Chemical vapor deposition (CVD) involves the formation of a coating by the reaction of the coating substance with the substrate. Serving as an introduction to CVD, the article provides information on metals, ceramics, and diamond films formed by the CVD process. It further discusses the characteristics of different pack cementation processes, including aluminizing, siliconizing, chromizing, boronizing, and multicomponent coating.

Polymeric floor coatings refer to flooring materials composed of multicomponent thermoset resins formulated with various fillers and pigments that are installed in situ, usually over concrete substrates. Polymeric flooring systems, specified for all industrial and commercial environments, use a variety of polymer chemistries and are constructed in a variety of methods and designs. This article provides a description of the service conditions for the polymeric flooring systems. It provides information on polymeric flooring systems, including thin-film coatings, self-leveling systems, membrane systems, broadcast systems, troweled systems, and terrazzo. The article also focuses on properties, applications, testing, and factors and requirements to be considered during the installation of polymeric floor coatings. It concludes with a discussion about coating failures, including bonding, cracking, chemical attack, and moisture that affect the polymeric floor coatings on concrete.

This article describes the methods used for coloring anodized aluminum coatings: integral coloring, electrolytic coloring, chemical coloring, and organic dyeing. It discusses organic dye chemistry in terms of single-component organic dyes and multicomponent dyes. The article reviews optimal dyeing conditions, such as temperature, time, concentration, and pH. It concludes with a discussion on the factors considered for choosing a coloring method: the desired shade, light fastness, heat fastness, and contamination.

This article focuses on the modeling and simulation of diffusion-controlled processes related to both materials processing such as heat treatments, and materials degradation from a practical perspective by using the one-dimensional (1-D) sharp interface approach. It describes various diffusion simulation models, such as one-phase simulations, moving phase-boundary simulations, and dispersed system simulations. The article presents case studies that illustrate some examples where diffusion simulations have been applied to industrial-based problems, with an emphasis on the approaches used and the lessons learned from performing such simulations.

This article presents various equations that are essential for the modeling of both single-phase and multiphase profiles. It includes the fundamental laws of diffusion, along with its equations and solutions. The article provides information on the series of applications that illustrate how various diffusional processes can be modeled.

Pack cementation is the most widely employed method of diffusion coating. This article briefly reviews pack cementation processes of aluminizing, chromizing, and siliconizing. It contains tables that list typical characteristics of pack cementation processes and commercial applications of pack cementation aluminizing, which is used to improve the performance of steels in high-temperature corrosive environments.

This article presents a general description of pulsed-laser deposition. It describes the components of pulsed-laser deposition equipment. The article also discusses the effects of angular distribution of materials. Finally, the article reviews the characteristics of high-temperature superconductors and ferroelectric materials.

The process of transferring coating materials from the container to the surface to be coated can be accomplished in a number of ways. This article describes seven methods of coating application: brushes, rollers, and daubers; conventional air spray; high-volume low-pressure spray; airless spray; air-assisted airless spray; plural-component spray; and electrostatic spray. Factors to be considered when deciding on an application method include the size and configuration of the surfaces to be coated, the type of coating being applied, environmental regulations/restrictions, the proximity to other operations or personnel, and the recommendations of the coating manufacturer.

A major effort in the development of thermal spray applications has been the improvement of process reliability and predictability in response to process changes. The ability to model a process is a prerequisite to understanding and controlling it. This article provides an overview of thermal spray process modeling, as it applies to the engineering of new thermal spray equipment and coating development.

Diffusion is the process by which molecules, atoms, ions, point defects, or other particle types migrate from a region of higher concentration to one of lower concentration. This article focuses on the diffusivity data and modeling of lattice diffusion in solid-state materials, presenting their diffusion equations. It discusses different methods for evaluating the diffusivity of a material, including the measurement of diffusion coefficients, composition profiles, and layer growth widths. The article reviews the various types of direct and indirect diffusion experiments to extract tracer, intrinsic, and chemical diffusivities. It provides information on the applications of single-phase and multiphase diffusion.

Solid lubricants consist of materials placed at the interface between moving bodies to mitigate friction and wear. This article begins with a historical overview of solid lubricants and discuses the characteristics and fundamental aspects of solid lubricants. It describes the material categories of solid lubricant coatings, including graphite, graphite fluoride, transition metal dichalcogenides, diamond-like-carbon, polymeric materials, and metallic films. The article presents a description of deposition methods from the simplest processes involving burnishing and impingement in open air to modern vacuum-based methods for solid lubricants. It concludes with a discussion on metrics that can be used to qualify solid lubricants in high-consequence applications.

