This article describes selected U.S. environmental statutes and regulations that are pertinent to material surface finishers. It provides information on the applicability, requirements, and permitting conditions of the Clean Air Act, the Resources Conservation and Recovery Act, the Superfund Amendments and Reauthorization Act, and the Clean Water Act.

Ceramic and glass manufacturers take environmental regulations into consideration during all stages of the product cycle, from research and development to purchasing, processing, end use, and disposal. Ceramic and glass products are finding application in the construction industry and as raw materials for other processes. This article describes the recycling of in-process scrap and industrial wastes (fly ash, red mud, metallurgical waste, and other waste products), and applications of these recycled products. It focuses on environmental regulations such as Resource Conservation and Recovery Act and Clean Air Act. The Clean Air Act requires all states to meet minimum emissions standards for nitrogen-oxygen compounds, volatile organic compounds, and carbon monoxide.

This article describes the protective coatings technology used in naval aircrafts. It reviews the future needs and trends of the protective coatings technology based on advancing technology, environmental concerns, and operational requirements. The article discusses the standard finishing systems for aircrafts: the surface pretreatment system, primer, topcoat, advanced-performance topcoat, self-priming topcoat, and specialty coatings. It presents safe compliant solutions to environmental problems associated with the protective coatings technology. These solutions include the use of environmental regulations and hazardous materials, nonchromated pretreatments, waterborne technology, high-solids technology, and touch-up paints. The article also deals with the use of electrodeposition coatings, powder coatings, adhesive films, paint application equipment, and non-chromated sealants in the protective coatings technology.

The process of transferring coating materials from the container to the surface to be coated can be accomplished in a number of ways. This article describes seven methods of coating application: brushes, rollers, and daubers; conventional air spray; high-volume low-pressure spray; airless spray; air-assisted airless spray; plural-component spray; and electrostatic spray. Factors to be considered when deciding on an application method include the size and configuration of the surfaces to be coated, the type of coating being applied, environmental regulations/restrictions, the proximity to other operations or personnel, and the recommendations of the coating manufacturer.

The melting process often includes refining and treating the metal. The choice of which type of melting to use depends on a number of factors: type of alloy being melted, the local cost of electric power, and local environmental regulations. This article discusses the principles, furnace types, charging practices of metal melting methods, namely induction melting, cupola melting, arc melting, crucible melting, reaction melting, and vacuum melting, and the refractories and charging practice of reverberatory furnaces. Molten metal treatment of steels and aluminum also is discussed in the article.

This article is a general introduction to surface engineering of engineering components, providing an overview of the applications of surface treatments and the environmental protection regulations directly or indirectly related to surface engineering processes.

Environmental and worker health regulations have increased the costs associated with cadmium coating application and cadmium-beating waste disposal, thus creating economic incentives for industrial users to seek cadmium plating replacements. This article presents a cadmium replacement identification matrix that includes information on the specifications, corrosion control performance, environment-assisted cracking, coating lubricity, environmental and worker health regulations, and cost and performance factors for various replacement processes.

Grinding is an extremely complex process that requires the consideration of a number of elements in order to make a reasonably adroit initial selection of a fluid or fluids for a manufacturing plant. In addition, the disposal of grinding wastes must meet the minimum requirements as recommended by the federal Environmental Protection Agency (EPA) and Resource Conservation and Recovery Act (RCRA) regulations. This article explains the selection considerations of such fluids, as well as the applications and environmental issues related to the grinding processes.

This article discusses Allenby's two streams for environmental aspects of design: generic and specific concerns. Generic concerns include guidelines that provide the structure in which specific techniques can be developed and used. Specific methods are environmentally responsible for design and specific information that engineers can use. These methods include life cycle assessment, environmental impact assessment, quality function deployment, design for “X”, failure modes and effects analysis, and design for disassembly.

