1-20 of 444 Search Results for

drive shaft

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 December 1998
Fig. 43 Fracture surface of a carbon-steel drive shaft of a tug boat. The shaft failed by corrosion fatigue after seawater displaced the lubricant between the shaft and the stern tube. Beach marks indicate that the fracture origin was at left (arrow). 0.8├Ś More
Image
Published: 01 January 2006
Fig. 21 Schematic of aluminum alloy 6063-T832 drive shaft with ends attached to drawn aluminum shaft by electromagnetic forming (EMF). Source: Ref 32 More
Image
Published: 01 January 2005
Fig. 15 1039 steel rear-axle drive shaft produced by cold extruding an upset forging in three operations. Billet weight: 9.6 kg (21.2 lb). Dimensions given in inches More
Image
Published: 01 January 1987
Fig. 51 Macrograph of the fracture face of an AISI 4320 drive shaft that failed by fatigue. The failure began at the end of a keyway that was machined without fillets (B) and progressed to final rupture at (C). The final rupture zone is small, indicating that loads were low. More
Image
Published: 01 January 1987
Fig. 152 Fracture surface of a carbon steel drive shaft of a 180-Mg (200-gross-ton) marine tug. The shaft failed by corrosion fatigue after seawater displaced the lubricant between the shaft and the stern tube. Beach marks indicate that the fracture origin was at left (arrow). See also Fig More
Image
Published: 01 January 1987
Fig. 153 Side view of the fractured drive shaft in Fig. 152 . Note the serrated profile (retouched for clarity) of this edge of the fracture surface and the diagonal cracks on the shaft surface. The cracks were caused by corrosion fatigue from the combination of reversed shaft torsion More
Series: ASM Handbook
Volume: 12
Publisher: ASM International
Published: 01 January 1987
DOI: 10.31399/asm.hb.v12.a0000605
EISBN: 978-1-62708-181-8
..., automotive bolts, hydraulic jack shafts, crank handle collars, boiler tubes, drive shafts, bicycle pedal axles, lift-truck hydraulic-piston rods, and steel springs. boilers delayed fracture fatigue crack propagation fatigue fracture fractograph impact fracture intergranular fracture low-carbon...
Image
Published: 01 August 2018
Fig. 41 Forged drive-pinion shaft and coupling in which the detection of a crack during preventive maintenance magnetic-particle inspection prevented a costly breakdown. (a) Drive-pinion shaft and coupler assembly; arrows show locations of fillets on wobbler coupling half that were inspected More
Image
Published: 01 January 1987
Fig. 342 Fatigue fracture in an AISI 4140 steel tail-rotor drive-pinion shaft of a helicopter, heat treated to a hardness of 35 HRC. See also Fig. 343 , 344 , 345 , and 346 . Actual size More
Series: ASM Handbook
Volume: 12
Publisher: ASM International
Published: 01 January 1987
DOI: 10.31399/asm.hb.v12.a0000607
EISBN: 978-1-62708-181-8
...-embrittlement fracture, fatigue crack propagation, and corrosion fatigue of components made from high-carbon steels. The high-carbon steel components include bull gear, drive shaft, power boiler stoker grate, steel wheel, spring wire, suspension spring, automotive engine valve spring, power spring, cantilever...
Image
Published: 01 December 1998
Fig. 26 Cross section of four-hammer radial forging machine with mechanical drive. (a) Eccentric shaft. (b) Sliding block. (c) Connecting rod. (d) Adjustment housing. (e) Adjusting screw. (f) Hydraulic overload protection. (g) Hammer adjustment drive shafts More
Image
Published: 30 August 2021
Fig. 32 Shaft assembly in which the height of the pillow-block bearing caused misalignment of the extension shaft with the drive shaft, resulting in bending-fatigue fracture More
Image
Published: 01 January 2002
Fig. 22 Shaft assembly in which the height of the pillow-block bearing caused misalignment of the extension shaft with the drive shaft, resulting in bending-fatigue fracture. More
Image
Published: 01 January 2005
Fig. 2 Four-hammer radial forging machine with mechanical drive. (a) Cross section through forging box. (b) Longitudinal section through forging box. 1, eccentric shaft; 2, sliding block; 3, connecting rod; 4, adjustment housing; 5, adjusting screw; 6, hydraulic overload protection; 7, hammer More
Image
Published: 01 August 2018
Fig. 27 Black light used to reveal magnetic-particle indication of a crack in the centering stud of a ball-yoke-type universal-joint section of a drive-shaft assembly. Courtesy of Magnaflux Corporation More
Image
Published: 01 January 2005
Fig. 3 Schematic diagram of a mill for radial roll forming of turbine disk type components. The diagram shows the main drive shaft, the axial-radial working rolls, the outer radial working rolls, and the workpiece More
Image
Published: 01 January 2002
Fig. 8 Fuel pump that failed by vibration and abrasion. (a) Configuration and dimensions (given in inches). (b) Splines on the drive shaft and in the impeller were worn away by vibration in the presence of sand and metallic particles. Detail A: Enlarged view of failure area showing worn More
Image
Published: 30 August 2021
Fig. 8 Fuel pump that failed by vibration and abrasion. (a) Configuration and dimensions (given in inches). OD, outside diameter. (b) Splines on the drive shaft and in the impeller were worn away by vibration in the presence of sand and metallic particles. Detail A: Enlarged view of failure More
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001808
EISBN: 978-1-62708-180-1
..., as well as how their alignment may be affected by deflections or distortions that can occur as a result of mechanical loads, shock, vibrations, or thermal gradients, should be considered. The method of connecting the driving or driven member to the shaft, such as press fitting, welding, or use...
Series: ASM Handbook
Volume: 12
Publisher: ASM International
Published: 01 January 1987
DOI: 10.31399/asm.hb.v12.a0000608
EISBN: 978-1-62708-181-8
..., sulfide stress-corrosion failure, stress-corrosion cracking, and hitch post shaft failure of these steels. The components considered in the article include tail-rotor drive-pinion shafts, pinion gears, outboard-motor crankshafts, bull gears, diesel engine bearing cap bolts, splined shafts, aircraft...