1-11 of 11 Search Results for

macropitting

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002401
EISBN: 978-1-62708-193-1
... Table 2 List of contact fatigue terminology used to describe the different fatigue mechanisms Macroscale Microscale Macropitting Pitting Initial Pitting Destructive Pitting Flaking Spalling Scabbing Shelling Fatigue wear Subcase Fatigue Case crushing...
Book Chapter

Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003544
EISBN: 978-1-62708-180-1
... propagation in different environments. The article concludes with a discussion on rolling-contact fatigue, macropitting, micropitting, and subcase fatigue. corrosion fatigue crack growth crack initiation damage tolerance criterion fatigue fracture fatigue strength fatigue-crack propagation finite...
Series: ASM Handbook
Volume: 18
Publisher: ASM International
Published: 31 December 2017
DOI: 10.31399/asm.hb.v18.a0006354
EISBN: 978-1-62708-192-4
... discharge), scuffing, and Hertzian fatigue (including macropitting and micropitting). Details for obtaining high lubricant specific film thickness are presented. The article describes the selection criteria for lubricants, such as oil, grease, adhesive open gear lubricant, and solid lubricants. It discusses...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006779
EISBN: 978-1-62708-295-2
Series: ASM Handbook
Volume: 19
Publisher: ASM International
Published: 01 January 1996
DOI: 10.31399/asm.hb.v19.a0002375
EISBN: 978-1-62708-193-1
... derating factor. Table 4 Situations and concepts of pitting failures in gears Description Recommended action Situation 1 Some micropitting and a few macropits on the pinion. No gear pitting. Scrap the pinion, even though it is still quite runnable. It may not last until the next...
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0003827
EISBN: 978-1-62708-183-2
... not be touched with bare hands. Clean white cotton, nylon, polyethylene, or rubber gloves are usually used. If anything else is touched with the gloves, a clean pair should be put on before touching the beryllium again. The most notorious cause of macropit formation in etched beryllium surfaces...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003327
EISBN: 978-1-62708-176-4
... in.) or deeper, depending on contact geometry, shear stresses produced by the contact loading become high enough to promote rapid crack propagation. Progressively larger pieces break away from the surface, leaving yet larger cavities. This condition is termed pitting or macropitting . The material is torn...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006765
EISBN: 978-1-62708-295-2
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003563
EISBN: 978-1-62708-180-1
... is, however, inevitable in both pure rolling and rolling/sliding conditions. The term “RCF” in this article, however, refers to pure rolling configurations, except where specific references to rolling/sliding conditions are made. The material removal in a RCF failure varies from micropitting, macropitting...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001816
EISBN: 978-1-62708-180-1
Series: ASM Handbook
Volume: 4B
Publisher: ASM International
Published: 30 September 2014
DOI: 10.31399/asm.hb.v04b.a0005967
EISBN: 978-1-62708-166-5