This article presents an overview of the different types of coating and lining materials available. It provides information on the various means of surface preparation and the equipment and techniques of coating application. The article discusses the coatings industry's response to the enacted as well as proposed legislation of limiting the use of potentially harmful or toxic raw materials or surface preparation and/or application techniques. The article summarizes the existing federal regulations affecting the coatings industry categorized according to the requirements of the Environmental Protection Agency and the Occupational Safety and Health Administration as well as the corresponding Code of Federal Regulation numbers.

Ash handling is a major challenge for utilities and industries using coal as a primary fuel. This article discusses the operating problems associated with conventional fly ash/bottom ash handling systems. It describes the two types of fly ash systems, namely, dry and wet fly ash systems. The article presents the ways to minimize operating problems that occur due to corrosion, erosion, scaling, and plugging.

This article discusses the commonly encountered forms of automotive body corrosion. The corrosion forms include general or uniform corrosion, cosmetic or under-film corrosion, galvanic corrosion, crevice corrosion, poultice or under-deposit corrosion, and pitting corrosion. Corrosion-resistant sheet metals, such as electrogalvanized steel, hot dip galvanized steel, and hot dip galvannealed steel, are reviewed. The article provides information on the paint and sealant systems for corrosion control in automotive body applications.

Explosion welding (EXW) is a solid-state metal-joining process that uses explosive force to create an electron-sharing metallurgical bond between two metal components. This article discusses the process attributes of EXW, including metallurgical attributes, metal combinations, size limitations, configuration limitations, and bond zone morphology. It provides an overview of the common industrial applications and shop welding applications of EXW products. The article reviews different safety standards and regulations, such as noise and vibration abatement and process geometry. It concludes with a section on the EXW process sequence for welding a two-component flat plate product.

This article presents a background of green chemistry and green coatings, and a summary of the key concerns of the green coating procurement process. It includes a discussion on green marketing and the seven sins of greenwashing, an overview of the environmental certification standards and regulatory environments, and the importance of performance during the duty cycle.

This article discusses the factors affecting corrosion behavior. It describes galvanic corrosion and its protection methods. The article also provides information on coatings and inhibitors, which are used in corrosion protection.

The chemicals that have been used in traditional vapor degreasing have serious health and environmental hazards that have prompted the search for modified and alternative techniques. This article provides a detailed discussion on the regulatory mandates that affect the use of industrial degreasing methods. It describes the aqueous degreasing technique, which forms an attractive alternative to the traditional vapor degreasing process. The article includes information on the materials and equipment used in the process, and discusses the advantages and disadvantages of hot and dip tank systems of aqueous degreasing. It explains how to convert an existing vapor degreaser to an aqueous cleaning system.

This article describes the process of selecting an optimum coating and material system for a specific application. It reviews critical coating functions that influence the coating selection process, and presents some application success stories. The article explores the benefits of thermal spray coatings and functions they provide. It also presents key references from various National Thermal Spray Conference, United Thermal Spray Conference, and International Thermal Spray Conference Proceedings from 2006 through 2012.

This article discusses the occupational health hazards related to industrial protective coating application and removal. It explains the health hazards associated with coating constituents such as lead, cadmium, chromium, arsenic, silica, and asbestos. The article also discusses hazard evaluation, hazard controls, Occupational Safety and Health Administration standards, and industry consensus standards. It concludes with a description of containment systems to prevent environmental exposures from industrial paint removal projects.

This article provides an overview of the concepts of environmental, health, and safety (EH&S) risk incidents, then discusses these concepts relative to additive manufacturing (AM): the multiple intrants, process parameters, and equipment, as well as the resulting products and wastes. The article discusses additive manufacturing hazards, which are broken down into material hazards, equipment/process hazards, and facility hazards. The environmental impact of AM and the development of EH&S standards for AM also are covered in the article.

Alkaline cleaning is a commonly used method for removing a wide variety of soils from the surface of metals. This article focuses on the composition, operating conditions, and test and control of alkaline cleaners, as well as equipment used and their application methods. It describes the mechanisms of alkaline cleaning, such as saponification, displacement, emulsification and dispersion, and metal oxide dissolution. The article concludes with information of the safety and environmental considerations in the usage of alkaline cleaners.