1-20 of 161

Search Results for diaphragms

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 January 2002
Fig. 24 Diaphragms and girders in a continuous-span structure. More
Image
Published: 31 December 2017
Fig. 9 Elastomeric diaphragms. (a) Convoluted diaphragm. (b) Rolling diaphragm. Source: Ref 15 More
Series: ASM Handbook Archive
Volume: 21
Publisher: ASM International
Published: 01 January 2001
DOI: 10.31399/asm.hb.v21.a0003425
EISBN: 978-1-62708-195-5
...-impregnated thermoplastics, and true thermoplastics. It describes the processing methods of thermoplastic composites, including weaving, seaming, autoclaving, preconsolidation, roll consolidation, roll forming/pultruding, thermoforming, press forming, hydroforming, and diaphragm forming. The article provides...
Image
Published: 01 January 2002
Fig. 40 Widening of cracks from the diaphragm region of the part shown in Fig. 39 . 10.4× More
Image
Published: 01 December 1998
Fig. 36 Principals of SAAB rubber-diaphragm (fluid forming) method. The air vents keep trapped air from causing blisters on the workpiece. More
Image
Published: 15 May 2022
Fig. 12 A diaphragm gate was placed at the center of this bezel so that knit lines would be located far away from the thin webs between openings. The molder was instructed to machine the gate off the surface to avoid interferences between assembled parts. More
Image
Published: 01 January 2006
Fig. 16 Fluid-cell forming in a Hydroform press with rubber diaphragm More
Image
Published: 01 January 2006
Fig. 21 Principal components of SAAB rubber-diaphragm (fluid forming) method. The air vents keep trapped air from causing blisters on the workpiece. More
Image
Published: 01 January 2006
Fig. 25 Hydraulic forming with diaphragm More
Image
Published: 01 August 2018
Fig. 28 Use of a combination of metallic shot, a lead mask, and a lead diaphragm to control scattered radiation More
Image
Published: 01 August 2018
Fig. 29 Use of a lead diaphragm to limit the included angle of the x-ray beam, and use of a filter to reduce subject contrast and to eliminate much of the secondary radiation that causes undercutting More
Image
Published: 01 August 2018
Fig. 22 Use of a combination of metallic shot, a lead mask, and a lead diaphragm to control scattered radiation More
Image
Published: 01 August 2018
Fig. 23 Use of a lead diaphragm to limit the included angle of the x-ray beam, and use of a filter to reduce subject contrast and to eliminate much of the secondary radiation that causes undercutting More
Image
Published: 01 January 2001
Fig. 5 Schematic of thermoplastic diaphragm forming in press More
Image
Published: 01 January 2001
Fig. 6 Schematic of thermoplastic diaphragm forming in autoclave More
Image
Published: 01 January 2001
Fig. 8 Thermoplastic diaphragm forming More
Image
Published: 01 January 1993
) For brazing the subassembly and simultaneously solution heat treating the 17-7 PH diaphragms. (c) Achieved by running the dissociated ammonia through a molecular-sieve dryer after cracking. (d) Cross-sectional dimensions (and product forms) of preplaced rings were: for joint between diaphragm and top More
Image
Published: 01 January 2006
Fig. 17 Original and improved methods of forming a fuel-nozzle swirl cup for a turbojet engine. (a) Part formed by original method; six press-formed sections welded together. (b) Partly drawn blank ready for rubber-diaphragm forming. (c) Punch of six similar wedge-shaped segments doweled More
Book Chapter

By John W. Fisher
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001821
EISBN: 978-1-62708-180-1
... plates, multiple-girder diaphragm connection plate, and tied-arch floor beams. bridge distortion fatigue strength floor-beam-girder connection plates multiple-girder diaphragm connection plate tied-arch floor beams welds FROM 1960 TO 1986, a number of localized failures developed...
Book Chapter

Series: ASM Handbook
Volume: 14B
Publisher: ASM International
Published: 01 January 2006
DOI: 10.31399/asm.hb.v14b.a0005124
EISBN: 978-1-62708-186-3
..., and the Demarest process. The article provides a discussion on the procedures of these processes, as well as the presses and tools used. It describes the methods of hydraulic forming of thin metal parts, namely, hydraulic forming with diaphragm, hydraulic forming with gasket and pressure control, and hydrobuckling...