1-15 of 15 Search Results for

explosive-driven shock-loading methods

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 17
Publisher: ASM International
Published: 01 August 2018
DOI: 10.31399/asm.hb.v17.a0006468
EISBN: 978-1-62708-190-0
... Built-in demagnetizers as contained in mobile equipment for magnetic-particle inspection are available that demagnetize by one of four methods: Low-voltage high-amperage alternating current with a motor-driven power-tap switch, arranged to automatically provide periods of current-on and periods of...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003063
EISBN: 978-1-62708-200-6
... permits powder weight loadings of about 85%. This level of loading presents the possibility of continuous prefiring and controlled shrinkage sintering. Virtually any material capable of being formed into a fine, stable powder can be spun with this method. The development of SiC fiber during the...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006797
EISBN: 978-1-62708-295-2
... stress above the design value or when the material strength is degraded. If either situation is a characteristic of the fabricated structure, the design must be changed to allow for these factors more realistically. When rapid or impulse loads are applied, as in impact, shock loading, or high...
Series: ASM Handbook
Volume: 4B
Publisher: ASM International
Published: 30 September 2014
DOI: 10.31399/asm.hb.v04b.a0005957
EISBN: 978-1-62708-166-5
... castable that is suitable for heat shock. Inside this perimeter, the car is insulated with insulating firebrick and surfaced with 5 cm (2 in.) cast slabs of castable for heavy-duty wear resistance. Alternately, cast piers for easy forklift loading can be provided. Low-mass cars also are available depending...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006753
EISBN: 978-1-62708-295-2
... without the use of a locking key, enabling the shaft to either drive or be driven anywhere on the shaft ( Fig. 8 ). The configuration consists of an assembly of four tapered rings ( Fig. 9 ) that are retained by a series of cap screws. As shown in Fig. 10 , when the screws are tightened, the middle wedge...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003053
EISBN: 978-1-62708-200-6
... solids loading for a given viscosity. Powder systems used with wet consolidation methods can be tested by determining the viscosity of the mix. Because the viscosity values are different for each system, the instrumentation required is different. Viscometers are available with an array of probes that...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003065
EISBN: 978-1-62708-200-6
... Abstract The large majority of the commercially important glasses are processed from a carefully calculated batch of raw materials that is then melted in special furnaces. Providing an introduction to melting practices of glass production, this article focuses on various finishing methods of...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005252
EISBN: 978-1-62708-187-0
... a problem, because it is driven off when the sand is heated to the minimum temperature of 120 °C (250 °F) before coating. Breakage of molds or cores during molding reflects low strength. This can be caused by the use of a finer sand screen distribution without a proportionate increase in resin...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003177
EISBN: 978-1-62708-199-3
... builders place the JIC markings in a prominent position on the fronts of the presses. Fig. 1 Designations used for press identification under the JIC classification system Power presses for sheet metal forming can be driven either hydraulically or mechanically. The performance...
Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.9781627081863
EISBN: 978-1-62708-186-3
Series: ASM Handbook
Volume: 5A
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.hb.v05a.9781627081719
EISBN: 978-1-62708-171-9
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003067
EISBN: 978-1-62708-200-6
.... Cost-driven compromises are often necessary. Some applications require precise control of one or more mechanical, physical, or chemical properties. Other applications require very little control, broad ranges of properties being acceptable. In many cases, close control of composition and properties...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0003991
EISBN: 978-1-62708-185-6
...), are preferred. Zero draft is possible on surfaces formed by the die and core rod, but not by the upper punch. Re-entrant angles (undercuts) cannot be forged. Axial tolerances–in the direction of forging—are driven by variations in the mass of metal in the preform. Lateral tolerances are...
Series: ASM Handbook
Volume: 4E
Publisher: ASM International
Published: 01 June 2016
DOI: 10.31399/asm.hb.v04e.a0006266
EISBN: 978-1-62708-169-6
... ramp temperatures upward sufficiently slowly, it may be possible to homogenize lower-melting areas during heatup in cast alloys. The result can be that the incipient melting temperature may be driven higher, allowing a corresponding increase in the allowable solution temperature. Aging of...
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 November 1995
DOI: 10.31399/asm.hb.emde.a0003009
EISBN: 978-1-62708-200-6
... lubricate the powder. The lubricated powder is then cold formed into a cylindrical billet, loaded into an extruder barrel, and driven by hydraulic or pneumatic pressure through the die. As it leaves the die, it passes through a multizone oven that removes the solvent and sinters the resin. Methods for...