Search Results for material control

In-process inspection during composite material lay-up is essential if the structural, dimensional, and environmental performance designed into a part is to be consistently achieved. This article discusses the requirements to be met by the facilities and equipment to produce high-quality composites. It reviews the procedures that are allowed and prohibited in controlled-contamination areas of lay-up. The article emphasizes significant areas, such as material control and lay-up process, in which quality-control personnel can be effective in preventing production problems. It concludes with a discussion on automated tape laying and fiber placement, as well as the numerically aided lay-up process.

This article outlines the processes by which materials are selected to prevent or control localized corrosion, galvanic corrosion, and intergranular corrosion. It reviews the operating conditions and the design of candidate materials for material selection. The article discusses various corrosion-resistant materials, including ferrous and nonferrous metals and alloys, thermoplastics, reinforced thermosetting plastics, nonmetallic linings, glass, carbon and graphite, and catalyzed resin coatings. It examines an unusual form of intergranular corrosion known as exfoliation, which occurs in aluminum-copper alloys. The article also describes three types of erosion-corrosion: liquid erosion-corrosion, cavitation, and fretting. It concludes with information on the various factors to be considered for material selection, including minimum cost or economic design, minimum corrosion, minimum investment, and minimum maintenance.

Ultrasonic inspection is a nondestructive technique that is useful in both quality control and research applications for flaw detection in fiber-reinforced composite materials. This article describes ultrasonic nondestructive analysis by outlining its three basic types of scans. It reviews the important quality control techniques used during the manufacture of composite components by analyzing tooling control, material control, pattern orientation control, and in-process control.

Forgings are classified in various ways, beginning with the general classifications open die and closed die. They are also classified according to how they are made; such as hammer upset forgings, ring-rolled forgings, and multiple-ram press forgings; and in terms of the close-to-finish factor or amount of stock that must be removed to satisfy the dimensional and detail requirements of the finished part. In addition to types and classifications, the article discusses critical design factors and ways to ensure that the resulting forgings measure up to metallurgical, mechanical property, and dimensional accuracy requirements. The responsibility for design verification is vested in material control, which depends on the proper application of drawings, specifications, manufacturing process controls, and quality assurance programs. The article addresses each of these areas as well as related topics; including stress-induced fatigue failure, tolerances, machining allowances; and the fundamentals of hammer and press forgings, hot upset forgings, and hot extrusion forgings.

Curing is the irreversible change in the physical properties of a thermosetting resin brought about by a chemical reaction, condensation, ring closure, or addition. This article discusses the material types and functions of various components considered in the preparation for curing. It presents a discussion on the major elements of an autoclave system, namely, pressure vessel, gas stream heating and circulation sources, gas stream pressurizing systems, loading systems, and vacuum systems. The article describes a computerized approach to the simultaneous control of materials reaction behavior and consolidation dynamics, using an autoclave as the reaction vessel.

This article is a detailed account of the advantages, disadvantages, and applications of microdispensing processes used in electronics manufacturing industries. The discussion covers various approaches to control material flow, namely time pressure, auger, positive displacement, and progressive cavity pump dispensing. The concept of valving to control starting and stopping is also discussed. The applications include printing solders in microelectronic packaging, printing to pads, printing conductive patterns for antennas, printing active circuits, printing on flexible surfaces, and structural printing.

Forging is the process of working hot metal between dies, usually under successive blows and sometimes by continuous squeezing. This article describes the material selection criteria, quality assurance tests for forged components, and the dimensional tolerances of closed-die steel forgings. It provides an overview of the mechanical properties of wrought materials. The article also includes information on the fundamentals of hammer and press forgings and the design of hot upset forgings.

This article presents the history of standardization in additive manufacturing (AM). It explains the need and structure for standardization in AM, including the application of AM standards by the industry sector. It also presents the primary purposes of these standards to create AM qualification and certification frameworks.

Unexpected and frequently costly failures occur due to the lack of sound and reliable engineering design. Therefore, designing against corrosion is essential for reducing such failures. This article provides a discussion on design considerations and general corrosion awareness. It details the functional requirements, such as design and materials selection, which assist in controlling corrosion in different environments. The article also illustrates the design factors that accelerate corrosion.

