1-20 of 801 Search Results for

extruding

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 November 2010
Fig. 5 Revolve and extrude operations. Extruding a two-dimensioned closed loop along an axis or rotating it about an axis defines very different solids More
Image
Published: 01 November 1995
Fig. 15 Flat die of type required for extruding film through water bath. Source: Ref 1 More
Image
Published: 01 January 2005
Fig. 29 Production of a large 4037 steel cap screw by extruding and heading in two blows. Dimensions given in inches More
Image
Published: 01 January 2005
Fig. 11 1030 steel (hardness: 75–80 HRB) axle-housing spindle produced by extruding and piercing in five operations. Dimensions given in inches More
Image
Published: 01 January 2005
Fig. 14 1018 steel adjusting-screw blank formed by forward extruding and severe cold heading. Dimensions given in inches More
Image
Published: 01 January 2005
Fig. 15 1039 steel rear-axle drive shaft produced by cold extruding an upset forging in three operations. Billet weight: 9.6 kg (21.2 lb). Dimensions given in inches More
Image
Published: 01 January 2002
Fig. 36 (a) Central bursting during extruding of AISI 4615 alloy steel specimen was promoted by (b) the presence of bainite and martensite (arrows point to microcracks in the martensite) in the as-rolled stock. Specimen etched with 4% picral, followed by 2% nital More
Image
Published: 01 January 2005
Fig. 6 Components and procedures employed in reverse extruding a cylinder blank More
Image
Published: 15 January 2021
Fig. 45 (a) Central bursting during extruding of AISI 4615 alloy steel specimen was promoted by (b) the presence of bainite and martensite (arrows point to microcracks in the martensite) in the as-rolled stock. Specimen etched with 4% picral, followed by 2% nital More
Image
Published: 01 January 2005
Fig. 1 Examples of extruded sections produced from easily extrudable aluminum alloys. Source: Ref 1 More
Image
Published: 01 January 2005
Fig. 12 Pierced and extruded propeller barrel forging with reverse-extruded flash. See Example 8 . Dimensions given in inches. More
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003015
EISBN: 978-1-62708-200-6
... Abstract This article describes the extrusion process, which converts soft, plastic material into a particular form using an extruder, or screw conveyer. It discusses the two main types of plastic extruders, twin-screw and single-screw, estimation of extruder capacity, and design and operations...
Image
Published: 30 September 2015
Fig. 10 Extruded polyethylene cracked from prolonged outdoor exposure More
Image
Published: 30 September 2015
Fig. 34 Pipe coating configuration showing (1) butyl rubber primer and (2) extruded polyethylene outer layer More
Image
Published: 01 June 2016
Fig. 76 Effects of heat treatments on dimensional changes in sheet and extruded rod. a: as-fabricated; b: annealed; c: solution heat treated and quenched in cold water; d: naturally aged, T4; e: precipitation heat treated, T6. Source: Ref 206 More
Image
Published: 01 January 1990
Fig. 21 Comparison of average low-cycle fatigue lives of HIP versus extruded and forged and versus HIP and forged René 95. Source: Ref 28 , 32 More
Image
Published: 01 January 1990
Fig. 15 Effect of stoichiometry on tensile properties of cast and extruded binary NiAl alloys. Nominal strain rate, 1.41 × 10 −3 /s. (a) Tested at room temperature. (b) Tested at 473 K. Source: Ref 106 More
Image
Published: 01 January 1990
Fig. 34 Typical mechanical properties of extruded and drawn C28000. Data are for Muntz metal rod less than 25 mm (1 in.) in diameter that was extruded and then cold drawn to various percentages of reduction in area. More
Image
Published: 01 January 1990
Fig. 39 Typical mechanical properties of extruded and drawn C37700. Data are for forging brass rod less than 25 mm (1 in.) diameter that was extruded, then cold drawn to various percentages of reduction in area. More
Image
Published: 15 June 2019
Fig. 2 Impact-extruded containers produced from 1 xxx alloy aluminum blanks More