Wear is the damage to a solid surface as a result of relative motion between it and another surface or substance. This article discusses the four general ways by which a material can wear, namely, adhesive wear, abrasive wear, fatigue or fatigue-like wear, and corrosive wear. It tabulates the operational classification of wear situations and describes the relationship between wear or wear rate and design parameters. The article reviews the effect of lubrication on wear behavior and the types of lubricants. It illustrates some fundamental criteria that can be applied in the selection of a material for wear applications. The article explains four elements of wear design, such as system analysis, modeling, data gathering, and verification. It concludes with a discussion on the design approach for low-wear computer peripherals.

This article commences with a schematic illustration of a wide range of cutter configurations available for use in milling operations. It describes the various types of milling machines classified based on the type of construction, such as knee-and-column type, bed-type, planer-type, and special type. The article discusses mechanical-electric, mechanical-hydraulic, mechanical-electric-hydraulic, and numerical control of milling machines. It describes various types of milling cutters, such as peripheral mills, face mills, end mills, and special mills. Milling cutters, such as solid milling cutters, inserted-blade cutters, and indexable-insert cutters, are also discussed. The article explains the capabilities and limitations of peripheral milling, face milling, and end milling methods. It concludes with a comparison of milling with broaching, planing or shaping, and grinding.

Seals are mechanical components that prevent the leakage, diffusion, transfer, or mixing of different liquid, gas, solid, and multiphasic substances. This article begins by discussing the classifications of seals: static and dynamic. Static seals involve both self-energizing elastomeric materials such as O-rings, which merely react to a sealed fluid pressure, and passive materials that require clamping forces to achieve sealing, such as gaskets. The types of dynamic seals include rotary seals and reciprocating seals. The article describes the factors affecting seal wear and failure. It provides a list of some common seal wear modes and failures, namely abrasion, cavitation damage, chemical attack, compression set, corrosion, damage during abrupt decompression, dieseling damage, extrusion damage, installation damage, spiral or rolling damage, and vaporization damage. The article concludes with specific recommendations for reducting of seal friction and wear.

After solidification and cooling, further processing and finishing of the castings are required. This article describes the general operations of shakeout, grinding, cleaning, and inspection of castings, with particular emphasis on automation technology. It illustrates the vertical core knockout machine and the A-frame core knockout machine and lists the advantages and disadvantages of these machines. The article describes the general factors in automated or manual gate removal process. It concludes with discussion on the various types of inspection, such as the liquid penetrant inspection, pressure testing, radiographic inspection, magnetic particle inspection, and ultrasonic inspection.

This article focuses on the machining of reactive metals which refer collectively to the elements titanium, hafnium, and zirconium. It provides guidelines for machining titanium and titanium alloys and describes machining operations, such as turning, milling, drilling, tapping, reaming, grinding, and sawing, performed on titanium and its alloys. The article also provides information on electrochemical machining (ECM), chemical milling (CHM), and laser beam machining (LBM) for titanium and titanium alloys. Guidelines for machining zirconium alloys and hafnium are also provided. The article provides a short description of turning, milling, and drilling operations performed on zirconium alloys and hafnium. It also discusses health and safety considerations related to zirconium and hafnium.

Hot extrusion is a process in which wrought parts are formed by forcing a heated billet through a shaped die opening. This article discusses nonlubricated and lubricated hot extrusion. The two nonlubricated hot extrusion methods are forward or direct extrusion and backward or indirect extrusion. The article illustrates the significance of extrusion speeds and temperatures in hot extrusion. It describes the basic types of presses used in the hot extrusion of metals. The article provides information on the characterization of extruded shapes and explains the operating parameters, including extrusion velocity, amount of pressure required, and type of lubricant, for successful and efficient hot extrusion. The article concludes with a discussion on applications and design methodology that provides insight into CAD/CAM of extrusion dies.

Cutting tool wear is a production management problem for manufacturing industries. It occurs along the cutting edge and on adjacent surfaces. This article describes steady-state wear mechanisms, tertiary wear mechanisms, and tool replacement. It provides information on tool failure and its consequences. The article details the modeling of tool wear by using the Taylor's tool life equation. The article concludes with information on the requirements of a successful tool life testing program: the test plan objective, designing the test, conducting the test, analyzing the results, and applying the results.

Powder metallurgy compacting presses usually are mechanically or hydraulically driven, but they can incorporate a combination of mechanically, hydraulically, and pneumatically driven systems. This article provides a comparison of mechanical and hydraulic presses based on the cost, production rate, and machine overload protection. The article lists the classification of powder metallurgy parts based on complexity of shapes as suggested by the Metal Powder Industries Federation, such as Class I parts, Class II parts, Class III parts, and Class IV parts. It describes rigid tooling compaction and details the powder-fill ratio considerations for these classes. The article elaborates on the types of tooling systems and presses used for these classes. Some important factors and components used in designing a tool are also described. Finally, the article considers tool materials, including punches, core rods, and punch clamp rings.

This article describes the influence of steel chemical compositions and microstructure on machining processes. It discusses the various microstructural phases of standard carbon and alloy steels, which influence machinability. The article reviews the expected response of several traditional machining operations, such as turning, drilling, milling, shaping, thread cutting, and grinding, to the microstructure of standard steel grades. It also explains the technologies in non-traditional machining processes, such as abrasive waterjet cutting, electrical chemical grinding, and laser drilling.

