1-20 of 496 Search Results for

padding

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 December 2008
Fig. 5 Padding, properly placed, permitted production of this stainless steel sand casting to required soundness More
Image
Published: 01 December 2008
Fig. 6 Unusual padding of the center cavity of this stainless steel shell mold casting simplified production. Without the padding, complicated risering would have been necessary and would have caused high residual stresses. More
Image
Published: 01 December 2008
Fig. 10 Padding this aluminum permanent mold casting facilitated efficient foundry production. More
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005124
EISBN: 978-1-62708-186-3
... Abstract This article focuses on the three basic groups of flexible-die forming methods: rubber pad, fluid cell, and fluid forming. It provides information on the Guerin process, the Verson-Wheelon process, the trapped-rubber process, the Marform process, the Hydroform process, the SAAB process...
Image
Published: 31 December 2017
Fig. 7 Surface profiles of brake pad and disk rotor. (a) Pad, including two contact plateaus. (b) Contact plateau (friction layer) measured parallel and perpendicular to the sliding direction. (c) Disk measured parallel and perpendicular to the sliding direction. Source: Ref 5 More
Image
Published: 30 September 2015
Fig. 11 Extraction of soluble salts from surface using saturated contact pad More
Image
Published: 30 September 2015
Fig. 12 Concrete surface profile pads for International Concrete Repair Institute guideline 310.2. Courtesy of KTA-Tator, Inc. More
Image
Published: 15 June 2020
Fig. 10 Direct print to bare die using microdispensing. Bond pads are 100 μm. Photo by nScrypt More
Image
Published: 01 January 2006
Fig. 13 Scanning electron micrograph of corrosion products around bond pad on failed strain-gage-bridge die More
Image
Published: 01 December 1998
Fig. 31 Tooling and setup for rubber-pad forming by the Guerin process. Dimensions given in inches More
Image
Published: 01 December 1998
Fig. 32 Schematic of ASEA Quintus rubber-pad press with provision for heating difficult-to-form materials using infrared heater or heating elements contained in feed table More
Image
Published: 01 January 2006
Fig. 5 Wiping dies. (a) Die set for flanging with spring-loaded pressure pad to hold material flat during forming. (b) Die for wiping radius More
Image
Published: 01 January 2006
Fig. 16 Punch, die, and die pad used for the simultaneous lancing and forming of louvers in a press brake More
Image
Published: 01 January 2006
Fig. 18 Setups for rubber pad forming of various shapes in a press brake. (a) Simple 90° V-bend. Air space below die pad permits deep penetration. (b) Simple U-bend or channel. Spacers enable channels of varying widths to be formed in the same die-pad retainer. Deflector bars help to provide More
Image
Published: 01 January 2006
Fig. 1 Tooling and setup for rubber-pad forming by the Guerin process. Dimensions given in inches More
Image
Published: 01 January 2006
Fig. 6 Tooling and setup for rubber-pad forming by the Marform process More
Image
Published: 01 January 2006
Fig. 9 Schematic of ASEA Quintus rubber-pad hydraulic press with wire-wound frame More
Image
Published: 01 January 2006
Fig. 10 Schematic of ASEA Quintus rubber-pad press with provision for heating hard and brittle materials using infrared heater or heating elements contained in feed table More
Image
Published: 01 December 2004
Fig. 18 A transverse view of a titanium fiber metal pad (commercially pure titanium) attached to a titanium hip implant (Ti-6Al-4V) showing the metallurgical bonds between the titanium wires and the substrate More
Image
Published: 01 January 2001
Fig. 5 Use of skin pads for loading aircraft elevator More