1-20 of 437 Search Results for

clad metals

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 13B
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v13b.a0003834
EISBN: 978-1-62708-183-2
... Abstract This article describes the principal cladding processes and methods for calculating properties of clad metals. It reviews the designing processes of clad metals to achieve specific requirements. The article discusses six categories of clad metal systems designed for corrosion control...
Image
Published: 01 January 2005
Fig. 1 Categorization of clad metals as bonded metal-metal laminar composite systems More
Image
Published: 01 January 2005
Fig. 2 High-volume commercially available clad metals More
Image
Published: 31 October 2011
Fig. 17 Schematic illustration of the roll welding process producing clad metals or bimetal strips of sheet. Source: Ref 5 More
Image
Published: 01 December 1998
Fig. 3 Bond zone pattern typical of explosion clad metals. Materials are type 304L stainless steel and medium-carbon steel. 20× More
Image
Published: 31 October 2011
Fig. 1 Bond zone pattern typical of explosion clad metals. Materials are type 304L stainless steel and carbon steel. Original magnification: 20× More
Image
Published: 01 January 1993
Fig. 1 Bond zone pattern typical of explosion clad metals. Materials are type 304L stainless steel and medium-carbon steel. 20× More
Image
Published: 01 January 1994
Fig. 21 Clad metal windshield wiper socket, which consists of copper-clad, steel-clad phosphor bronze More
Image
Published: 01 January 2005
Fig. 10 Clad metal windshield wiper socket, which consists of copper-clad, steel-clad phosphor bronze More
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001458
EISBN: 978-1-62708-173-3
... Abstract Fabrication of high-density heat exchangers, which have a large heat transfer area and a compact size, is best accomplished by brazing where the brazing filler metal is clad to the materials to be brazed. This article focuses on the brazing procedures involved in the fabrication...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001442
EISBN: 978-1-62708-173-3
... steel weld cladding and the factors influencing joint integrity in dissimilar metal joining. It concludes with a discussion on joining carbon and low-alloy steels to various dissimilar materials (both ferrous and nonferrous) by arc welding. arc welding buildup alloys carbon steel dissimilar...
Series: ASM Handbook
Volume: 6A
Publisher: ASM International
Published: 31 October 2011
DOI: 10.31399/asm.hb.v06a.a0005632
EISBN: 978-1-62708-174-0
... one metal. When a cladding process is adopted, a base metal can be selected for cost or structural properties, and another metal added for surface protection or some other desired property, such as electrical conductivity. Common welding processes, such as gas metal arc, gas tungsten arc, or plasma...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001392
EISBN: 978-1-62708-173-3
... Abstract This article focuses on clad brazing material, which is defined as any base material or alloy that is clad with an appropriate lower-melting-point brazing filler metal. It provides information on typical clad brazing strip products in a tabular form and lists the advantages of using...
Image
Published: 01 January 1993
Fig. 24 Percentage of carbon in the deposit after base metal carbon and cladding dilution factors have been established. Source: Ref 26 More
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001376
EISBN: 978-1-62708-173-3
... is appropriate for use over a broad range of sizes. It has been used for joining electronic components of widths less than 0.5 mm (0.020 in.) and for cladding plates up to 5 × 13 m (16 × 40 ft). Cladding metal thicknesses can range from 0.025 to 100 mm (0.001 to 4 in.), and base metal thickness can range from...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001414
EISBN: 978-1-62708-173-3
.... It is normally measured by the percentage of base metal or previously deposited weld metal in the weld bead. Dilution control, which is of primary concern when joining dissimilar metal combinations, is described in detail in the article “Hardfacing, Weld Cladding, and Dissimilar Metal Joining” in this Volume...
Book Chapter

Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001380
EISBN: 978-1-62708-173-3
... pack rolling. It describes a patented roll welding process for fabrication of heat exchangers. The article presents a table showing the typical properties of common roll welded clad laminates. The relative weldability of selected dissimilar metals and alloys roll welded into clad-laminate form are also...
Series: ASM Handbook
Volume: 6A
Publisher: ASM International
Published: 31 October 2011
DOI: 10.31399/asm.hb.v06a.a0005602
EISBN: 978-1-62708-174-0
... explosive detonation explosives EXW parameters process-material interactions EXPLOSION WELDING (EXW), also known as explosive cladding, is accomplished by creating a high-velocity collision between two metal surfaces. The explosive detonation causes shock loading of one of the metals, the flyer...
Series: ASM Handbook
Volume: 6
Publisher: ASM International
Published: 01 January 1993
DOI: 10.31399/asm.hb.v06.a0001383
EISBN: 978-1-62708-173-3
.... , and Tkachenko S.G. , Influence of Friction Surfacing Conditions on Transition Layer Properties in Clad Metals , Svar, Proizvod. , Vol 9 , 1971 , p 32 – 33 7. Kershenbaum V.Ya. et al. , Performance of Steel Bronze Bimetal Produced by Friction Surfacing , Svar. Proizvod. , Vol 7 , 1972...
Series: ASM Handbook
Volume: 14A
Publisher: ASM International
Published: 01 January 2005
DOI: 10.31399/asm.hb.v14a.a0004013
EISBN: 978-1-62708-185-6
... ). The simultaneous deformation of the core and clad results in the formation of an interfacial bond. The coextrusion/codrawing operations can be carried out using conventional extrusion or drawing equipment as the basis for the forming operation, generally at a temperature appropriate to the metal system being...