This article discusses the particular corrosion problems encountered and the corrosion control methods used in petroleum production (i.e., upstream) and the storage and transportation of oil and gas (i.e., midstream) up to the refinery (i.e., downstream). These control methods include proper material selection, protective coatings, cathodic protection systems, use of inhibitors, use of nonmetallic materials, and control of the environment. The article reviews the aspects of corrosion that tend to be unique to corrosion as encountered in applications involving oil and gas exploration and production. It discusses corrosion problems that are specific to the various types of environments or equipment used in secondary recovery, including producing wells, producing flow lines, and injection wells. Corrosion mitigation methods and guidelines are also discussed for each type of environment.

Unlike gray iron, which contains graphite flakes, ductile iron has an as-cast structure containing graphite particles in the form of small, rounded, spheroidal nodules in a ductile metallic matrix. This article discusses the raw materials that are used for ductile iron production and outlines the most common and important requirements for controlling the composition of ductile iron. Treatment to produce ductile iron involves the addition of magnesium to change the form of the graphite, followed by or combined with inoculation of a silicon-containing material to ensure a graphitic structure with freedom from carbides. The article describes the methods of magnesium treatment, control of magnesium content, and inoculation. It concludes with a discussion on the metallurgical controls of ductile iron production.

Magnetic flux controllers are materials other than the copper coil that are used in induction systems to alter the flow of the magnetic field. This article describes the effects of magnetic flux controllers on common coil styles, namely, outer diameter coils, inner diameter coils, and linear coils. It provides information on the role of magnetic flux controllers for whole-body and local area mass-heating applications, continuous induction tube welding, seam-annealing inductors, and various induction melting systems, namely, channel-type, crucible-type, and cold crucible systems. The article also describes the benefits of the flux controllers for induction heat treating processes such as single-shot and scanning.

This article describes the control of water chemistry in the steam cycle of a power plant for achieving corrosion control, deposition prevention, and higher cycle efficiency. It discusses the materials requirements of the components exposed to supercritical water in supercritical (SC) and ultrasupercritical (USC) power plants. These components include high-pressure steam piping and headers, superheater and reheater tubing, water wall tubing in the boiler, high-and intermediate-pressure rotors, rotating blades, and bolts in the turbine section. The article reviews the boiler alloys, used in SC and USC boilers, such as ferritic steels, austenitic steels, and nickel-base alloys. It provides information on the materials used in turbine applications such as ferritic rotor steels, turbine blade alloys, and bolting materials. The article explains various factors influencing steamside corrosion in SC power plants. It also deals with the role of overall efficiency in the USC power generation.

Blow molding has emerged as a commercially viable process for manufacturing parts for nonpackaging/industrial markets. This article discusses the machinery required, processing methods, mold types, process parameters, part designs and material distribution of blow molding. It provides an outline of the parison programming system equipped with blow molders to control the parison thickness. The article describes factors that are usually considered to minimize material distribution problems, namely, design, material selection, process control, part performance, and cost.

Fundamental to the machining process, is the metal-cutting operation, which involves extensive plastic deformation of the work piece ahead of the tool tip, high temperatures, and severe frictional conditions at the interfaces of the tool, chip, and work piece. This article explains that the basic mechanism of chip formation is shear deformation, which is controlled by work material properties such as yield strength, shear strength, friction behavior, hardness, and ductility. It describes various chip types, as well as the cutting parameters that influence chip formation. It also demonstrates how the service life of cutting tools is determined by a number of wear processes, including tool wear, machining parameters, and tool force and power requirements. It concludes by presenting a comprehensive collection of formulas for turning, milling, drilling, and broaching, and its average unit power requirement.

This article presents a discussion on the U.S army's position on corrosion control for wheeled tactical vehicles. It addresses the army requirement for corrosion control. The U.S. Army Tank-automotive and Armaments Command (TACOM) defines the corrosion prevention and control requirements in the procurement document. The article summarizes requirements from a procurement document. As required by the procurement contract, corrosion-control technologies used in a vehicle system need to be evaluated to determine their benefit. The article provides information on testing systems, which help to meet the army's needs. It includes information on supplemental corrosion protection, which improves the corrosion resistance of a material.

A wide range of flow-formed open- and close-ended shapes are currently available in a variety of difficult-to-form materials, including titanium alloys and nickel-base super alloys. This article describes the two basic methods of flow forming that are characterized by the position of the rolls during the forming process. The flow forming methods include staggered-roll flow forming process and in-line flow-forming process. Typical mechanical properties of flow-formed materials in various conditions are summarized in a table. Proper process controls and subsequent product qualification tests are critical to assure optimal performance of the flow-formed tubular component. The article discusses the most commonly required process control parameters and the effects of forming speed and temperature in the flow forming process.