1-20 of 262 Search Results for

engine coolant base components

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004164
EISBN: 978-1-62708-184-9
... that occur in cooling systems, including uniform corrosion, galvanic corrosion, crevice corrosion, pitting corrosion, intergranular corrosion, erosion corrosion, and cavitation corrosion. The article presents information on engine coolant base components and inhibitors used for corrosion prevention...
Book Chapter

Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004221
EISBN: 978-1-62708-184-9
... corrosion caused perforation at the exhaust valve port of this aluminum cylinder head. See the article “Engine Coolants and Coolant System Corrosion” in this Volume. Fig. 27 High-temperature oxidation of the tip of an industrial gas turbine blade. Below the tip, a coating is protecting the base...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002151
EISBN: 978-1-62708-188-7
... for chip clearance and/or the introduction of coolant. It describes the compositions and applications of coated abrasives and types of grinding fluids, such as petroleum-base and mineral-base cutting oils, water-soluble oils, synthetic fluids, semisynthetic fluids, and water plus additives. The article...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004145
EISBN: 978-1-62708-184-9
.... Brown K.S. and Gordon G.M. , Effects of BWR Coolant Chemistry on Propensity for IGSCC Initiation and Growth in Creviced Reactor Internals Components , Proc. Third Int. Symposium on Environmental Degradation in Nuclear Power Systems—Water Reactors ( Traverse City, MI ), Aug 30–Sept 3, 1987...
Series: ASM Handbook
Volume: 5B
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v05b.a0006035
EISBN: 978-1-62708-172-6
... that these operations will continue without radiation exposure to the workers, the public, and the environment, even in the event of accidents, the plants have been designed with layers of interlocking, engineered safety systems. The loss-of-coolant accident has been identified as the DBA that can rapidly de-water...
Series: ASM Handbook
Volume: 9
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.hb.v09.a0003746
EISBN: 978-1-62708-177-1
... component to more closely match the heating and cooling rate of the surface of the component. Because the surface layers are the most critical in many engineering applications, this may be a helpful procedure. A common practice among heat treaters that should be questioned is that of making up a large...
Book Chapter

