1-20 of 272 Search Results for

castability

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006496
EISBN: 978-1-62708-207-5
... Abstract Castability is a complex characteristic that depends on both the intrinsic fluid properties of the molten metal and the manner in which the particular alloy solidifies. This article discusses the practical aspects of solidification important to aluminum foundrymen. The primary focus...
Series: ASM Handbook
Volume: 1A
Publisher: ASM International
Published: 31 August 2017
DOI: 10.31399/asm.hb.v01a.a0006326
EISBN: 978-1-62708-179-5
... describes the solidification shrinkage associated with the volume change that occurs during solidification, as well as strength and stiffness of ductile iron castings. It concludes with a discussion on the thermal deformation and residual stress in ductile iron castings. castability castings design...
Series: ASM Handbook
Volume: 1A
Publisher: ASM International
Published: 31 August 2017
DOI: 10.31399/asm.hb.v01a.a0006332
EISBN: 978-1-62708-179-5
... Abstract Castability of alloys is a measure of their ability to be cast to a given shape with a given process without the formation of cracks/tears, pores/shrinkage, and/or other significant casting defects. This article discusses the factors which affect the fluidity of an iron melt: alloy...
Series: ASM Handbook
Volume: 1A
Publisher: ASM International
Published: 31 August 2017
DOI: 10.31399/asm.hb.v01a.a0006328
EISBN: 978-1-62708-179-5
... Abstract The morphology of the graphite particles in compacted graphite iron (CGI) is intermediate to the graphite particles found in gray iron or ductile iron. This article discusses the castability and product design of compacted graphite iron. The introduction of modern measurement...
Book: Casting
Series: ASM Handbook
Volume: 15
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.hb.v15.a0005223
EISBN: 978-1-62708-187-0
... Abstract Castability of alloys is a measure of their ability to be cast to a given shape with a given process without the formation of casting defects. This article describes the factors that limit fluidity as well as experimental methods for measuring fluidity of various alloys. Various tests...
Image
Published: 30 November 2018
Fig. 19 Pumphrey-Moore cracking index based on castability data obtained from Al-Cu-Mg alloys. Source: Ref 19 More
Image
Published: 01 January 1993
Fig. 2 Pumphrey-Moore cracking index based on castability data obtained from aluminum-copper-magnesium alloys. Source: Ref 25 More
Image
Published: 09 June 2014
Fig. 20 General dry-out/heat-up schedule for conventional castable linings in induction heating applications. Courtesy of Allied Mineral Products More
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006578
EISBN: 978-1-62708-210-5
... Abstract The 391-type hypereutectic aluminum-silicon alloys are hypereutectic alloys designed for applications where excellent wear resistance is needed. They are similar to the 390 family of alloys, except for a low copper content to improve castability and corrosion resistance. This datasheet...
Series: ASM Handbook
Volume: 4C
Publisher: ASM International
Published: 09 June 2014
DOI: 10.31399/asm.hb.v04c.a0005840
EISBN: 978-1-62708-167-2
... the cracking that is associated with thermal cycling. Most fused silica castables have a nominal use temperature of approximately 1200 °C (2200 °F). At temperatures above 1200 °C (2200 °F), the fused silica converts to quartzite and will not withstand thermal cycling without cracking. This results in a maximum...
Book Chapter

Series: ASM Desk Editions
Publisher: ASM International
Published: 01 December 1998
DOI: 10.31399/asm.hb.mhde2.a0003134
EISBN: 978-1-62708-199-3
... describes the major factors considered in alloy selection for casting, including raw material cost, castability, machinability, and the bearing and wear properties. It also provides information on the cost of the final product. alloy selection bearing properties castability conductivity copper...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006571
EISBN: 978-1-62708-210-5
...-magnesium die-casting alloys mechanical properties; physical properties Alloys 360.0 and A360.0 are hypoeutectic Al-Si-Mg die-casting alloys with restricted copper content ( Table 1 ). They have very good castability and good corrosion resistance, but fair machinability, less generous limitations...
Series: ASM Handbook
Volume: 2A
Publisher: ASM International
Published: 30 November 2018
DOI: 10.31399/asm.hb.v02a.a0006524
EISBN: 978-1-62708-207-5
... Abstract Aluminum casting alloys are among the most versatile of all common foundry alloys and generally have high castability ratings. This article provides an overview of the common methods of aluminum shape casting. It discusses the designations of aluminum casting alloys categorized...
Image
Published: 01 December 2004
Fig. 20 Six low-carbon steel sheet specimens, separated by steel spacers, showing (a) damage from mounting in a thermosetting phenolic resin and (b) lack of damage when mounted in a castable epoxy More
Image
Published: 01 December 2004
Fig. 19 A low-carbon steel sheet plated with electroless nickel showing (a) damage to the coating from mounting in a thermosetting phenolic resin and (b) the lack of damage when mounted in a castable epoxy. As-polished. 100× More
Series: ASM Handbook
Volume: 1A
Publisher: ASM International
Published: 31 August 2017
DOI: 10.31399/asm.hb.v01a.a0006329
EISBN: 978-1-62708-179-5
... casting, with particular emphasis on the melting practices, molten metal treatment, and feeding of molten metal into sand molds. It discusses the castability factors, such as fluidity, shrinkage, and resistance, of gray iron. Typical cupola charge compositions and the final analyses for class 30 and class...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006563
EISBN: 978-1-62708-210-5
... 9.0 34 5.0 17 10 4 52 7.5 34 5.0 25 Source data are in English units; metric values are converted and rounded Alloy 332.0 has many characteristics like 336.0, while offering improved castability and machinability ( Ref 1 ). This alloy retains strength at elevated temperatures...
Image
Published: 01 December 2004
Fig. 21 A zinc-particle polymer coating (Zincrometal) with a top paint layer on a low-carbon steel sheet showing (a) the extent of the top paint layer, using transmitted light through a castable epoxy mount, and (b) the difficulty of seeing the paint layer in a normal brightfield illumination More
Book Chapter

Series: ASM Handbook
Volume: 9
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.hb.v09.a0003786
EISBN: 978-1-62708-177-1
... provides information on the molds and resins used for castable mounts, vacuum treatment of mounts, special mount arrangements, and mount marking and storage. castable mounts cleaning compression molded mounts handling mechanical clamps metallographic polishing mount defects mount marking...
Series: ASM Handbook
Volume: 2B
Publisher: ASM International
Published: 15 June 2019
DOI: 10.31399/asm.hb.v02b.a0006579
EISBN: 978-1-62708-210-5
...-silicon die casting alloys fabrication characteristics mechanical properties physical properties Alloy 413.0 is a eutectic binary Al-Si alloy with excellent castability and very good corrosion resistance. With poor machinability, it does not lend itself to producing a good surface finish...