Search Results for cleaning equipment

This article describes the eight chemical cleaning methods, namely, circulation, fill and soak, cascade, foam, vapor-phase organic, steam-injected, on-line chemical, and mechanical cleaning. It presents information on deposit types, solvents used to remove them, and construction material incompatibilities in a table. The article summarizes the uses of chemical cleaning solutions, including hydrochloric acid, phosphoric acid, and sulfamic acid, as well as the additives used to neutralize their impact on corrosion. It discusses the chemical cleaning procedures, including selection of cleaning method and solvent, documentation of cleaning, and corrosion monitoring in chemical cleaning.

Ultrasonic cleaning involves the use of high-frequency sound waves that is above the upper range of human heating, or about 18 kHz, to remove a variety of contaminants from parts immersed in aqueous media. This article describes the process, design considerations and the equipment in ultrasonic cleaning. The components used in the generation of ultrasonic wave include piezoelectric and magnetostrictive transducers that are used in ultrasonic generators and tanks. The effects of solution type and its temperature on the effectiveness of ultrasonic cleaning are also discussed.

This article focuses on the mineral and organic acid cleaning of iron and steel. It begins with a discussion on the application methods, process selection criteria, solution composition, equipment used, and control of process variables in mineral acid cleaning. The article then describes the advantages and disadvantages of organic acid cleaning. Applications, including boiler cleaning, stainless steel cleaning, and removal of iron- and copper-bearing deposits, are discussed. The article concludes with an overview of acid cleaning of nonferrous alloys.

Mechanical cleaning systems are used to remove contaminants of work surface by propelling abrasive materials through any of these three principal methods: airless centrifugal blast blade- or vane-type wheels; compressed air, direct-pressure dry blast nozzle systems; or compressed-air, indirect-suction (induction) wet or dry blast nozzle systems. This article focuses on the abrasive media, equipment, applications, and limitations of dry and wet blast cleaning. It discusses the health and safety precautions to be taken during mechanical cleaning.

Alkaline cleaning is a commonly used method for removing a wide variety of soils from the surface of metals. This article focuses on the composition, operating conditions, and test and control of alkaline cleaners, as well as equipment used and their application methods. It describes the mechanisms of alkaline cleaning, such as saponification, displacement, emulsification and dispersion, and metal oxide dissolution. The article concludes with information of the safety and environmental considerations in the usage of alkaline cleaners.

This article provides information on the factors influencing the selection of the proper corrosion-resistant coating system. It focuses on the proper execution of surface preparation and the available surface preparation methods. The preparation process includes the removal of visible contaminants, removal of invisible contaminants, and roughening of the surface. Solvent or chemical washing, steam cleaning, hand tool cleaning, power tool cleaning, water blasting, and abrasive blast cleaning, are some preparation methods discussed. The article describes the most common application techniques of coating as well as the equipment used. An overview of some of the most common coating inspection points and inspection equipment is also provided.

Emulsion cleaning is an industrial cleaning process that uses an organic solvent as the main active agent. This article provides information on the applications, concerns and limitations, and process parameters of emulsion cleaning. It describes the processing variables and equipment for three main stages of emulsion cleaning: immersion cleaning, secondary cleaning, and spray cleaning. In addition, the classifications, composition, and selection criteria are also discussed.

Solvent cleaning is a surface preparation process that can be accomplished in room temperature baths (cold cleaning ) or by condensing vapors of a solvent on a workpiece (vapor degreasing). This article provides a detailed discussion on solvents, equipment, process limitations and applications, and safety and health hazards of cold cleaning and vapor degreasing. It also includes information on control of contamination, conservation and recovery of solvent, and disposal of solvent wastes.

Materials of construction for equipment and piping in pharmaceutical processing plants must be resistant to corrosion from the high-purity water, the buffer solutions used in preparation of the products, and the cleaning solutions used to maintain the purity of the product. The primary water used in pharmaceutical production is water for injection (WFI). This article presents the steps for preparing WFI and discusses the effect of chlorides on stainless steel. It provides information on the passive layer of stainless steels and chromium-containing nickel alloys. The article provides information on the surface finish of pharmaceutical equipment. It discusses the classification of rouge and the characteristics of cast type 316L stainless steel. The article also explains how and when to perform cleaning and repassivation process on classes of rouge.

Molten salt baths are anhydrous, fused chemical baths used at elevated temperatures for a variety of industrial cleaning applications. This article discusses their applications in paint stripping, polymer removal, casting cleaning, glass removal, and plasma/flame spray removal. It provides an overview of the basic design and safety considerations of the salt bath equipment and describes the environmental impact of molten salt bath cleaning.