By K. Subramanian
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002152
EISBN: 978-1-62708-188-7
..., kiln furniture Plastics and composites Fiber-reinforced plastics, friction materials, optical lenses Electronic ceramics Integrated circuit chip fabrication, magnetic heads, sensors, optical fibers Engineering ceramics Internal combustion engine parts, wear-resistant parts and bearings...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001241
EISBN: 978-1-62708-170-2
... alloy and each coolant were normalized to the grindability of Inco 718 using water-soluble coolant to determine the relative grindability. (2) The above data are based on limited data sets and should be used only as a guideline. Physical and mechanical properties of selected ceramics, metals...
Series: ASM Handbook
Volume: 22B
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.hb.v22b.a0005503
EISBN: 978-1-62708-197-9
..., which is called fountain flow, and special problems arise with thick parts with sudden thickness changes, which cause racetrack , several 3-D computer-aided engineering simulations exist that successfully predict conventional plastic advancement and pressure variation with changes in component design...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002192
EISBN: 978-1-62708-188-7
... contains enough coolant to submerge the chips. These fine chips may ignite, but there is insufficient material to support a large fire. Uranium and uranium alloys are ground when necessary using water base coolant and a silicon wheel. Grinding of uranium is difficult. Due to the relatively low thermal...
Series: ASM Handbook
Volume: 18
Publisher: ASM International
Published: 31 December 2017
DOI: 10.31399/asm.hb.v18.a0006363
EISBN: 978-1-62708-192-4
...-1648(99)00361-0 29. Abele E. and Schramm B. , Using PCD for Machining CGI with a CO2 Coolant System , Prod. Engineer ., Vol 2 ( No. 2 ), 2008 , p 165 – 169 10.1007/s11740-008-0104-6 30. Machai C. and Biermann D. , Machining of β-Titanium-Alloy Ti-10V-2Fe...
Series: ASM Handbook
Volume: 5
Publisher: ASM International
Published: 01 January 1994
DOI: 10.31399/asm.hb.v05.a0001232
EISBN: 978-1-62708-170-2
... and provides lubrication. Mineral oil or mineral seal oil are conventional fluids that meet these requirements and still have low enough odor and high enough flash point to be feasible and safe. Water-based coolants have specific applications, and some workpieces composed of carbon and other ceramics are often...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005267
EISBN: 978-1-62708-187-0
...Abstract Abstract This article describes the melting process of casting metals used in hot chamber die casting. It discusses the design and capabilities of injection components, such as gooseneck, plunger, and cylinder. The article reviews the distinctions between hot and cold chamber processes...
Series: ASM Handbook
Volume: 13A
Publisher: ASM International
Published: 01 January 2003
DOI: 10.31399/asm.hb.v13a.a0003610
EISBN: 978-1-62708-182-5
... Reactor Components,” Paper 106, presented at Corrosion/78, National Association of Corrosion Engineers , 1978 • Fleitman A.H. and Weeks J.R. , Mercury as a Nuclear Coolant , Nucl. Eng. Des. , Vol 16 ( No. 3 ), 1971 10.1016/0029-5493(71)90015-X • Harrison J.D...
Series: ASM Handbook
Volume: 20
Publisher: ASM International
Published: 01 January 1997
DOI: 10.31399/asm.hb.v20.a0002457
EISBN: 978-1-62708-194-8
... implementation of change Probe tip material change Lab test immersed in coolant at high temperature and pressure Verify plan with customer release engineer Relocation of assembly area Discuss in advance with Human Resources Establish rigorous quality constraints Discuss with union Change...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002127
EISBN: 978-1-62708-188-7
... PCBN cutting edge after machining 2600 gray cast iron engine block bores Fig. 16 Effect of coolant on the flank wear of PCBN tools after 20 min of cutting. Machining parameters: cutting speed = 50 m/min (165 sfm); feed rate = 0.7 mm/rev (0.028 in./rev); depth of cut = 8 mm (0.315...
Series: ASM Handbook
Volume: 13C
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v13c.a0004146
EISBN: 978-1-62708-184-9
...) components fabricated from nickel-base alloys Table 6 Pressurized water reactor (PWR) components fabricated from nickel-base alloys PWR components Nickel-base alloy grades used Steam generator tubes 600 MA and TT, 690 TT and 800 Steam generator divider plates 600 and 690 Upper head...
Series: ASM Handbook
Volume: 7
Publisher: ASM International
Published: 30 September 2015
DOI: 10.31399/asm.hb.v07.a0006104
EISBN: 978-1-62708-175-7
.../rev; depth of cut = 0.5 mm. Criteria: V b = 0.25 mm, dry. Tool: PVD-TiN coated Influence of liquid coolant and oil impregnation on flank wear Table 1 Influence of liquid coolant and oil impregnation on flank wear Material Composition Flank wear, mm Oil impregnated Cutting fluid...
Series: ASM Handbook
Volume: 1A
Publisher: ASM International
Published: 31 August 2017
DOI: 10.31399/asm.hb.v01a.a0006306
EISBN: 978-1-62708-179-5
... Machining Parameters Cutting Lubrication (Coolants) Dry Machining As-Cast Surface Geometry Skin Layers in GI Phases in Matrix Microstructure of Gray Irons Effect of Graphite Shape Inclusion Engineering Solution-Strengthened (SS) Ferritic SGI...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002179
EISBN: 978-1-62708-188-7
... of Nonleaded Free-Machining Steels—Phase II,” DSS Contract No. USU80—0011, McMaster University , March 1983 23. Machining Principles , Metals Engineering Institute, ASM INTERNATIONAL 24. Repars J.E. and Brockman R.W. , How Coolants Affect Drill Wear , Am. Mach. , Feb 1971...