1-20 of 655 Search Results for

melt fluxing

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005285
EISBN: 978-1-62708-187-0
... implications of dross, and in-plant enhancement or recovery of dross. It discusses the influence of the melter type on dross generation and the influence of charge materials and operating practices on melt loss. Fluxing is a word applied in a broad sense to a number of melt-treating methods. The article also...
Series: ASM Handbook
Volume: 4C
Publisher: ASM International
Published: 09 June 2014
DOI: 10.31399/asm.hb.v04c.a0005846
EISBN: 978-1-62708-167-2
..., and linear coils. It provides information on the role of magnetic flux controllers for whole-body and local area mass-heating applications, continuous induction tube welding, seam-annealing inductors, and various induction melting systems, namely, channel-type, crucible-type, and cold crucible systems...
Image
Published: 09 June 2014
Fig. 70 Severe copper melting occurred in an area where a flux concentrator was positioned. More
Image
Published: 09 June 2014
Fig. 23 Magnetic flux density, frequency, and furnace filling over a melting period in a 9.5 MW crucible furnace. Source: Ref 13 More
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005300
EISBN: 978-1-62708-187-0
... Abstract Aluminum fluxing is a step in obtaining clean molten metal by preventing excessive oxide formation, removing nonmetallic inclusions from the melt, and preventing and/or removing oxide buildup on furnace walls. This article discusses the solid fluxes and gas fluxes used in foundries...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006535
EISBN: 978-1-62708-207-5
... Abstract There are a wide variety of furnace types and designs for melting aluminum. This article discusses the various types of furnaces, including gas reverberatory furnaces, crucible furnaces, and induction melting furnaces. It describes the classification of solid fluxes: cover fluxes...
Book Chapter

Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005307
EISBN: 978-1-62708-187-0
... Abstract This article describes the control of alloy composition and impurity levels in die casting of zinc alloys based on agitation, use of foundry scrap, and melt temperature and fluxing. It reviews the process considerations for the melt processing of the zinc alloys. The process...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005352
EISBN: 978-1-62708-187-0
... Of primary importance during melting and the handling of molten metal is the mitigation and reduction of dissolved gases and inclusions in the melt. This objective may be accomplished in different ways, depending on the base metal, alloying constituents, and residual impurities. Fluxing Fluxing...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005303
EISBN: 978-1-62708-187-0
... Abstract This article describes the casting characteristics and practices of copper and copper alloys. It discusses the melting and melt control of copper alloys, including various melt treatments to improve melt quality. These treatments include fluxing and metal refining, degassing...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006529
EISBN: 978-1-62708-207-5
... of the 5 xxx series. Alloys containing higher magnesium content, such as 5083, 5086, 5154, and 5456, are more difficult to braze by means of the usual flux methods because of poor wetting and excessive capillary penetration by the filler metal. Filler metals are available that melt at temperatures below...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001344
EISBN: 978-1-62708-173-3
... Filler metal melt temperature, °C (°F) <450 (<840) >450 (>840) (a) >450 (>840) (b) Base metal Does not melt Does not meltFluxes used to protect and to assist in wetting of base-metal surfaces Required Optional Optional Typical heat sources Soldering iron...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003211
EISBN: 978-1-62708-199-3
.... fluxing precleaning solder alloys soldered joints soldering surface preparation SOLDERING involves heating a joint to a suitable temperature and using a filler metal (solder) that melts below 450 °C (840 °F). The solder is distributed between the closely fitted surfaces of the joint by capillary...
Book Chapter

By David V. Neff
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005353
EISBN: 978-1-62708-187-0
... humidity conditions exacerbate not only hydrogen dissolution in the melt but also can retard the ability of any melt treatment to remove hydrogen, because a degassed melt can then readily redissolve additional hydrogen. Ingot, additives, and fluxes are other common sources of hydrogen. In the case...
Book Chapter

By