Inspection involves two types of testing, namely, destructive and non-destructive. This article provides an overview of the various inspection plans, such as first-article inspection and periodic tests done by destructive metallurgical testing and the final inspection done by the application of non-destructive technology. It describes the processes involved in destructive methods, such as surface hardness measurement, induction hardening pattern and heat-affected zone inspection, and the examination of microstructure before and after induction hardening. It also discusses non-destructive evaluation techniques for defect detection and microstructure characterization as well as non-destructive evaluation for real-time monitoring of induction process.

This article describes the two commonly used standardized tests for determining the mechanical properties of thermal spray coatings: hardness testing and tensile adhesion testing. It discusses the destructive and non-destructive methods of residual-stress measurement. Electrochemical testing methodologies include two distinctly different methods: direct and alternating current impedance techniques for assessing the corrosion resistance of coating attributes. The article also reviews the testing methods for determining thermomechanical and environmental stability of thermal barrier coatings. It discusses the wear testing methodologies that are standardized by ASTM, including the pin-on-disk, block-on-ring, dry sand/rubber wheel, erosion, metallographic apparatus abrasion, fretting wear, cavitation, reciprocating ball-on-flat, impact, and rolling contact fatigue test. The article concludes with a discussion on the methods of testing abradability and erosion resistance in abradable coatings.

Induction hardening of steel components is the most common application of induction heat treatment of steel. This article provides a detailed account of electromagnetic and thermal aspects of metallurgy of induction hardening of steels. It describes induction hardening techniques, namely, scan hardening, progressive hardening, single-shot hardening, and static hardening. The article discusses the techniques used to control the heat pattern, and provides a brief review of quenching techniques used in the induction hardening. It provides guidelines for selecting the frequency and power for induction hardening, and describes common methods for measuring case depth, such as optical and microhardness, and surface hardness. It provides information on some complications and ambiguities associated with these measurements. The article also discusses the commonly used non-destructive testing methods, namely, magnetic particle testing, ultrasonic testing, and eddy current testing to evaluate induction-hardened components.

Probability of detection (POD) assesses the performance of a non-destructive evaluation (NDE)-based inspection, which is a method used to determine the capability of an inspection as a function of defect type and defect size. This article provides an overview of the concept of POD, why it is needed, the history behind the development of POD, how POD assessments are performed, and how modeling and simulation can be integrated into the execution of a POD assessment. It describes the methods by which POD is determined. This includes detail on the experimental process to acquire the needed data, the mathematical methods to obtain a POD curve, and techniques to assess uncertainty in the POD curve as it is obtained from a limited data set. The concept of model-assisted POD (MAPOD) is introduced, with additional details and representative examples of MAPOD.

This article covers defect formation and classification, followed by a brief description of the most common nondestructive testing (NDT) methods used for postbuild inspection. Descriptions of the established and emerging NDT techniques for in-process monitoring (IPM) and in-process inspection (IPI) in additive manufacturing (AM) also are provided, highlighting the advantages and limitations. The article concludes with a list of the main NDT methods and techniques used. As qualification and certification of AM parts is an urgent matter for the AM industry, a description of the current work carried out for developing standards is also included.

This article is a brief guide to information sources on nondestructive testing (NDT). It provides examples of some of the standards bodies commonly used by NDT personnel. These include the American Society for Testing and Materials (ASTM) International, European Committee for Standardization (CEN), American Society of Mechanical Engineers (ASME), International Organization for Standardization (ISO), Aerospace Industries Association (AIA), American Welding Society (AWS), American Petroleum Institute (API), and American Society for Nondestructive Testing (ASNT). All of these organizations used industry subject-matter experts and a consensus process in the development of their codes and standards.

The goal of using nondestructive evaluation (NDE) in conjunction with failure analysis is to obtain the most comprehensive set of data in order to characterize the details of the damage and determine the factors that allowed the damage to occur. The NDE results can be used to determine optimal areas upon which to focus for sectioning and metallography in order to further investigate the condition of the component. This article provides information on the inspection method available for failure analysis, including standard methods such as visual testing, penetrant testing, and magnetic particle testing. It covers the effects of various factors on the properties of the part that may impact failure analysis, describes the characterization of damage modes and crack sizes, and finally discusses the processes involved in application of NDE results to failure analysis.

This article focuses on ultrasonic testing (UT) applied to metallic additive manufacturing (AM) parts, presenting the basic principles of UT. It provides a detailed discussion on postprocess UT inspection of powder-bed-fusion-manufactured samples and directed-energy-deposition-manufactured samples.

Microwave and guided wave (GW) nondestructive evaluation (NDE) techniques are capable of detecting corrosion damage, cracks, and other defect types in inaccessible areas. This article describes the operation principles of the techniques and provides information on hidden corrosion detection and the applications of microwave NDE devices and GW ultrasonic NDE devices.

