1-20 of 1221

Search Results for extrusions

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006606
EISBN: 978-1-62708-210-5
.... aluminum alloy 2099 aluminum-copper-lithium alloys elastic modulus extrusions fatigue crack growth resistance high-strength alloys mechanical strength plates Alloy 2099 ( Table 1 ) is a third-generation Al-Cu–Li alloy introduced in 2003 to provide an improved combination of strength, elastic...
Image
Published: 30 November 2018
Fig. 25 Examples of soft and medium-grade alloy extrusions. Courtesy of Extrusions Inc. More
Image
Published: 15 June 2019
Fig. 1 Damage tolerance of 2055-T84 extrusions and 7 xxx extrusions. (a) toughness as a function of strength, (b) fatigue crack growth curves (L-T orientation). Note: T7E127 is Arconic’s internal designation for an age formable temper. Courtesy of Arconic, ATI- 2055 Fact Sheet More
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003015
EISBN: 978-1-62708-200-6
... Abstract This article describes the extrusion process, which converts soft, plastic material into a particular form using an extruder, or screw conveyer. It discusses the two main types of plastic extruders, twin-screw and single-screw, estimation of extruder capacity, and design and operations...
Image
Published: 01 January 1990
Fig. 2 Four examples of interconnecting extrusions that fit together or fit other products, and four examples of joining methods More
Image
Published: 01 January 1990
Fig. 3 Two examples of extrusions with nonpermanent interconnections More
Image
Published: 01 January 1990
Fig. 4 Six examples of interconnecting extrusions that lock together or lock to other products More
Image
Published: 01 January 1990
Fig. 9 Tensile properties of FVS-0812 alloy extrusions More
Image
Published: 01 January 1990
Fig. 7 Typical stress-strain curves for HM31A extrusions. Tested in longitudinal direction More
Image
Published: 30 September 2015
Fig. 14 The optimized Ti-6Al-4V BE powder-based extrusions (P4, P6, R6, and R7) da / dN behavior in comparison with back-to-back extruded IM-based Ti-6Al-4V material (R-4B-LT) extruded at the same temperature, strain rate, and extrusion ratio as all the other powder-based extrusions. Fatigue More
Image
Published: 01 January 1996
Fig. 1 Cottrell-Hull model for formation of intrusions and extrusions. Operation of two intersecting slip systems is assumed to occur in the sequence shown. More
Image
Published: 01 January 1996
Fig. 11 Model by Essmann et al. ( Ref 46 ) for formation of extrusions. (a) Arrangement of interface dislocations corresponding to an interstitial-type dislocation-dipole layer. (b) Extrusions formed by emergence of interface dislocations. b, Burgers vector; M, matrix; PSB, persistent slip More
Image
Published: 01 January 2005
Fig. 22 Finite element (FE) simulations and corresponding extrusions. These examples illustrate the degree to which commercially available three-dimensional FE software can predict metal flow through an extrusion die and the resulting distortion of the part. (a) The outward distortion More
Image
Published: 01 January 1989
Fig. 30 Original (a) and improved (b, c) methods of milling angle extrusions. Extrusions were 2.4 m (8 ft) long; each leg of L was 51 mm (2 in.) long and (before being milled) 7.9 mm ( 5 16 in.) thick. (a) In original method, each surface was milled separately—outside surfaces More
Image
Published: 01 January 2002
Fig. 50 Wavy slip. (a) Schematic of slip band extrusions in the matrix at a matrix-inclusion interface or at the surface of a notch. (b) Wavy slip lines (arrow) in oxygen-free, high-conductivity copper More
Image
Published: 01 December 1998
Fig. 9 Four examples of interconnecting extrusions that fit together or fit other products, and four examples of joining methods More
Image
Published: 01 December 1998
Fig. 10 Two examples of extrusions with nonpermanent interconnections More
Image
Published: 01 December 1998
Fig. 11 Six examples of interconnecting extrusions that lock together or lock to other products More
Image
Published: 15 January 2021
Fig. 51 Wavy slip. (a) Schematic of slip band extrusions in the matrix at a matrix/inclusion interface or at the surface of a notch. (b) Wavy slip lines (arrow) in oxygen-free, high-conductivity copper More
Image
Published: 31 December 2017
Fig. 2 Examples of extrusions and products made by sectioning them. Examples of extruded cross sections. (d) Courtesy of Plymouth Extruded Shapes More