Sputtering is a nonthermal vaporization process in which the surface atoms are physically ejected from a surface by momentum transfer from an energetic bombarding species of atomic/molecular size. It uses a glow discharge or an ion beam to generate a flux of ions incident on the target surface. This article provides an overview of the advantages and limitations of sputter deposition. It focuses on the most common sputtering techniques, namely, diode sputtering, radio-frequency sputtering, triode sputtering, magnetron sputtering, and unbalanced magnetron sputtering. The article discusses the fundamentals of plasma formation and the interactions on the target surface. A comparison of reactive and nonreactive sputtering is also provided. The article concludes with a discussion on the several methods of process control and the applications of sputtered films.

This article reviews the various substrates for coatings, namely, steel, cast iron, galvanized steel, aluminum, stainless steel, nonferrous metals, concrete, and wood. General guidance for surface preparation and coating selection is provided along with unique requirements for the particular substrate(s).

Boriding is a thermochemical diffusion-based surface-hardening process that can be applied to a wide variety of ferrous, nonferrous, and cermet materials. It is performed on metal components as a solution for extending the life of metal parts that wear out too quickly in applications involving severe wear. This article presents a variety of methods and media used for boriding of ferrous materials, and explains their advantages, limitations, and applications. These methods include pack cementation boriding, gas boriding, plasma boriding, electroless salt bath boriding, electrolytic salt bath boriding, and fluidized-bed boriding. The article briefly describes the chemical vapor deposition process, which has emerged to be dominant among metal-boride deposition processes.

A phase diagram is a graphical representation of the phase equilibria of materials in terms of temperature, composition, and pressure. This article provides an overview on the background of phase diagram calculation software. It presents an algorithm to calculate binary stable phase equilibria. The article summarizes a rapid method to obtain a thermodynamic description of a multicomponent system. It also provides information on thermodynamically calculated phase diagrams.

This article discusses the concepts of quality control (QC) and quality assurance (QA), and clarifies the differences and similarities in the roles and responsibilities of QC and QA personnel. It describes the inspection procedures used to verify proper surface preparation and installation of the protective coating/lining system. Prior to beginning surface-preparation operations, many specifications will require a presurface-preparation inspection to verify the correction of fabrication defects and removal of surface contamination such as grease, oil, cutting compounds, lubricants, and chemical contaminants. When inspecting concrete prior to coating installation, three areas of concern exist: surface roughness, moisture content in concrete, and acidity/alkalinity of the surface. The article provides information on the industry standards for assessing surface cleanliness. It details postcoating application quality requirements, including measuring of dry-film thickness, assessing intercoat cleanliness, verifying minimum and maximum recoat intervals, performing holiday/pinhole detection, conducting cure/hardness testing, and assessing adhesion of the applied coating system.

This article provides an overview of the electrochemical nature of corrosion and analyzes corrosion-related failures. It describes corrosion failure analysis and discusses corrective and preventive approaches to mitigate corrosion-related failures of metals. These include: change in the environment; change in the alloy or heat treatment; change in design; use of galvanic protection; use of inhibitors; use of nonmetallic coatings and liners; application of metallic coatings; use of surface treatments, thermal spray, or other surface modifications; corrosion monitoring; and preventive maintenance.

This article addresses two issues on thermodynamics, namely, the calculation of solubility lines and the calculation of the activity of various components. It discusses alloying elements in terms of their influence on the activity of carbon. The article describes the desulfurization and deoxidation of cast iron and steel. It illustrates the thermodynamics of the iron-carbon system and the iron-silicon system. The article examines solubility and saturation degrees of carbon in multicomponent iron-carbon systems. One of the main applications of the thermodynamics of the iron-carbon system is the calculation of structure-composition correlations. The article concludes with information on the structural diagrams for cast iron: the Maurer diagram and the Laplanche diagram.

Surface treatments are used in a variety of ways to improve the material properties of a component. This article provides information on surface treatments that improve service performance so that the design engineer may consider surface-engineered components as an alternative to more costly materials. It describes solidification surface treatments such as hot dip coatings, weld overlays, and thermal spray coatings. The article discusses deposition surface treatments such as electrochemical plating, chemical vapor deposition, and physical vapor deposition processes. It explains surface hardening and diffusion coatings such as carburizing, nitriding, and carbonitriding. The article also tabulates typical characteristics of carburizing, nitriding, and carbonitriding diffusion treatments.

This article discusses three types of powder-feeder systems that are commonly used throughout the thermal spray (TS) industry: gravity-based devices, rotating wheel devices, and fluidized-bed systems. It provides information on the various mechanical methods for producing powders, namely, crushing, milling, attriting, and machining. The article describes two prime methods of agglomeration. One method uses a binder by way of agglutination, while the other relies on a sintering operation. The article discusses the technology and principles of the processes that relate to thermal spraying, and offers an understanding for choosing particular feedstock materials that are classified based on the thermal spray process, material morphology, chemical nature of the material, and applications. Sieving, the most common method of separating powders into their size fractions, is also reviewed. The article also provides information on the topical areas and precautions to be undertaken to protect the operator from safety hazards.