X-ray radiography and computed tomography (CT) are nondestructive testing (NDT) tools particularly well suited to additive manufacturing (AM). A brief overview of NDT for AM is presented in this article, including other NDT methods, followed by identifying the key advantages and requirements for x-ray radiography and CT in AM. Less widely known applications of CT are also presented, including powder characterization, the evaluation of lattice structures, surface roughness measurements, and four-dimensional CT involving interrupted (before-after) CT scans of the same parts, or even in situ scans of the same part subjected to some processing or loading conditions. The article concludes with a discussion on the limits and some guidelines for the use of x-ray and CT for various AM materials.

Adhesive-bonded joints are extensively used in aircraft components and assemblies where structural integrity is critical. This article addresses the problem of how to inspect bonded assemblies so that all discrepancies are identified. It describes several inspection techniques and presents drawbacks and limitations of these techniques. Generic flaw types and flaw-producing mechanisms are listed in a table. The article discusses metal-to-metal defects, adherend defects, honeycomb sandwich defects, repair defects, and in-service defects. It reviews the methods applicable to the inspection of bonded structures, including visual inspection, ultrasonic inspection, X-ray radiography, and neutron radiography. The evaluation and correlation of inspection results are also discussed. The article concludes with information on the effects of ultrasonic wave interference in the ultrasonic inspection of adhesive-bonded joints.

This article presents the basic principle, characteristics, advantages, and disadvantages of resonant ultrasound spectroscopy (RUS) methods in additive manufacturing. It focuses on the two types of RUS methods: the swept-sine method and the impulse excitation method. Representative significant results for additively manufactured complex parts obtained with the different RUS systems are also shown. The article also presents the basic principle and examples of nonlinear RUS methods.

This article focuses on the aspects associated with inspection related to pressure vessels and pipework. These aspects include inspection policy, inspection planning and procedures, inspection strategy, inspection methodology, preparation for inspection, invasive inspection, internal visual inspection, and non-invasive inspection. Inspection execution, risk-based inspection, competence assurance of inspection personnel, inspection coverage, inspection periodicity, inspection anomaly criteria, assessment of fitness, and reporting requirements, are also discussed. The article addresses the data acquisition, reporting and trending, and review and audit for the inspection. It reviews inspection techniques, including visual inspection, ultrasonic inspection, and radiographic inspection.

Visual inspection (VI) is the oldest inspection technique man has used as a quality-control tool to evaluate products, assess their final form in terms of fabrication accuracy and external features based on experience, and decide on their acceptance or rejection. This article discusses the basic principles of visual inspection in terms of direct visual examination and indirect visual examination as well as advantages and limitations of visual inspection. It reviews the factors affecting the effectiveness of VI as a nondestructive testing (NDT): lighting conditions of observation, condition of surface under inspection, physical state/condition of inspector, proper training of personnel and level of expertise, and knowledge of applicable standards. The article provides schematic illustrations of rigid borescopes, fiberscopes, and videoscopes. It concludes with a discussion on automated optical inspection systems.

Before the quality of a soldered joint can be evaluated, the components that are required for the formation of a good soldered joint should be reviewed. These components are solder, applied heat, and solderable surface. This article discusses each of these as well as the end-use requirements and joint configurations required for the formation of a good soldered joint. It focuses on the visual, automatic, and destructive inspection techniques for determining overall joint quality.

Cold pressure welding can be accomplished by deforming in a lap or butt configuration, drawing, extrusion, and rolling. This article provides a discussion on cold pressure lap welding, cold pressure butt welding and cold pressure welding in drawing process with illustrations. It provides information on the combinations of metals that can be successfully cold welded.

Thermal spray coatings are often modified or treated by a variety of post-coating operations to transform the as-coated material into a final product based on coating composition and application. This article provides a detailed description of the post-coating operations that fall under two basic categories: surface treatments, such as dimensional, non-dimensional, and geometric finishing; and internal treatments, such as sealing, heat treating, and peening. It also describes various inspection and testing methods, including destructive and non-destructive inspections, often employed after post-coating operations.

Of the many different nondestructive evaluation (NDE) techniques, ultrasonic inspection continues to be the leading nondestructive method for inspecting composite materials, because measurements can be quantitative and the typical defect geometries and orientations lend themselves to detection and characterization. This article focuses on the three common methods for ultrasonic nondestructive inspection of plastics, namely pitch-catch, through-transmission, and pulse-echo, as well as the three basic types of ultrasonic NDE scans: the A-scan, B-scan, and C-scan. The discussion includes the linear and phased array systems that are sometimes used for large-scale inspection tasks to reduce scan times, the various gating and image processing techniques, and how ultrasonic data are interpreted and presented. A brief section on future trends in ultrasonic inspection is presented at the end of the article.

This article provides an overview of the characteristics of Rayleigh waves plus methods for generation and detection of waves, including using piezoelectric transducers or noncontact techniques such as lasers, electromagnetic acoustic transducers, or air-coupled ultrasonics. It reviews the methods for using Rayleigh waves for defect detection and materials characterization, alongside nonlinear ultrasonic inspection and surface acoustic wave (SAW) microscopy. The article concludes with information on the standards that use Rayleigh waves for nondestructive evaluation (NDE) of different structures.