1-20 of 87 Search Results for

nut projection

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 6A
Publisher: ASM International
Published: 31 October 2011
DOI: 10.31399/asm.hb.v06a.a0005626
EISBN: 978-1-62708-174-0
...-projection welding of heavy-, intermediate-, and thin-gage sheet mild steel as well as the welds between dissimilar thickness joints. The article also considers the solid-projection welding of steels: annular, nut, and cross-wire projection configurations. It also details the various tests that can be used...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001364
EISBN: 978-1-62708-173-3
.... References 1. Beneteau D. , Ed., Resistance Welding Manual , 4th ed. , G.H. Buchanan Co. , 1989 Examples of projection welding are shown in Fig. 3 . These applications, which range from sheet-to-sheet joints, to cross-wire welds, to annular attachments, to nut welds, to weld screws...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003323
EISBN: 978-1-62708-176-4
... setup may be specified, which then may be used for a series of tightening tests. In such cases, the bolt, nut, and washer all have the status of reference components. The bolt and nut assembly to be tested should be clamped into the apparatus so that the bolt end projects beyond the surface...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003502
EISBN: 978-1-62708-180-1
... design, and detail design, is reviewed. The article discusses the design process at the personal and project levels but takes into consideration the effects of some higher level influences and interfaces often found to contribute to engineering failures. conceptual design embodiment design...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002368
EISBN: 978-1-62708-193-1
... Steel Design, Ronald Press, 1974, p 519–551 Fig. 2 Axial fatigue strength at 10 7 cycles of bolt-nut assemblies with rolled threads and machined threads ( R = −1). Fig. 3 Fatigue life of riveted joints with different tension-shear-bearing ratios. Source: Ref 9 Abstract...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006501
EISBN: 978-1-62708-207-5
... to create permanent joints by locally deforming projections or rings into a suitable recess, such as with anchor bolts or rivet bushing (stake nut) fasteners ( Fig. 9 ). Fig. 9 Internally threaded rivet bushing (stake nut) joined to mating stamped sheet metal part Tube flanging joins together...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003223
EISBN: 978-1-62708-199-3
... during the design process. References 1. Beitz W. , Design for Ease of Recycling , J. Eng. Des. , Vol 4 ( No. 1 ), 1993 10.1080/09544829308914769 2. Froehlich D. , Renault Recycling Project: Global Initiatives from New Car Design to the End of the Life Cycle...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003223
EISBN: 978-1-62708-199-3
... to dismantle, using fasteners instead of weldments, screws instead of glue, and wing nuts instead of hex nuts, for example. In addition, components containing especially hazardous or ecologically harmful materials should be identified clearly and removed easily. A significant industry is already...
Series: ASM Handbook
Volume: 13A
Publisher: ASM International
Published: 01 January 2003
DOI: 10.31399/asm.hb.v13a.a0003689
EISBN: 978-1-62708-182-5
... ASTM A 563 for suitable bolt/nut combinations. Table 1 Properties of alloy layers to hot dip galvanized steels Layer Alloy Iron, % Melting point Crystal structure Diamond pyramid microhardness (vickers scale) Alloy characteristics °C °F Eta Zinc 0.03 419 787 Hexagonal...
Series: ASM Handbook
Volume: 4A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v04a.a0005790
EISBN: 978-1-62708-165-8
... sensitive. Although it is naïve to assume that a given time-temperature parameter applies to all of the subcritical annealing responses, some rough time-temperature trade-offs can be projected with the use of the Larson-Miller parameter, P , where: P = T ( log t + C ) where T...
Series: ASM Handbook
Volume: 5B
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v05b.a0006025
EISBN: 978-1-62708-172-6
... are being applied and if the painting work is being performed in the proximity of other operations, other project personnel, and/or the general public. As discussed earlier, not only can paint odors be a problem, but any dripping or airborne paint particulate (e.g., overspray) can be harmful to nearby...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006784
EISBN: 978-1-62708-295-2
.... 6 . When viewed in three dimension, this stereo pair shows a massive ridge running from top to bottom at the left, with pronounced cleavage steps on its right-hand slope. The corrosion debris remaining from service and extracted by the replica may be seen projecting from the surface. Transmission...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003552
EISBN: 978-1-62708-180-1
... properties of the material. Fig. 1 Cadmium-plated AISI 8740 steel nut that failed by hydrogen embrittlement. Failure occurred seven days after installation on an aircraft wing structure. See also Fig. 2. 5×. Courtesy of Lockheed-Georgia Company Hydrogen embrittles several metals and alloys...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003207
EISBN: 978-1-62708-199-3
... as weld time progresses. Figure 7 (d) shows the fully developed weld nugget. Applicability Projection welding is used where there is a high thickness ratio (for example, nuts welded to sheet), and where the appearance of the sheets must be controlled (for example, appliance surfaces...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003207
EISBN: 978-1-62708-199-3
.... Projection welding is used where there is a high thickness ratio (for example, nuts welded to sheet), and where the appearance of the sheets must be controlled (for example, appliance surfaces). The principal application of projection welding is the joining of stamped low-carbon, low-alloy, and HSLA steel...
Series: ASM Handbook
Volume: 2
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v02.a0001065
EISBN: 978-1-62708-162-7
..., nuts, pinions, tie rods, turnbuckle barrels, welding torch tips C19200 Excellent hot and cold workability. Uses: automotive hydraulic brake lines, flexible hose, electrical terminals, fuse clips, gaskets, gift hollowware, applications requiring resistance to softening and stress corrosion, air...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004004
EISBN: 978-1-62708-185-6
...-heading machine and the tools used in the cold heading process. These include headers, transfer headers, bolt makers, nut formers, and parts formers. The article explains the operations required for preparing stock for cold heading, including heat treating, drawing to size, machining, descaling, cutting...
Series: ASM Handbook
Volume: 5B
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v05b.a0006016
EISBN: 978-1-62708-172-6
... for quality control (QC) and/or quality assurance (QA) on coatings projects. Unfortunately, it is less common for specifications to define the specific and respective responsibilities of QC and QA personnel. All too often, the lines between QC and QA become blurred. This article discusses the concepts of QC...
Series: ASM Handbook
Volume: 20
Publisher: ASM International
Published: 01 January 1997
DOI: 10.31399/asm.hb.v20.a0002434
EISBN: 978-1-62708-194-8
... locking nut. Fig. 5 Two pulleys used in a product, each of a slightly different size. In the upper view, both pulleys use the same design D-hole for mounting on a shaft, and it is possible to put the wrong pulley on a shaft. In the lower view, each pulley has a different mounting hole...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003451
EISBN: 978-1-62708-195-5
... with Advanced Composite Material , The Design Council/Springer Verlag , 1989 Repair Types and Materials Training Major Standardization Issues Design Repair Materials Repair Techniques Inspection Training Analytical Repair Techniques Future Projects All documents mentioned...