1-20 of 106 Search Results for

multiaxial fatigue strength

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002366
EISBN: 978-1-62708-193-1
... and ductile structural alloys. crystallographic growth cycle counting grain size high-cycle fatigue low-cycle fatigue multiaxial fatigue strength normal stress-dominated growth small fatigue cracks strain amplitude MOST ENGINEERING DESIGNS and/or failure analyses involve three...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003320
EISBN: 978-1-62708-176-4
... section provides a brief review of these stress states. Additional information is provided in the article “Multiaxial Fatigue Strength” in Fatigue and Fracture , Volume 19 of Asm Handbook . Since no standard testing method exists, it is important to...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003269
EISBN: 978-1-62708-176-4
... biaxial loads. Test specimen geometries and testing equipment configurations can be adapted to multiaxial testing for static strength, fatigue, and creep. Some sections and paragraphs from Ref 12 are included in this article without alteration. The use of this previously published...
Series: ASM Handbook
Volume: 20
Publisher: ASM International
Published: 01 January 1997
DOI: 10.31399/asm.hb.v20.a0002469
EISBN: 978-1-62708-194-8
... concentration, and multiaxial fatigue. It describes low-cycle fatigue in terms of deformation behavior and concludes with a discussion on lifetime analysis based on a strain approach. crack propagation deformation fatigue failure fatigue resistance fatigue strength high-cycle fatigue low-cycle...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003314
EISBN: 978-1-62708-176-4
... influence of the plasticity. As an example, high-ductility, low-strength metals such as copper behave in a low-cycle fatigue manner even at 10 6 cycles to failure, because the cyclic strain range may be half plastic and half elastic even at this life level. By contrast, a low-ductility, high-strength...
Book Chapter

Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003544
EISBN: 978-1-62708-180-1
... effects of load frequency and temperature, material condition, and manufacturing practices on fatigue strength. It provides information on subsurface discontinuities, including gas porosity, inclusions, and internal bursts as well as on corrosion fatigue testing to measure rates of fatigue-crack...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0009219
EISBN: 978-1-62708-176-4
... discussed. The techniques for defining a mean fatigue curve and evaluating scatter or variability about that mean are explained. The article presents the standard techniques for statistical characterization of the fatigue strength or fatigue limit of a single material by use of the Probit method, the up-and...
Series: ASM Handbook
Volume: 6A
Publisher: ASM International
Published: 31 October 2011
DOI: 10.31399/asm.hb.v06a.a0005556
EISBN: 978-1-62708-174-0
... – 57 51. Kharchenko G.K. and Ignatenko A.I. , The Strength of Joints with a Thin Soft Interlayer , Auto. Weld. , Vol 21 , 1968 , p 33 – 35 52. Leher W.M. and Schwartzbart H. , Static and Fatigue Strength of Metals Subjected to Triaxial Stresses , Vol 60...
Series: ASM Handbook
Volume: 22A
Publisher: ASM International
Published: 01 December 2009
DOI: 10.31399/asm.hb.v22a.a0005405
EISBN: 978-1-62708-196-2
.... and Ellis R. , eds., ASTM STP 1191, ASTM , Philadelphia , 1993 , p. 7 – 36 9. McDowell D.L. , Multiaxial Fatigue Strength , ASM Handbook , Vol 19 on Fatigue and Fracture, ASM International , 1996 , p. 263 – 273 10. McDowell D.L. , Gall K. , Horstemeyer...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002350
EISBN: 978-1-62708-193-1
... “Multiaxial Fatigue Strength” in this Volume. Application of the strain-life method in its simplest form is to compare the total strain amplitude (Δε/2) at a detail of the part to a ε- N curve having the necessary mean strain (stress) effects included. The assumption here is that the detail on the part...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006549
EISBN: 978-1-62708-210-5
... situations where creep and fatigue are active simultaneously. Multiaxial loads as well as in- and out-of-phase loading should be reviewed carefully for possible interactions, and situation-specific testing may be required (e.g., see the article “Multiaxial Fatigue Strength” in Fatigue and Fracture , Volume...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006779
EISBN: 978-1-62708-295-2
...) N = N R · ( S a R / S a ) k where k is the slope of the finite-life line. The slope k is typically characterized by values between 3 and 15. A low slope corresponds with a low relationship between the fatigue strength, S AF , and the static strength, S u...
Series: ASM Handbook
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003382
EISBN: 978-1-62708-195-5
.... Such a failure can occur at a small fraction of the static strength of a material. In this sense, fatigue in composite materials is observed through accumulation of damage that initiates and progresses during cyclic loading and exposure to environment. The cyclic loading causes damage, reducing the...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002399
EISBN: 978-1-62708-193-1
... formed during tempering of white cast iron. These categories of graphite shape have a strong influence on fatigue and fracture properties, although microstructure (tensile strength), component/specimen size, surface condition, chemistry, and temperature also affect the general fatigue and fracture...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002364
EISBN: 978-1-62708-193-1
... Metallurgy , McGraw-Hill , 1961 5. Morrow J. , Halford G.R. , and Millan J.F. , Optimum Hardness for Maximum Fatigue Strength of Steels , Proceedings of the First International Conference on Fracture , ( Sendai, Japan ), Vol 3 , 1965 , p 1611 – 1635 6. Landgraf R.W...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002351
EISBN: 978-1-62708-193-1
... classes of materials. More detailed information on fracture mechanisms is given in the article “Micromechanisms of Monotonic and Cyclic Crack Growth” in this Volume. In general, fracture toughness can be viewed as a property that depends on both strength and ductility, modified by the complex stress...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002365
EISBN: 978-1-62708-193-1
... reflects statistical effects that cause lower fatigue strengths to be observed in larger size members. For example, Juvinall recommends m d = 1 for diameters less than 10 mm, m d = 0.9 for diameters 10 to 50 mm, m d = 0.8 for diameters 50 to 100 mm, and so forth. Surface finishes other than a fine...
Series: ASM Handbook
Volume: 13A
Publisher: ASM International
Published: 01 January 2003
DOI: 10.31399/asm.hb.v13a.a0003668
EISBN: 978-1-62708-182-5
.... , Application of Ultrasonic Fatigue Testing Techniques to the Evaluation of the Corrosion-Fatigue Strength of Materials , Environment-Sensitive Fracture , STP 821, Dean S.W. , Pugh E.N. , and Ugianski G.M. , Ed., American Society for Testing and Materials , 1984 , p 497 – 512 44...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002357
EISBN: 978-1-62708-193-1
... crack lengths, the plain fatigue strength is plotted as an upper limit to the stress amplitude, an indication that Frost realized that there was a transition from crack length control of the fatigue limit to material control in the very short crack length region. Further mention of this transition is...
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002391
EISBN: 978-1-62708-193-1
... under Isothermal and Thermal Cycling Conditions , Fracture 77: Advances in Research on the Strength and Fracture of Materials , Taplin D.M.R. , Ed., Pergamon Press , 1978 , p 755 – 765 28. Sheffler K.D. , Vacuum Thermal-Mechanical Fatigue Testing of Two Iron Base High Temperature...