AND BOSSES are integral functional elements or features of a forging that project outward from a web in a...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0009020
EISBN: 978-1-62708-187-0
... Abstract In terms of component design, casting offers a great amount of flexibility. This article discusses the parameters that can drive the geometry of casting design from a process standpoint. It provides information on the design of junctions and addresses considerations of secondary...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003088
EISBN: 978-1-62708-199-3
... available estimates of material properties, operating loads, and other design parameters. Once established, most of these estimated values have commonly been treated as fixed quantities or constants. This approach is called deterministic, in that each set of input parameters allows the determination of one...
Series: ASM Handbook
Volume: 20
Publisher: ASM International
Published: 01 January 1997
DOI: 10.31399/asm.hb.v20.9781627081948
EISBN: 978-1-62708-194-8
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003176
EISBN: 978-1-62708-199-3
... from a specific casting design and choice of casting process parameters. Some solidification models are capable of predicting distortion that will occur during casting and heat treatment and can be used to minimize residual stresses. Some commercial packages include expert systems to help orient the...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003060
EISBN: 978-1-62708-200-6
... inserts that form the ceramic blades to be pulled freely from between the blades without damaging the molded blades. This results in design compromises in aerodynamic performance. Disk rim configurations, blade-to-disk blending, and other parameters have been adjusted to facilitate the manufacture of a...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0009006
EISBN: 978-1-62708-185-6
... reductions consistent with standard gages, and the remaining design issues can be explained in terms of the Δ parameter. There are a wide variety of drawing technologies that benefit from low Δ process designs. With lower values of Δ (∼1.0 to 2.0), one reduces redundant work and general strain accumulation...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0009015
EISBN: 978-1-62708-187-0
... geometry for ductile iron may not be the same as that of cast aluminum bronze depending on key casting parameters such as pouring temperature, liquid-metal fluid life; solidification shrinkage, and formation of inclusions, slag or dross, in the melt. Design engineers thus need to know how suitable casting...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0003972
EISBN: 978-1-62708-185-6
... the overall system. Manufacturing process selection and parameters must meet these geometric requirements of overall shape, features, dimensions, and dimensional tolerances, depicted in Fig. 1a . Fig. 1 Connecting rod as a part design example. (a) Typical geometric dimensional requirements. (b...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003066
EISBN: 978-1-62708-200-6
... thus affect properties in similar ways. Traditionally, the structural role of a component in an oxide glass is designated as that of a glass former, a modifier, or an intermediate. Glass formers are those oxides that readily form a glass on their own, such as SiO 2 , B 2 O 3 , and GeO 2 . Modifiers...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004033
EISBN: 978-1-62708-185-6
... with radii for (a) corners and (b) fillets of actual aluminum alloy and steel forgings of all principal types. Data are derived from Table 1 and Table 2 Corners and fillets are secondary elements of a forging design. Design parameters for all primary elements of the...
Series: ASM Handbook
Volume: 4B
Publisher: ASM International
Published: 30 September 2014
DOI: 10.31399/asm.hb.v04b.a0005923
EISBN: 978-1-62708-166-5
... Abstract Quenchant agitation can be obtained by circulating quenchant in a quench tank through pumps and impellers. The selection of the agitation method depends on the tank design, type and volume of the quenchant, part design, and the severity of quench required. This article describes flow...