This article focuses on the types, composition, and applications of phosphate coatings and describes the characteristics of phosphate-coated ferrous and nonferrous materials, including steel and aluminum. It addresses five successive process fundamentals: cleaning, rinsing, phosphating, rinsing after phosphating, and chromic acid rinsing. The article describes the techniques for controlling the chemical composition of various phosphating solutions. It discusses the equipment and factors that influence equipment requirements in immersion and spray systems. The article also describes the controlling procedures of coating weight and crystal size. It provides guidelines for choosing phosphate coatings based on application, coating weight requirements, and recommended process parameters. The article concludes with a discussion on safety precautions and the treatment of effluents from phosphating plants.

This article begins with a description of the advantages and disadvantages of thermal spraying. It provides a discussion on the importance of substrate processing prior to coating and the role of undercutting in repair. The article reviews the steps for substrate preparation, namely, cleaning, roughening, masking, and preheating. Information on the equipment and process variables of dry abrasive grit blasting are also provided. The article describes the roles of spray stream and the spray pattern for all thermal spray processes. It discusses the defects arising from poor temperature control and from the variables influencing the manipulation of the spray torch. The article concludes with helpful information on calculating the process efficiency of thermal spraying.

Coatings, such as those applied to ships, must be resistant to abrasion, in the case of cargo hold coatings, and cyclic changes of chemicals and tank cleaning, in the case of tank linings. Failures and defects can manifest themselves at various times in the life of a coating. To determine the cause and mechanism of coating failure, all possible contributory factors must be evaluated together with a detailed history from the time of application to the time the failure was first noted. Many coating failures require further evaluation and analysis to be carried out by a qualified chemist or coating specialist, often using specialized laboratory equipment. The article presents examples of coating failures and defects, together with descriptions, probable causes, and suggested preventative measures.

This article begins with discussion on forgeability and the factors affecting the forgeability of aluminum and aluminum alloys. It describes the types of forging methods and equipment and reviews critical elements in the overall aluminum forging process: die materials, die design, and die manufacture. The article discusses the critical aspects of various manufacturing elements of aluminum alloy forging, including the preparation of the forging stock, preheating stock, die heating, lubrication, trimming, forming and repair, cleaning, heat treatment, and inspection. It concludes with a discussion on the forging of advanced aluminum materials and aluminum alloy precision forgings.

Titanium alloys are forged into a variety of shapes and types of forgings, with a broad range of final part forging design criteria based on the intended end-product application. This article begins with a discussion on the classes of titanium alloys, their forgeability, and factors affecting forgeability. It describes the forging techniques, equipment, and common processing elements associated with titanium alloy forging. The processing elements include the preparation of forging stock, preheating of the stock, die heating, lubrication, forging process, trimming and repair, cleaning, heat treatment, and inspection. The article presents a discussion on titanium alloy precision forgings and concludes with information on the forging of advanced titanium materials and titanium aluminides.

Stainless steels, based on forging pressure and load requirements, are more difficult to forge because of the greater strength at elevated temperatures and the limitations on the maximum temperatures at which stainless steels can be forged without incurring microstructural damage. This article discusses the forging methods, primary mill practices (primary forging and ingot breakdown), trimming, and cleaning operations of stainless steels. It describes the use of forging equipment, dies, and die material in the forging operation. The article provides an overview of the forgeability of austenitic stainless steels, martensitic stainless steels, precipitation-hardening stainless steels, and ferritic stainless steels. It concludes with a discussion on the heating and lubrication of dies.

Precipitation hardening is a hardening mechanism found in various steels and alloy systems, such as nickel-, cobalt-, titanium-, copper-, and iron-base alloys. This article provides a brief description of precipitation hardening process, furnace equipment, surface-related problems, and protective atmospheres used in heat treatment of iron-base precipitation-hardenable (PH) superalloys. It focuses on various factors to be considered in heat treating of PH stainless steels: cleaning prior to heat treatment, furnace atmospheres, time-temperature cycles, variations in cycles, and scale removal after heat treatment. The article describes the mechanical properties, solution treatment, and aging treatment for many martensitic PH alloys, including: Alloy 17-4 PH, Alloy 13-8 Mo, Alloy 15-5 PH, Custom 450, and Custom 455; as well as semiaustenitic PH stainless steels such as Alloy 17-7 PH, Alloy PH 15-7 Mo, AM-350, Pyromet 350, AM-355, and Pyromet 355; austenitic PH stainless steel, A-286; cast PH stainless steels; and iron-nickel PH superalloys.