1-8 of 8 Search Results for

nonlubricated wear

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004006
EISBN: 978-1-62708-185-6
..., titanium alloys, alloy steels, stainless steels, and tool steels are extruded with a variety of graphite and glass-base lubricants. Commercial grease mixtures containing solid-film lubricants, such as graphite, often provide little or no thermal protection to the die. For this reason, die wear is...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003104
EISBN: 978-1-62708-199-3
.... One of the simplest classifications of wear is based on the presence or absence of effective lubricants—namely, lubricated and nonlubricated wear. (The various types of lubrication are described later in this article.) Wear may also be classified by mechanisms. For example, the following wear mode...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0003842
EISBN: 978-1-62708-183-2
... applications involved heat engine components: ceramic gas turbines and adiabatic diesels ( Ref 126 , 127 ). Tribological, or friction and wear, properties are important characteristics for these and other applications involving sliding contact at high temperatures under dry, nonlubricated conditions...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001264
EISBN: 978-1-62708-170-2
... alloys, especially in Europe. Electroless nickel is an engineering coating, normally used because of excellent corrosion and wear resistance. Electroless nickel coatings are also frequently applied on aluminum to provide a solderable surface and are used with molds and dies to improve lubricity and...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001304
EISBN: 978-1-62708-170-2
... resulting property improvements (corrosion and/or wear resistance) will be stressed rather than the details of the process itself (equipment, plating bath compositions, process controls, etc.). Information on the surface engineering of stainless steels, tool steels, maraging steels, electrical steels, and...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003183
EISBN: 978-1-62708-199-3
.... Consequently, auxiliary impressions in the dies can be used to preform the billet to a shape that will best fill the finishing impressions in the dies. This helps create proper grain flow, soundness, and less scrap, with minimum die wear. When adequate preliminary impressions cannot be incorporated in the same...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003009
EISBN: 978-1-62708-200-6
... acetals include chain links, conveyor links and slats, cams, bearings, wear stops, pollution control equipment (for noise, air, and waste liquids), hose connectors, valve bodies, pumps (housings, pistons, valves, and impellers), and gears. Automotive applications that use the fuel resistance, low...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001308
EISBN: 978-1-62708-170-2
... compressive stresses that blasting sets up in the surface; coarse abrasives can wear through thin aluminum sections. Typical conditions for dry blasting with silica abrasive are given in Table 1 . Table 1 Conditions for abrasive blast cleaning of aluminum products with silica Grit size Mesh...