1-20 of 94 Search Results for

flywheels

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 2005
Fig. 6 Flywheel slowdown, ram displacement, and forming load in upsetting of copper samples in a 1600 ton mechanical press. Source: Ref 4 More
Image
Published: 01 January 2006
Fig. 7 Flywheel slowdown and loss of energy during operation More
Image
Published: 01 January 1993
Fig. 6 Twin EBW-MV installation designed to weld a ring gear onto a flywheel. Courtesy of Leybold-Heraeus Vacuum Systems Inc. More
Image
Published: 01 January 2000
Fig. 5 Torsion testing machine. (a) Drive section. C, coupling; F, flywheel; M electric motor; O, output shaft; P, pillow block; AG, gear pair; GP, interchangeable gear pair; PR, planetary reducer; TB, timing belt drive. (b) Test section. H1, H2, specimen holders; I, low inertia coupling; L More
Image
Published: 01 January 2000
Fig. 15 Principle of high-rate tensile testing with flywheel setup More
Image
Published: 01 January 2005
Fig. 12 Energy versus load diagram for a screw press both without a friction clutch at the flywheel (dashed line) and with a slipping friction clutch at the flywheel (solid line). E W , nominal machine energy available for forging; L M , nominal machine load; E P , energy required More
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001381
EISBN: 978-1-62708-173-3
... such as flywheel mass, rotational speed, and axial force. It lists the advantages and limitations of FRW and provides a brief description on categories of applications of FRW such as batch and jobbing work and mass production. A table of process parameters of direct-drive FRW systems relative to inertia-drive FRW...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001349
EISBN: 978-1-62708-173-3
... a motor running at constant speed to input energy to the weld. The inertia-drive FRW uses the energy stored in a flywheel to input energy to the weld. The article summarizes some of the metals that have been joined by FRW and discusses the metallurgical considerations that govern the properties...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0003974
EISBN: 978-1-62708-185-6
... would slip and the press run would stop before reaching the bottom dead center position. If the condition expressed by Eq 2 is not satisfied, either the flywheel will slow down to unacceptable speeds in a mechanical press or the part will not be formed completely in one blow in a screw press or hammer...
Series: ASM Handbook
Volume: 6A
Publisher: ASM International
Published: 31 October 2011
DOI: 10.31399/asm.hb.v06a.a0005575
EISBN: 978-1-62708-174-0
... speed to input energy to the weld. Inertia-drive friction welding, sometimes called flywheel friction welding, uses the energy stored in a flywheel to input energy to the weld. These two FRW technologies produce inherently different metallurgical effects at the joint interface. Both FRW technologies...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005102
EISBN: 978-1-62708-186-3
..., and the operating parameters are discussed. The article provides information on the applications of rotary shearing. It concludes with a discussion on devices equipped with shearing machines for protecting personnel from the hazards of shear knives, flywheels, gears, and other moving parts. flywheels gears...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001366
EISBN: 978-1-62708-173-3
...-welding applications, including chain links, transmission bands, automotive flywheel ring gears, aircraft landing gear, band-saw blades, and crankshaft counter weights. It describes the components of a typical flash-welding machine. The article provides information on the electrical controls of flash...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001447
EISBN: 978-1-62708-173-3
... 1 depicts the parameter characteristics of the process. The inertia of the system is changed by either adding or removing flywheels from the rotating spindle that provides rotary motion and/or by changing the spindle speed. Fig. 1 Inertia welding parameter characteristics. Source: ANSI/AWS...
Image
Published: 01 January 2006
Fig. 26 Impact cutoff machine shearing bar stock with twin cutoff dies that are actuated by cam rollers on identical flywheel-cam assemblies More
Image
Published: 01 December 1998
Fig. 8 Screw press drive combining the characteristics of mechanical and screw presses. (a) Flywheel. (b) Air-operated clutch. (c) Screw. (d) Ram. (e) Lift-up cylinders More
Image
Published: 01 January 2005
Fig. 22 Screw press drive combining the characteristics of mechanical and screw presses. (1) Flywheel; (2) Air or hydraulic operated clutch; (3) Screw; (4) Ram; (5) Lift-up cylinders More
Image
Published: 01 January 2000
Fig. 2 Typical cam plastometer facility. Direct-current motor and generator are on the left; three flywheels and two transmissions are on the right; two-post loading frame is at rear. Courtesy of Los Alamos National Laboratory More
Series: ASM Handbook
Volume: 6A
Publisher: ASM International
Published: 31 October 2011
DOI: 10.31399/asm.hb.v06a.a0005596
EISBN: 978-1-62708-174-0
... from stored rotational kinetic energy. Figure 1 depicts the parameter characteristics of the process. The inertia of the system is changed by either adding or removing flywheels from the rotating spindle that provides rotary motion and/or by changing the spindle speed. Fig. 1 Inertia welding...
Image
Published: 01 January 1993
Fig. 4 Schematic showing effect of welding parameters on the finished weld nugget obtained when similar metals are welded using inertia-drive FRW equipment. (a) Flywheel energy. (b) Initial peripheral velocity of workpiece. (c) Axial pressure. Source: Ref 7 More
Image
Published: 31 October 2011
Fig. 5 Schematic showing effect of welding parameters on the finished weld nugget obtained when similar metals are welded using inertia-drive friction welding equipment. (a) Flywheel energy. (b) Initial peripheral velocity of workpiece. (c) Axial pressure. Source: Ref 12 More