1-20 of 522 Search Results for

cutting fluid recommendations

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003192
EISBN: 978-1-62708-199-3
... , 58 , 59 , 60 , and 61 ; for recommended cutting fluids, see Table 62 . (a) Caution: Check horsepower requirements on heavier depths of cut. Face milling, free-machining low carbon steels, wrought Table 2 Face milling, free-machining low carbon steels, wrought Material Hardness...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003193
EISBN: 978-1-62708-199-3
..., 1 12 of wheel width) A46HV 300–475 ST and A 3000–3500 50–100 R: 0.001; F: 0.0005 max 0.020–0.200 (max, 1 12 of wheel width) A46HV See Table 62 in the preceding article ( “Machining Data Recommendations” ) for cutting fluid recommendations. (a) A, annealed; A-C...
Book Chapter

Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002131
EISBN: 978-1-62708-188-7
..., accommodates cutting fluid flow from the inside diameter of the bar and exhausts the fluid on the outside diameter. Recommended maximum depths for holes trepanned with outside-diameter-exhaust heads are as follows: Diameter Depth mm in. mm in. 50–64 2–2 1 2 610–762 24–30 65–89...
Book Chapter

By Mark Johnson
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002139
EISBN: 978-1-62708-188-7
... life. Cutting fluids recommended for pipe tapping are the same as those used for the cutting of machine threads. A constant supply of fluid to the cutting area is generally more important in pipe threading than in cutting machine threads because more cutting teeth are engaged at one time in pipe...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002178
EISBN: 978-1-62708-188-7
... cutting fluids for titanium  92 biodegradable soluble oils Cutting fluid recommendations for cast irons Table 5 Cutting fluid recommendations for cast irons See Table 4 for identification of cutting fluid code numbers. Operation Tool material Cutting fluid code No. Turning...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002187
EISBN: 978-1-62708-188-7
... Direction Depth of Cut Speeds and Feeds Blade Design Speeds and Feeds Cutting fluids should be applied generously to the tool-workpiece contact area. Dry machining is not recommended, but is practiced successfully in some cases when small amounts of metal are removed. Emulsifiable oils...
Book: Machining
Series: ASM Handbook
Volume: 16
Publisher: ASM International
Published: 01 January 1989
DOI: 10.31399/asm.hb.v16.a0002186
EISBN: 978-1-62708-188-7
... cooling. If a particular job or machine tool precludes the use of a cutting fluid, cutting speed should be reduced to less than 150 m/min (500 sfm), and the recommendations regarding tools and feeds should be carefully followed. When tapping and reaming, there is the possibility of chip jamming...