This article provides an overview of electromagnetic fields (EMFs) and discusses their direct and indirect effects on human health. It provides a detailed description of the exposure levels of EMFs in residential and work environments. The article examines the international and European standards and regulations regarding occupational exposure to EMFs encountered in industrial activities. It discusses the categories of work equipment or activities that may expose the worker above and under the orientation value. The article also describes the main principles underlying the protection system adopted for the frequency range of 50 Hz to 10 MHz.

Erosion, cavitation, and impingement are mechanically assisted forms of material degradation that often contribute to corrosive wear. This article identifies and describes several tests that are useful for ranking the service potential of candidate materials under such conditions. The tests, designed by ASTM as G32, G73, G75, and G76, define specimen preparation, test conditions, procedures, and data interpretation. The article examines the relative influence of various test parameters on the incubation and intensity of cavitation, including temperature, pressure, flow velocity, and vibration dynamics. It concludes with a discussion on data correlations and the relationship between laboratory results and service expectations.

This article provides a detailed discussion on the components of a high-performance induction crucible furnace system, namely, furnace body, power supply, and peripheral components. The furnace body contains refractory lining, coil and transformer yokes, and tilting frame and furnace cover. The power supply consists of the following: transformers, frequency converters, capacitor banks, and power cables and furnace coils. The peripheral components comprise recooling device, charging system, and skimming devices. The article also presents a three-dimensional representation of the induction crucible furnace system.

This article focuses on different aspects of wear particle analysis. It discusses the different wear regimes in the wear rate versus time (bathtub) curve. The article explains the essence of condition monitoring and how to properly sample lubricants for condition monitoring. It also discusses in-service lubricant analysis for condition monitoring, focusing on the spectrometric oil analysis program. The article describes the characteristics of wear particles and analytical techniques for characterizing them. It also describes the characteristics of different types of wear particles and the mechanisms by which they are generated. The article concludes with a summary of the major applications of wear particle analysis.

Electrochemical machining (ECM) is the controlled removal of metal by anodic dissolution in an electrolytic cell in which the workpiece is the anode and the tool is the cathode. This article begins with a description of the ECM system and then discusses the primary variables that affect current density and the material removal rate in the ECM process. It reviews the various characteristics of electrolytes and considers tool material and design. It also provides an overview of the properties of the workpiece and defines the surface finish and accuracy of an electrochemically machined sample. The variety of work done by electrochemical machining is also exemplified in the article.

This article describes die wear and failure mechanisms, including thermal fatigue, abrasive wear, and plastic deformation. It summarizes the important attributes required for dies and the properties of the various die materials that make them suitable for particular applications. Recommendations on the selection of the materials for hot forging, hot extrusion, cold heading, and cold extrusion are presented. The article discusses the methods of characterizing abrasive wear and factors affecting abrasive wear. It discusses various die coatings and surface treatments used to extend the lives of dies: alloying surface treatments, micropeening, and electroplating.

This article introduces thermal spray coatings and describes the various types of coating processes and coating devices, including the flame spray, electric-arc spray, plasma spray, transferred plasma arc, high-velocity oxyfuel, and detonation gun. It provides information on the surface preparation methods and finishing treatments of coated parts. The article also explains the tests to evaluate the coating quality and the effects of coating structures and mechanical properties on coated parts. It concludes with a discussion on the uses of thermal spray coatings.

This article focuses on the modes of operation, physical basis, sample requirements, properties characterized, advantages, and limitations of the characterization methods used to evaluate the physical morphology and chemical properties of component surfaces for medical devices. These methods include light microscopy, scanning electron microscopy, atomic force microscopy, energy-dispersive X-ray spectroscopy, Auger electron spectroscopy, secondary ion mass spectrometry, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy.

This article discusses two basic forms of extrusion: cold and hot. It provides information on three types of extrusion processes, namely, direct extrusion, reverse extrusion, and hydrostatic extrusion. The article also discusses the mechanics, analysis, tooling and die design of extrusion as well as thermodynamics. The finite-element method suitable for simulation of metal forming processes is explained. The article examines the extrusion defects that are divided into three different categories including surface, subsurface, and internal type. It includes information on friction and lubrication modeling of extrusion processes. The article also discusses the fundamentals of extrusion technology of titanium alloys and aluminum. It concludes with information on two forms of wear in extrusion, namely, adhesive and abrasive wear.

The horsepower requirements to cut various metal alloys provide an indication of the relative ease and cost of machining, but several other important factors include cutting tool material, chip formation, cutting fluids, cutting tool wear, surface roughness, and surface integrity. This article reviews these general machining factors as well as specific cutting tool and cutting parameters for the six basic chip-forming processes of turning, shaping, milling, drilling, sawing, and broaching. Best practices for each of the six chip-forming processes are suggested for optimized machining of aluminum alloys. The article lists the inherent disadvantages of machining processes that involve compression/shear chip formation. It discusses the machining of aluminum metal-matrix composites and nontraditional machining of aluminum, such as abrasive jet, waterjet, electrodischarge, plasma arc, electrochemical, and chemical machining.

This article discusses the manufacturing steps and compositions of cemented carbides, as well as their microstructure, classifications, applications, and physical and mechanical properties. It provides information on new tool geometries, tailored substrates, and the application of thin and hard coatings to cemented carbides by chemical vapor deposition and physical vapor deposition. The article also discusses tool wear mechanisms and the methods available for holding the carbide tool.