1-12 of 12 Search Results for

flyer-plate experiment

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003303
EISBN: 978-1-62708-176-4
..., spallation fixtures, and the flyer-plate experiment, are also discussed. References References 1. Rankine W.J.M. , On the Thermodynamic Theory of Waves of Finite Longitudinal Disturbance , Philos. Trans. R. Soc. (London) , Vol 160 , 1870 , p 277 – 288 10.1098/rstl.1870.0015 2...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003304
EISBN: 978-1-62708-176-4
... experiment (shot No. 8-0131 in Table 4 ). (a) Second flyer plate. (b) Back momentum-trap plate. (c) Star-shaped flyer plate. (d) Fragmented specimen. Source: Ref 19 Abstract Abstract Impact tests are used to study dynamic deformation and failure modes of materials. This article discusses low...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003294
EISBN: 978-1-62708-176-4
... in compression, and rod impact (Taylor) test. The flyer plate impact test, expanding ring test, split-Hopkinson bar in tension, and a test using a rotating wheel used for high strain rate tension are also discussed. high strain rate compression test cam plastometer test the drop tower compression test...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001351
EISBN: 978-1-62708-173-3
... in explosion bonds resulting from changes in collision angle. The experimental setup consisted of the normal flyer plate arrangement used in the parallel gap technique, but with the base plate replaced by a half cylinder. Each bonding trial produced continuously changing flayer plate collision angles...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003295
EISBN: 978-1-62708-176-4
... is the particle velocity state for the flyer and anvil plates in the normal direction. Fig. 27 Loci of shear stress/transverse particle velocity states for flyer, anvil, and specimen. ν A is the anvil particle velocity and ν fs is the transverse particle velocity at the free surface of the anvil. V...
Series: ASM Handbook
Volume: 8
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.hb.v08.a0003293
EISBN: 978-1-62708-176-4
... <0.1 Conventional load frames 0.1–100 Special servohydraulic frames 100–10 3 Hopkinson (Kolsky) bar in tension 10 4 Expanding ring >10 5 Flyer plate Shear and multiaxial tests <0.1 Conventional shear tests 0.1–100 Special servohydraulic frames 10–10 3...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001449
EISBN: 978-1-62708-173-3
... 2. Smith E.G. Jr. , and Linse V.D. , The Acceleration Characteristics of Explosively Driven Flyer Plates , Proc. Sixth Int. Conf. High Energy Rate Fabrication ( Essen, West Germany ), 13–16 Sept 1977 3. Bahranni A.S. , Black T.G. , and Crossland B...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003500
EISBN: 978-1-62708-180-1
..., the importance of investigating failures is vividly illustrated in the pioneering efforts of the Wright Brothers in developing self-propelled flight. In fact, while Wilbur was traveling in France in 1908, Orville was conducting flight tests for the U.S. Army Signal Corps and was injured when his Wright Flyer...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006753
EISBN: 978-1-62708-295-2
... and was injured when his Wright Flyer crashed ( Fig. 1 ). His passenger sustained fatal injuries ( Ref 2 ). Upon receiving word of the mishap, Wilbur immediately ordered the delivery of the failed flyer to France so he could conduct a thorough investigation. This was decades before the formal discipline called...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003133
EISBN: 978-1-62708-199-3
...” drawing. Dies were made by punching a series of holes in a steel plate. Multiple wiredrawing machines were introduced around 1900. As a result, chilled cast iron plates and dies that could be reamed to size replaced the punch-sized, steel-plate dies. Lubricants were introduced because...
Book Chapter

By W.L. Johnson
Series: ASM Handbook
Volume: 2
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v02.a0001095
EISBN: 978-1-62708-162-7
... in an aqueous solution. When a current is passed through the electrolytic cell, these metal ions are collected on an anode. A film is built up on the anode as the process proceeds. This method has long been used in commercial plating. For example, electrolytically deposited nickel films have long been used...
Series: ASM Handbook
Volume: 2
Publisher: ASM International
Published: 01 January 1990
DOI: 10.31399/asm.hb.v02.a0001066
EISBN: 978-1-62708-162-7
..., formability, aesthetics Heat exchangers Alloy tube and plate Heat transfer, corrosion resistance (a) Although not specifically listed as a principal reason in all applications, ease of fabrication is a factor in all application categories. ASTM specifications for copper and copper alloy sheet...